HG/T 20615-2009 PDF EnglishUS$225.00 · In stock · Download in 9 seconds
HG/T 20615-2009: Steel pipe flanges (Class designated) Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid HG/T 20615: Historical versions
Similar standardsHG/T 20615-2009: Steel pipe flanges (Class designated)---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/HGT20615-2009Chemical Industry Standard of the People's Republic of China HG Replacing HG 20615~20622-1997, HG 20624~20626-1997 Steel Pipe Flanges (Class designated) [Including Corrigendum/Modification confirmed in May 2012.Text in RED] Issued on. FEBRUARY 5, 2009 Implemented on. JULY 1, 2009 Issued by. Ministry of Industry and Information Technology of the People's Republic China Table of Contents1.General provisions... 3 2.Normative references... 3 3.Flange style and flange sealing surface... 5 3.1 Flange type... 5 3.2 Flange sealing face... 9 4.Materials... 17 5.Gaskets and bolting for flange... 19 6.Fitting of flange joint... 19 7.Pressure-temperature rating... 19 8.Dimensions... 34 8.1 Coupling dimension of the pipe flange... 34 8.2 Physical dimension of the pipe flange... 37 8.3 Pipe flange neck... 80 8.4 Pipe thread... 81 9.Welding joint and groove dimension... 81 10.Dimension tolerance... 83 11.Test... 85 12.Inspection and acceptance... 85 13.Markings and illustrations... 85 14.Packaging and steel seal labeling... 87 Appendix A (Normative) Steel Orifice Flange... 89 Appendix B (Informative) Steel Jacket Flange... 99 Appendix C (Informative) Inside Diameter of the Weld Neck Pipe Flange... 109 Appendix D (Informative) Assorted Pipe Flanges' Standard... 110 Appendix E (Informative) Approximate Mass of the Pipe Flanges... 111 Appendix F (Informative) Approximate Distance between the Ring Joint Face Flanges ... 117 1.General provisions 1.0.1 This national standard specifies the basic technical requirements of steel pipe flanges (Class designated), including nominal dimension, nominal pressure, material, pressure-temperature rating, flange type, dimension, sealing face, tolerance and marking. 1.0.2 This Standard is applicable to steel pipe flange and blind flange with nominal pressure of Classl50 (PN20)~Class2500 (PN420). The nominal pressure grade of the flange is denoted by Class, including the following six grades. Classl50, Class300, Class600, Class900, Classl500 and Class2500. 1.0.3 The applied nominal dimension DN and outside diameter of the steel pipe in this Standard are in accordance with those specified in Table 1.0.3. 1.0.4 This Standard is also applicable to valve, pump, chemical engineering machinery, pipeline fittings and equipment spares with flange being used as its type of attachment. 1.0.5 This Standard excludes selection principle for materials under particular fluid operating conditions. 2.Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this Standard. For dated reference, subsequent amendments (excluding content of corrigenda) to, or revisions of, any of these publications do not apply. However, Parties to agreements based on this Code are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. For undated references, the latest edition of the normative document referred to applies. "Pipework Components--Definition and Selection of DN (Nominal Dimension)" GB/T "Steel Pressure Vessels" GB 150 "Fasteners-Clearance Holes and Counterbores" GB/T 152.1~152.4 "Carbon Structural Steels" GB/T 700 "Hot-rolled Quality Carbon Structural Steel Plates and Wide Strips" GB/T 711 "Steel Plates for Boiler and Pressure Vessels" GB 713 "Hot-rolled Plates and Strips of Carbon Structural Steels and High Strength Low Alloy Structural Steels" GB/T 3274 "Low Alloy Steel Plates for Low Temperature Pressure Vessels" GB 3531 "Hot Rolled Stainless Steel Plate Sheet and Strip" GB/T 4237 "Pipe Threads with 55 Degree Thread Angle where Pressure-tight Joints are Made on the Threads--Part 2.Taper Internal and External Threads" GB/T 7306.2 "General Purpose Industrial Valves-Specification of Carbon Steel Forgings" GB/T 12228 "General Purpose Industrial Valves-Specification of Carbon Steel Castings" GB/T 12229 "General Purpose Industrial Valve-Specification of Stainless Steel Castings" GB/T 12230 3.1 Flange type 3.1.1 The flange type and its code are in accordance with those specified in Figure 3.1.1 and Table 3.1.1.Flange type includes. Slip On Neck Flange, Weld Neck Flange, Integral Type Flange, Socket Welding Flange, Thread Flange, Butt Welding Ring Loose Flange, Long Welding Neck Flange and Blind Flange. 3.1.2 The orifice flange for flow measurement complies with the provisions of Appendix A of this Standard. 3.1.3 The jacket flange for full jacket pipe connection may refer to the requirements of Appendix B of this Standard. 3.1.4 The nominal dimension and nominal pressure applied for flange types are in accordance with those specified in Table 3.1.4. 4.Materials 4.0.1 Materials for steel pipe flange comply with the requirements of Table 4.0.1, its chemical composition, mechanical property and other technical requirement shall be in accordance with the standards provisions listed in Table 4.0.1. 4.0.3 The flanges (excluding blind flanges) shall be made of forgings (or forging rolling technology) and casting (steel), but shall not be tailor-welding. The blind flanges may be made of steel plate. 4.0.4 Unless otherwise specified in this Standard, the materials for pipe flange shall also comply with the requirements of relevant standards and codes. 5.Gaskets and bolting for flange 5.0.1 The gasket shall comply with the sealing property of flange joint under working conditions. Acting by pretension load of bolt, gasket stress under pretension and working conditions shall be ensured, and no deleterious deformation and crush can be generated. 5.0.2 The gasket complies with the requirements of HG/T 20627~HG/T 20635. 5.0.3 The bolting includes hexagon head bolt, full thread stud and nut, the applied bolt quantity and specification are in accordance with the requirements of Table 8.1.1 shown in this Standard. 6.Fitting of flange joint The fitting between the flanges and gaskets complies with the requirements of HG/T 20635. 7.Pressure-temperature rating 7.0.1 For the steel pipe flange and blind flange with nominal pressure grade of Classl50~Class2500, the maximum allowable working pressure under working temperature complies with the requirements of Table 7.0.1-1~Table 7.0.1-16. 7.0.2 The types of pipe flange materials listed in Table 7.0.1-1~Table 7.0.1-16 comply with the requirements of Table 4.1 of this Standard. 7.0.3 The working temperature refers to the temperature of flange metal under pressure effect. When the working temperature is lower than 20��, the maximum allowable working pressure of the flange is identical to that when the temperature is 20��. When the working temperature is higher than the upper temperature limit listed in the table, the maximum allowable working pressure may be determined by the designer proper according to the service experience or calculation. 7.0.4 If the two flanges on the same flange joint have different pressure rated value, the maximum allowable working pressure of the joint fitting is based on the smaller value, moreover, the torsion moment of the stud shall be controlled when installing, so as to prevent high strung. 8.Dimensions 8.1 Coupling dimension of the pipe flange 8.1.1 The coupling dimension of the flange is in accordance with those specified in Figure 8.1.1 and Table 8.1.1 (they are pipe flanges have different pressure grades within mourning border of Table 8.1.1, but they are equipped with same coupling dimension). The domestic and international pipe flanges standards assorted with this Standard may refer to Appendix D of this Standard. 8.1.2 The bolt holes shall be divided in uniformly spaces. 8.2 Physical dimension of the pipe flange 8.2.1 The dimension of slip on neck flange sees Figure 8.2.1 and Table 8.2.1-1~Table 8.2.1-5. 8.2.2 The dimension of the weld neck flange sees Figure 8.2.2 and Table 8.2.2-1~Table 8.2.2-6. 8.2.6 The dimension of thread flange sees Figure 8.2.6 and Table 8.2.6-1~Table 8.2.6-2. 8.2.7 The dimension of the butt welding ring loose flange sees Figure 8.2.7 and Table 8.2.7-1~Table 8.2.7-3. 8.2.8 The dimension of the blind flange sees Figure 8.2.8 and Table 8.2.8-1~Table 8.2.8-6. 8.3 Pipe flange neck 8.3.1 The outer side slope of the slip on neck flange, socket welding flange, thread flange and slip-on flange neck shall be no greater than 7��. 8.3.2 The taper neck slope of the weld neck flange shall be no greater than 45��, and shall be possessed with straight section in slope of no greater than 7��, in which the straight section length is no less than 7mm. 8.3.3 The neck thickness S of the weld neck flange is generally no less than the nominal thickness of the steel pipe, and the user shall indicate that when ordering. S value listed in this Standard is only applicable to occasions that without specific requirements proposed by the users. 8.4.3 The pipe thread shall be concentric with the axial line of the flange hole, and the deviation shall not be more than 5mm/m. 8.4.4 Class150 (PN20) thread flange will not process the locating hole. On the flange neck end, the locating hole shall be chamfered, the angle between the chamfer and the thread axis is about 45��, and the chamfer shall be coaxial with the thread. 9.Welding joint and groove dimension 9.0.1 The welding joint of slip on neck flange connecting to the steel pipe shall comply with the requirements of Figure 9.0.1. 9.0.2 The welding joint of socket welding flange connecting to the steel pipe shall comply with the requirements of Figure 9.0.2. 9.0.3 The welding end and groove dimension of the weld neck flange connecting the steel pipe shall comply with the requirements of Figure 9.0.3-1. 9.0.4 The welding joint and groove dimension of the butt welding ring (slip-on flange) connecting to the steel pipe shall comply with the requirements of Figure 9.0.4. 10.Dimension tolerance 10.0.1 The dimension tolerance of the flanges is in accordance with those specified in Table 10.0.1-1 and Table 10.0.1-2. 10.0.2 The dimension tolerance of the seal contact face of the ring joint face is in accordance with those specified in Table 10.0.2.The hardness of the seal contact face of the flange ring groove shall be higher than the hardness of the assorted metal ring gasket. 10.0.3 The dimension tolerance of the groove at the flange (including butt welding ring) end complies with the requirements of Chapter 9 of this Standard. ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of HG/T 20615-2009 be delivered?Answer: The full copy PDF of English version of HG/T 20615-2009 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of HG/T 20615-2009_English with my colleagues?Answer: Yes. The purchased PDF of HG/T 20615-2009_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- HG/T 20615-2009 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.Question 5: Should I purchase the latest version HG/T 20615-2009?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version HG/T 20615-2009 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically.How to buy and download a true PDF of English version of HG/T 20615-2009?A step-by-step guide to download PDF of HG/T 20615-2009_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "HG/T 20615-2009". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
