JJF 1310-2011 English PDFUS$399.00 · In stock
Delivery: <= 3 days. True-PDF full-copy in English will be manually translated and delivered via email. JJF 1310-2011: Calibration Specification for Electronic Plug Gauges Status: Valid JJF 1310: Historical versions
Basic dataStandard ID: JJF 1310-2011 (JJF1310-2011)Description (Translated English): Calibration Specification for Electronic Plug Gauges Sector / Industry: Metrology & Measurement Industry Standard Classification of Chinese Standard: A52 Classification of International Standard: 17.040 Word Count Estimation: 17,144 Date of Issue: 2011-09-14 Date of Implementation: 2011-12-14 Quoted Standard: JJG 894-1995; JJF 1001-1998; JJF 1059-1999; JB/T 7429-2006 Regulation (derived from): State Administration of Quality Supervision, Inspection and Quarantine Notice 2011 No. 134 Issuing agency(ies): General Administration of Quality Supervision, Inspection and Quarantine Summary: This standard applies to measuring range of 130mm diameter 6mm-diameter two-point calibration of electronic plug, this plug outside the scope of electronics and electronic plug-point calibration can be calibrated with reference to the specification. JJF 1310-2011: Calibration Specification for Electronic Plug Gauges---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order.Calibration Specification for Electronic Plug Gauges People's Republic of China National Metrology Technical Specifications Electronic plug gauge calibration specification Issued on. 2011-09-14 2011-12-14 implementation The State Administration of Quality Supervision, Inspection and Quarantine released Electronic plug gauge calibration specification This specification by the State Administration of Quality Supervision, Inspection and Quarantine approved on September 14, 2011, and from From December 14, 2011 implementation. NFP. National Engineering Geometrical Parameters Measurement Technology Committee Main drafting unit. Guangxi Institute of measurement testing Heilongjiang Provincial Academy of verification test Participated in the drafting unit. Meter Zhongyuan Ltd. Sanmenxia in measuring instrument Co., Ltd. Jiangsu Province Institute of Metrology This specification project commissioned by the National geometric parameter measurement technology committee responsible for the interpretation The main drafters of this specification. Full Yi-chi (Guangxi Institute of measurement detection) Lu Rui (Guangxi Institute of measurement detection) Liang Yuhong (Heilongjiang Provincial Academy of verification test) Drafters participate. Zhang Hongfei (Zhongyuan Measuring Instruments Co., Ltd.) Ji Yihong (Sanmenxia in measuring instrument Co., Ltd.) Goal Orientation (Jiangsu Province Institute of Metrology) table of Contents1 Scope (1) 2. Referenced Documents (1) 3 Terms and Definitions (1) 4 Overview (1) 5 Metrological characteristics (2) 5.1 Calibration with a standard ring gauge diameter and the amount of variation in diameter (2) 5.2 Work space (2) Measuring force 5.3 (2) 5.4 probing surface and guide face surface roughness (2) 5.5 Zero balance (3) 5.6 Zero range (3) 5.7 Probe alignment error (3) 5.8 Probe symmetry error (3) 5.9 Indication error (3) 5.10 Indication variability (3) Drift 5.11 (3) 6 calibration conditions (4) Environmental conditions 6.1 (4) 6.2 measurement standards (4) 7 calibration items and calibration methods (4) 7.1 calibration items (4) 7.2 Calibration method (5) 8 calibration results expression (6) 9 Recalibration interval (6) Appendix A electronic plug gauge indication error measurement Uncertainty Evaluation (7) Appendix B calibration certificate content and in-page format (10) Electronic plug gauge calibration specification1 ScopeThis standard applies to the measurement range of φ6mm ~ two electronic plug gauge φ130mm calibration, this range Electronic plug gauge plug gauge and three-point electronic calibration can be outside of this specification with reference to the calibration.2 CitationsThis specification references the following documents. JJG894-1995 standard ring gauge JJF 1001-1998 common measurement terms and definitions JJF 1059-1999 Evaluation and Expression of Uncertainty in Measurement JB/T 7429-2006 electronic plug gauge When using this specification it should be noted that using the currently valid version of the documents cited.3 Terms and Definitions3.1 Work space workingclearance Deviation of the difference between the size of the maximum diameter of the hole diameter and the measured electronic plug gauge guide sleeve. 3.2 Probe alignment errors contactvariationagainstcerterline Two plug connections departing from the probe contacts the measurement error plug wire guide sleeve shaft diameter generated. 3.3 Probe symmetric error contactsymmetricdifferent Plug two probes lever hinge mechanism with respect to the central axis of the asymmetric shift plug arising from measurement error. 3.4 Zero balance nulbalance The pointing device in the conversion range gear, showing the value of each block of the zero offset. 3.5 Indication variability instability In the case of the measurement conditions do not make any changes, it is measured against the same number of measurements between the maximum result difference.4 OverviewElectronics is a plug-contact measurement aperture comparative measurement instruments, will be measured by the inductive sensor aperture size changes Into electrical signals, and then by indicating means for indicating the measured aperture size deviation. Electronic plug by the plug body, indicating means (Pointer table, DRO or electron column) and the composition of the calibration standard ring gauge. Electronic plug according to the number of probes can be divided into two Point and three-point, two-point common electronic plug gauge its shape structure shown in Figure 1. ......Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of JJF 1310-2011_English be delivered?Answer: Upon your order, we will start to translate JJF 1310-2011_English as soon as possible, and keep you informed of the progress. The lead time is typically 1 ~ 3 working days. The lengthier the document the longer the lead time.Question 2: Can I share the purchased PDF of JJF 1310-2011_English with my colleagues?Answer: Yes. The purchased PDF of JJF 1310-2011_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay.Question 5: Should I purchase the latest version JJF 1310-2011?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version JJF 1310-2011 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically. |