GB/T 3903.1-2017 PDF English
US$80.00 · In stock · Download in 9 secondsGB/T 3903.1-2017: Footwear -- Test methods for whole shoe -- Flexing resistance Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedureStatus: Valid GB/T 3903.1: Evolution and historical versions
| Standard ID | Contents [version] | USD | STEP2 | [PDF] delivery | Name of Chinese Standard | Status |
| GB/T 3903.1-2017 | English | 80 |
Add to Cart
|
0-9 seconds. Auto-delivery
|
Footwear -- Test methods for whole shoe -- Flexing resistance
| Valid |
| GB/T 3903.1-2008 | English | 170 |
Add to Cart
|
0-9 seconds. Auto-delivery
|
Footwear -- General test methods -- Flexing resistance
| Obsolete |
| GB/T 3903.1-1994 | English | 199 |
Add to Cart
|
2 days
|
General test method for footwear-Test method of flexing resistance
| Obsolete |
| GB 3903-1983 | English | 199 |
Add to Cart
|
2 days
|
Test method for peeling strength of leather shoes
| Obsolete |
Excerpted PDFs (Download full copy in 9 seconds upon purchase)PDF Preview: GB/T 3903.1-2017
GB/T 3903.1-2017: Footwear -- Test methods for whole shoe -- Flexing resistance---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT3903.1-2017
GB
NATIONAL STANDARD OF THE
PEOPLE’S REPUBLIC OF CHINA
ICS 61.060
Y 78
Replacing GB/T 3903.1-2008
Footwear -- Test methods for whole shoe --
Flexing resistance
Issued on. DECEMBER 29, 2017
Implemented on. JULY 1, 2018
Issued by. General Administration of Quality Supervision, Inspection and
Quarantine of the People’s Republic of China;
Standardization Administration of the People’s Republic of
China.
Table of Contents
Foreword... 3
1 Scope... 4
2 Normative references... 4
3 Principle... 4
4 Apparatus... 5
5 Test piece... 6
6 Test conditions... 6
7 Test procedures... 7
8 Test results... 8
9 Test report... 8
Foreword
This Standard was drafted in accordance with the rules given in GB/T 1.1-2009.
This Standard supersedes GB/T 3903.1-2008 Footwear -- General test
methods -- Flexing resistance. Compared with GB/T 3903.1-2008, the main
technical differences are as follows.
— MODIFY the standard name;
— MODIFY the scope of application of the standard;
— MODIFY the description of the standard principle;
— MODIFY the number of samples;
— ADD the requirements for holders in the flexing resistance testers;
— MODIFY the test procedures;
— MODIFY the description of the test results.
Attention is drawn to the possibility that some of the elements of this document
may be the subject of patent rights. The issuing authority shall not be held
responsible for identifying any or all such patent rights.
This Standard was proposed by the China National Light Industry Council.
This Standard shall be under the jurisdiction of National Technical Committee
for Standardization of Shoemaking (SAC/TC 305).
Drafting organizations of this Standard. China Leather and Footwear Industry
Research Institute, Anta (China) Co., Ltd, Dezhou Xinhuarun Technology Co.,
Ltd, China Leather and Footwear Industry Research Institute (Jinjiang) Co., Ltd,
Guangdong Wanlima Industry Co., Ltd.
Main drafters of this Standard. Qin Xiaobo, Li Su, Li Yucai, Shi Yiwei, Shen
Yimin, Ye Yahong.
The previous released editions of this Standard are as follows.
— GB 3904-1983.
— GB/T 3903.1-1994, GB/T 3903.1-2008.
Footwear -- Test methods for whole shoe --
Flexing resistance
1 Scope
This Standard specifies the test methods for flexing resistance of whole shoes
or soles.
This Standard is applicable to whole shoes and soles.
This Standard is not applicable to the whole shoes or soles with a height greater
than 70mm, or a thickness of the sole flexion site greater than 25mm, or a
bending angle less than 45° after rigidity is tested according to the provisions
of 8.4.1 in GB/T 20991-2007.
NOTE 1.The thickness of the sole flexion site includes the thickness of the insole.
NOTE 2.The sole material (sheet) can be determined with reference to this Standard.
