QC/T 1206.2-2024 PDF EnglishUS$155.00 · In stock · Download in 9 seconds
QC/T 1206.2-2024: Thermal management system for electric vehicle traction battery - Part 2: Liquid cooling system Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid
Similar standardsQC/T 1206.2-2024: Thermal management system for electric vehicle traction battery - Part 2: Liquid cooling system---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/QCT1206.2-2024 QC AUTOMOBILE INDUSTRY STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 43.120 CCS T 47 Thermal management system for electric vehicle traction battery - Part 2: Liquid cooling system ISSUED ON: JULY 19, 2024 IMPLEMENTED ON: JANUARY 01, 2025 Issued by: Ministry of Industry and Information Technology of the People's Republic of China. Table of ContentsForeword ... 3 Introduction ... 4 1 Scope ... 5 2 Normative references ... 5 3 Terms and definitions ... 5 4 Requirements ... 6 5 Test methods ... 9 6 Inspection rules ... 14 7 Labeling, packaging, transportation and storage ... 16 Thermal management system for electric vehicle traction battery - Part 2: Liquid cooling system1 ScopeThis document specifies the technical requirements and test methods for liquid cooling systems for electric vehicle power batteries (hereinafter referred to as "batteries"). This document is applicable to the research, development and testing of electric vehicle power battery liquid cooling systems and their components.2 Normative referencesThe following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. GB/T 2408-2021, Plastics -- Determination of burning characteristics -- Horizontal and vertical test GB/T 19596, Terminology of electric vehicles GB 38031-2020, Electric vehicles traction battery safety requirements QC/T 468-2010, Automobile radiator QC/T 1206.1-2024, Thermal management system for electric vehicle traction battery Part 1: General requirements3 Terms and definitionsFor the purposes of this document, the terms and definitions defined in GB/T 19596, QC/T 1206.1-2024 as well as the followings apply. 3.1 liquid cooling system A system that uses a coolant (such as a mixed solution of ethylene glycol and water) as a heat exchange medium to cool the battery. NOTE: It is generally composed of liquid cooling plate, liquid cooling pipe, joint, water inlet and outlet assembly and other components, as shown in Figure 1. After the flow resistance test is carried out in accordance with 5.4, the flow resistance of the liquid cooling system shall meet the technical requirements specified by the manufacturer. 4.3 Safety performance 4.3.1 Sealing After the sealing test is carried out in accordance with 5.5, one of the following requirements shall be met: a) Wet test: no visible bubbles; b) Dry test: leakage is no more than 2.5 mL/min; c) Helium test: leakage rate is no more than 2×10-6 Pa•m3/s. 4.3.2 Flame retardancy After the flame retardancy test is carried out in accordance with 5.6, the horizontal combustion grade of non-metallic parts of the liquid cooling system shall meet the requirements for grade HB in GB/T 2408-2021. 4.4 Technical requirements 4.4.1 Pressure resistance After the pressure test according to 5.7, the liquid cooling system shall be leak-free. The deformation in the deformation direction shall not exceed 10% of the original size. 4.4.2 Vibration After the vibration test is carried out in accordance with 5.8, the liquid cooling system shall meet the requirements of 4.3.1. 4.4.3 Welding strength After the welding strength test is carried out in accordance with 5.9, there shall be no damage or cracks at the joint welding. 4.4.4 Burst pressure During the burst pressure test according to 5.10, the liquid cooling plate and liquid cooling pipeline shall not be damaged or loose. 4.4.5 High and low temperature cycle After the high and low temperature cycle test is carried out in accordance with 5.11, the liquid cooling system shall meet the requirements of 4.3.1. 5.6.1 Test object: liquid cooling system. 5.6.2 Test content: non-metallic parts of the liquid cooling system shall be subjected to horizontal combustion test in accordance with the provisions of Chapter 8 of GB/T 2408-2021. 5.7 Pressure resistance 5.7.1 Test object: liquid cooling system. 5.7.2 Perform the test according to the following steps: a) Continuously introduce gas greater than or equal to 250 kPa into the liquid cooling system. Immerse in water and observe for 1 h; b) Observe whether there are bubbles. Finally, take the liquid cooling system out of the water and check its appearance. 5.8 Vibration 5.8.1 Test object: battery system. 5.8.2 Perform the test according to the following steps: a) Test the battery system according to the vibration test method specified in 8.2.1 of GB/T 38031-2020; b) Perform a sealing test on the battery liquid cooling system after vibration according to 5.5. 5.9 Welding strength 5.9.1 Test object: liquid cooling plate. 5.9.2 Perform the test according to the following steps: a) Fix the liquid cooling plate on the test bench according to the actual assembly method. Use the fixture to press the liquid cooling plate body instead of the battery. Drill holes on the joints of the liquid cooling plate. The pull-out force test hook is vertically hooked on the joint hole. The tensile machine slowly pulls to 500 N; b) Check the appearance of the jointer and the liquid cooling plate welding point. 5.10 Burst pressure 5.10.1 Test object: liquid cooling system. 5.10.2 Perform the test according to the following steps: 5.12.1 Test object: liquid cooling system. 5.12.2 Perform the test according to the following steps. a) Before the test, the liquid cooling system is filled with a mixed solution consisting of antifreeze and ASTM solution in a volume ratio of 4:6. NOTE: Antifreeze type: 45% ethylene glycol antifreeze. Freezing temperature is -30℃; ASTM solution: a solution prepared by 1 L of distilled water, 148 mg of sodium sulfate, 165 mg of sodium chloride, and 138 mg of sodium bicarbonate. b) The temperature of the mixed solution is 45°C ± 2°C. The flow rate is set according to the manufacturer’s requirements. c) Run for 76 h and stop for 8 h as one cycle. A total of 14 cycles. Check the solution pH and appearance during the stop. Refill the solution. d) After the test, carry out a sealing test in accordance with 5.5. 5.13 Pressure alternation 5.13.1 Test object: liquid cooling system. 5.13.2 Perform the test according to the following steps: a) At 25℃±2℃, introduce pressure alternating coolant into the liquid cooling system; b) The pressure of the coolant rises from 30 kPa to 200 kPa, and then drops to 30 kPa after holding the pressure, which is a pressure cycle. The cycle period is 6 s~10 s. The holding time is 3 s~6 s. The coolant temperature is 45℃±2℃; c) The test cycle is 5×104 times; d) After the test, carry out a sealing test in accordance with 5.5. 5.14 Multiple plugging and unplugging 5.14.1 Test object: liquid cooling pipe joint. 5.14.2 Perform the test according to the following steps: a) Install the pipe jointer on the liquid cooling plate. Place at 80℃ for 30 min. Let in 205 kPa air. Then cool to 25℃±2℃. Remove the jointer and reinstall it according to the operating specifications; b) Repeat step a) 20 times. Let in 205 kPa of air. Maintain the pressure at 25℃±2℃ for 10 min; c) After the test, carry out a sealing test in accordance with 5.5. 5.15 Jointer installation force 5.15.1 Test object: liquid cooling pipe joint. 5.15.2 Perform the test according to the following steps: a) At 25℃ ±2℃, insert the joint into the liquid cooling plate at a speed of 50 mm/min±5 mm/min until it is plugged into place; b) Record the installation force of the joint during installation. 5.16 Jointer pull-off force 5.16.1 Test object: liquid cooling pipeline jointer. 5.16.2 Perform the test according to the following steps: a) Install the jointer on a tensile testing machine at 25℃±2℃. Apply tensile force at a rate of 50 mm/min±5 mm/min until the quick-connect jointer is pulled out of the liquid cooling plate jointer; b) Record the pull-off force when the jointer is installed. 5.17 Negative pressure resistance 5.17.1 Test object: liquid cooling system. 5.17.2 Perform the test according to the following steps: a) At 25℃±2℃, assemble the liquid cooling plate and liquid cooling pipeline according to the actual state; b) Apply a pressure of -(90±2) kPa to the inside of the liquid cooling system. Maintain the pressure for 60 s and then return to normal pressure; c) Repeat steps a)~b) 5 times; d) After the test, perform a sealing test according to 5.5.6 Inspection rules6.1 Inspection items See Table 3 for inspection items and requirements. ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of QC/T 1206.2-2024 be delivered?Answer: The full copy PDF of English version of QC/T 1206.2-2024 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of QC/T 1206.2-2024_English with my colleagues?Answer: Yes. The purchased PDF of QC/T 1206.2-2024_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- QC/T 1206.2-2024 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.How to buy and download a true PDF of English version of QC/T 1206.2-2024?A step-by-step guide to download PDF of QC/T 1206.2-2024_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "QC/T 1206.2-2024". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
