YS/T 579-2014 English PDFUS$159.00 ยท In stock
Delivery: <= 3 days. True-PDF full-copy in English will be manually translated and delivered via email. YS/T 579-2014: Vandium-Aluminum master alloy Status: Valid YS/T 579: Historical versions
Basic dataStandard ID: YS/T 579-2014 (YS/T579-2014)Description (Translated English): Vandium-Aluminum master alloy Sector / Industry: Nonferrous Metallurgy Industry Standard (Recommended) Classification of Chinese Standard: H63 Classification of International Standard: 77.150.99 Word Count Estimation: 6,618 Date of Issue: 10/14/2014 Date of Implementation: 4/1/2015 Older Standard (superseded by this standard): YS/T 579-2006 Regulation (derived from): People's Republic of China Ministry of Industry and Information Technology Notice 2014 No. 63; Industry Standard Filing Notice 2014 No. 12 (Overall No. 180) Issuing agency(ies): Ministry of Industry and Information Technology Summary: This Standard specifies requirements for vanadium aluminum master alloy, test methods, inspection rules, marking, packaging, transportation, storage and quality certificates and contracts (or orders) content. This Standard applies to the use of vanadium a YS/T 579-2014: Vandium-Aluminum master alloy---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order.Vandium-Aluminum master alloy ICS 77.150.99 H63 People's Republic of China Nonferrous Metals Industry Standard Replacing YS/T 579-2006 Vanadium aluminum master alloys Issued on. 2014-10-14 2015-04-01 implementation Ministry of Industry and Information Technology of the People's Republic of China released ForewordThis standard was drafted in accordance with GB/T 1.1-2009 given rules. Instead of the standard YS/T 579-2006 "vanadium aluminum master alloy." This standard YS/T 579-2006 compared to the main changes are as follows. --- Increased requirements N elements; --- Of Fe, C, O, Si element content has been adjusted; --- On size range has been adjusted; --- Increase the surface of the nitride requirements; --- Adjust the high density inclusions inspection requirements; --- Of inspection rules were revised. This standard by the national non-ferrous metals Standardization Technical Committee (SAC/TC243) centralized. This standard is drafted by. Baoji Titanium Group Co., Ltd. Dalian Rong Gaudet kinds of materials, Chengde Vanadium big public limited liability Secretary, Baoji Titanium Industry Co., Ltd., Baoji Titanium Special Metals Co.. The main drafters of this standard. Robin Li Fengjun Ning, Mao Lingling, Liu Zhiguang, Sui Yingdan, Liu, Wang Chang Jian, Rong Yang, Liu Min, Lixian Jun. This standard replaces the standards previously issued as follows. --- YS/T 579-2006. Vanadium aluminum master alloys1 ScopeThis standard specifies requirements for vanadium aluminum master alloy, test methods, inspection rules, marking, packaging, transportation, storage and quality certificate hehe Same (or orders) content. This standard applies to the use of hot metal produced by reduction of vanadium aluminum master alloy (hereinafter referred to as the product). The titanium alloy can be used as high Temperature alloys and other special alloys additives.2 RequirementsGrade 2.1 Product by chemical composition into AlV55, AlV65, AlV75 and AlV85 total of four grades. 2.2 Chemical composition Chemical composition of the product shall comply with the requirements in Table 1. Table 1 % Trademark Principal component impurity element of not more than V Al Fe Si CON AlV55 50.0 ~ 60.0 margin 0.25 0.25 0.10 0.18 0.04 AlV65 > 60.0 ~ 70.0 margin 0.25 0.25 0.10 0.18 0.04 AlV75 > 70.0 ~ 80.0 margin 0.30 0.25 0.15 0.30 0.05 AlV85 > 80.0 ~ 90.0 margin 0.30 0.25 0.25 0.50 0.05 NOTE. There are special requirements for chemical composition, the two sides negotiated by supply and demand. 2.3 size and tolerance 2.3.1 Product delivery by granular particle size in the range of 0.25mm ~ 6.3mm. Allowing a small amount beyond the size range of products, but their number Delivery batch weight should not exceed 4%. 2.3.2 If the demand side of the product size have special requirements, both parties determined by supply and demand. 2.4 appearance quality Product surface should be clean, it does not allow the oxide film visual evidence nitride film and other metallic and non-metallic inclusions. 2.5 High-density inclusions Products should be no high-density inclusions and other foreign substances. Demand side and specified in the contract (or purchase order) when you should be 100% test. ......Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of YS/T 579-2014_English be delivered?Answer: Upon your order, we will start to translate YS/T 579-2014_English as soon as possible, and keep you informed of the progress. The lead time is typically 1 ~ 3 working days. The lengthier the document the longer the lead time.Question 2: Can I share the purchased PDF of YS/T 579-2014_English with my colleagues?Answer: Yes. The purchased PDF of YS/T 579-2014_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay.Question 5: Should I purchase the latest version YS/T 579-2014?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version YS/T 579-2014 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically. |