2 Normative references
The following documents are essential to the application of this document. For
dated references, only the editions with the dates indicated are applicable to
this document. For undated references, only the latest editions (including all the
amendments) are applicable to this document.
GB/T 20991-2007 Personal protective equipment -- Test methods for
footwear
GB/T 22049 Footwear -- Standard atmospheres for conditioning and testing
of footwear and components for footwear
3 Principle
After a whole shoe or sole is conducted with the flexing test on a flexing
resistance tester at a certain flexing angle and frequency, OBSERVE the
changes in upper, sole, and upper-sole bonding site.
4 Apparatus
4.1 Flexing resistance tester
4.1.1 The flexing angle is adjustable from 0° to 55°.
4.1.2 The flexing frequency is adjustable within the range of 100 times / min
to 300 times / min.
4.1.5 A device is provided for blasting the flexure of the test piece.
4.2 Flexible test last
4.2.1 A steel shaft in size of ϕ (5.5 ± 0.5)mm × (40 ± 2)mm is fitted on the
vertical line from the first metatarsophalangeal site to the axis of last bottom of
the flexible test last. There is no bump on the surface of the steel shaft relative
to the last bottom.
4.3 Vernier caliper
At least accurate to 0.02mm.
4.4 Cutting knife
The schematic diagram of the cutting knife is shown in Figure 1.
5 Test piece
Each set of test pieces shall not be less than one pair of whole shoes or soles.
In addition, the adhesion of test pieces requires at least 24h.
6 Test conditions
6.1 The flexing angle of the flexing resistance tester is (50 ± 1)° (in case of
special requirements, it can be selected between 0° and 55°).
6.2 The flexing frequency of the flexing resistance tester is (230 ± 10) times /
min (in case of special requirements, it can be selected within the range of 100
times / min to 300 times / min).
7 Test procedures
7.1 Before the test, in accordance with the provisions of GB/T 22049, the test
pieces shall be placed at a standard ambient temperature of (23 ± 2) °C for at
least 4h.
7.4 BEND the test pieces. MARK the position of metatarsophalangeal flexion
on both sides of the shoe. CONNECT these two positions to draw a flex line on
the sole.
7.5 CLAMP the test pieces in the holder of the flexing resistance tester (4.1).
The flex line on the sole, the steel shaft of the flexible test last, and the axis of
the holder’s movable shaft shall be at the same level.
7.6 PLACE the tester at the minimum flexing angle. ADJUST the tilt angle of
the holder. OBSERVE the position of the heel so that the test piece is in a
natural state without being bent in any direction.
7.7 ADJUST the eccentricity of the tester so that the flexing angle reaches the
specified angle (6.1).
7.8 If cutting is required, SLICE a 5mm long cut in the middle of the flex line
on the sole. In addition, CUT through the sole.
7.9 RESET the counter of the tester. PRESET the number of flexing to 40,000
times (in case of other requirements in the product standards, it shall be
implemented according to the product standards). ACTIVATE the blower. Then
TURN on the main unit.
8 Test results
8.1 RECORD the number of new cracks and the length of the longest new
crack; and the de-bonding length of the upper-sole (including the foxing and
outsole) bonding site.
8.2 If there is a pre-cut, RECORD the extended length of the cut on the sole,
in millimeters. The result is retained to one decimal place.
8.4 The test results of each shoe (sole) are indicated separately.
9 Test report
The test report shall include at least the following.
......
Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al.
Tips & Frequently Asked QuestionsQuestion 1: How long will the true-PDF of English version of GB/T 3903.1-2017 be delivered?Answer: The full copy PDF of English version of GB/T 3903.1-2017 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice. Question 2: Can I share the purchased PDF of GB/T 3903.1-2017_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 3903.1-2017_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet. Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 3903.1-2017 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds. Question 5: Should I purchase the latest version GB/T 3903.1-2017?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 3903.1-2017 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically. How to buy and download a true PDF of English version of GB/T 3903.1-2017?A step-by-step guide to download PDF of GB/T 3903.1-2017_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).
Step 2: Search keyword "GB/T 3903.1-2017".
Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart.
Step 4: Select payment option (Via payment agents Stripe or PayPal).
Step 5: Customize Tax Invoice -- Fill up your email etc.
Step 6: Click "Checkout".
Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively.
Step 8: Optional -- Go to download PDF.
Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice.
See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |