YS/T 336-2010 English PDFUS$139.00 · In stock
Delivery: <= 2 days. True-PDF full-copy in English will be manually translated and delivered via email. YS/T 336-2010: Methods of fracture test for tube and rod of copper and copper alloys, nickel and nickel alloys Status: Valid YS/T 336: Historical versions
Basic dataStandard ID: YS/T 336-2010 (YS/T336-2010)Description (Translated English): Methods of fracture test for tube and rod of copper and copper alloys, nickel and nickel alloys Sector / Industry: Nonferrous Metallurgy Industry Standard (Recommended) Classification of Chinese Standard: H24;H13 Classification of International Standard: 77.040.99 Word Count Estimation: 5,517 Date of Issue: 2010-11-22 Date of Implementation: 2011-03-01 Older Standard (superseded by this standard): YS/T 336-1994 Regulation (derived from): MIIT (2010) No. 126 Issuing agency(ies): Ministry of Industry and Information Technology Summary: This standard specifies the copper, nickel and alloy pipes and rods fracture test of principle of the method, the general requirements, sample preparation, testing methods, results determined that inspection reports. This standard applies to copper, nickel and alloy pipe, rod fracture test. According to fracture test to determine the quality of the interior tube rods. YS/T 336-2010: Methods of fracture test for tube and rod of copper and copper alloys, nickel and nickel alloys---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order. Methods of fracture test for tube and rod of copper and copper alloys, nickel and nickel alloys ICS 77.040.99 H13 People's Republic of China Nonferrous Metals Industry Standard Replacing YS/T 336-1994 Copper, nickel and alloy pipe and bar fracture test aloys, nickelandnickelaloys Issued on. 2010-11-22 2011-03-01 implementation Ministry of Industry and Information Technology of the People's Republic of China released ForewordInstead of the standard YS/T 336-1994 "copper, nickel and alloy pipe and bar fracture test." Compared with this standard YS/T 336-1994, the main changes are as follows. Content --- the addition of foreword, scope, methods, principles, inspection reports; --- "4 Sample Preparation" added "to break the fracture should be kept clean and not allowed to damage or contamination" and so on; --- In "5 test methods" provides that "the fracture should be visual inspection, visual identification is difficult, can be 10 times the magnifying glass inspection Inspection, and defect size determination. " This standard by the National Standardization Technical Committee of non-ferrous metals and centralized. The standard by Chinalco Luoyang Copper Co., Ltd. is responsible for drafting. The main drafters of this standard. Zhu Yingli, Menghui Juan, Zhao million to spend, steady Guo Hui, Cao Li, Wen positive thunderstorm. This standard replaces the standards previously issued as follows. --- YS/T 336-1994, YB732-1971. Copper, nickel and alloy pipe and bar fracture test1 ScopeThis standard specifies the principle of the method of copper, nickel and alloy pipe and bar fracture test methods, general requirements, sample preparation, test side Law, the results of determination, inspection reports. This standard applies to copper, nickel and alloy pipe, rod fracture test. According to fracture test to determine the quality of the internal tube rod Happening.2 principle of the methodThe article by manual or mechanical break with visual inspection of the fracture.3 Requirements3.1 fracture test should end product (extruded products against pressure than the end) were. 3.2 fracture test shall be the number of the corresponding standard product requirements or by both parties through consultation.4 Sample PreparationBroken pipe and bar fracture width 4.1 shall comply with the requirements in Table 1 and Table 2. Table 1 pipe fracture width Pipe diameter / mm Fracture width / mm Sawing method ≤50 ≥ 40% of the pipe diameter > 50 ≥20 Both sides remain central sawing Note 1. ≤25mm inner diameter of the pipe, saw both sides, the fracture width may not be less than 15mm. Note 2. Lead brass tubing allows side cutting, the fracture width of not less than 50% of the pipe diameter. Table 2 bars break width Bar diameter / mm Fracture width / mm Sawing method < 16 ≥5 (or ≥2/3 diameter) saw both sides ≥16 ~ 40 50% ≥ bar diameter side sawing ≥10 sides remain central sawing > 40 ≥10 saw both sides remain central ......Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of YS/T 336-2010_English be delivered?Answer: Upon your order, we will start to translate YS/T 336-2010_English as soon as possible, and keep you informed of the progress. The lead time is typically 1 ~ 2 working days. The lengthier the document the longer the lead time.Question 2: Can I share the purchased PDF of YS/T 336-2010_English with my colleagues?Answer: Yes. The purchased PDF of YS/T 336-2010_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay.Question 5: Should I purchase the latest version YS/T 336-2010?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version YS/T 336-2010 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically. |
