GB/T 5800.1-2012 English PDFUS$234.00 ยท In stock
Delivery: <= 3 days. True-PDF full-copy in English will be manually translated and delivered via email. GB/T 5800.1-2012: Rolling bearings -- Instrument precision bearings -- Part 1: Boundary dimensions, tolerances and characteristics of metric series bearings Status: Valid GB/T 5800.1: Historical versions
Basic dataStandard ID: GB/T 5800.1-2012 (GB/T5800.1-2012)Description (Translated English): Rolling bearings -- Instrument precision bearings -- Part 1: Boundary dimensions, tolerances and characteristics of metric series bearings Sector / Industry: National Standard (Recommended) Classification of Chinese Standard: J11 Classification of International Standard: 21.100.20 Word Count Estimation: 12,126 Older Standard (superseded by this standard): GB/T 5800-2003 Quoted Standard: GB/T 6930-2002; ISO 15; ISO 582; ISO 1132-1; ISO 15241 Adopted Standard: ISO 1224-1-2007, IDT Regulation (derived from): National Standards Bulletin No. 24 of 2012 Issuing agency(ies): General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China, Standardization Administration of the People's Republic of China Summary: This standard specifies the metric series bearings with a precision instrument type, dimensions, tolerances and clearance for optional grouping, moments define and test conditions, and bearing yield ratio limits and other characteristics. GB/T 5800.1-2012: Rolling bearings -- Instrument precision bearings -- Part 1: Boundary dimensions, tolerances and characteristics of metric series bearings---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order. ICS21.100.20 J11 National Standards of People's Republic of China GB/T 5800.1-2012/ISO 1224-1.2007 Partial replacement of GB/T 5800-2003 Rolling instrument precision bearings Part 1. Metric series bearing dimensions, Tolerances and characteristics Part 1. Boundarydimensions, tolerancesandcharacteristicsof (ISO 1224-1.2007, IDT) Issued on. 2013-03-01 2012-09-03 implementation Administration of Quality Supervision, Inspection and Quarantine of People's Republic of China Standardization Administration of China released ForewordGB/T 5800 "Rolling instrument precision bearings" is divided into two parts. --- Part 1. Metric series bearing dimensions, tolerances and characteristics; --- Part 2. Inch series bearings dimensions, tolerances and characteristics. This is Part 1 GB/T 5800's. Rules in this section in accordance with GB/T 1.1-2009 given draft. This Part replaces GB/T 5800-2003 content "Rolling instrument precision bearings" Metric series section, and GB/T 5800- Compared to 2003, in addition to editorial changes outside the main technical changes are as follows. --- Deleted the contents of inch series bearings (see 2003 edition of the Table 3, Table 4, Table 9 and Table 10, Tables 5 to 8 and 11 Part of the contents); --- Modify some of the terms and definitions (see 31, 2003, version 3.1.); --- Modify some symbols (see Chapter 4, 2003 edition of the Table 1); --- Increasing the angular contact ball bearing structure schematic diagram [see Figure 1b)]; --- Modify the inner end face of the vertical bore (Sd) formula (see Table 2 and Table 4, 2003 edition of the tables 5 and 7). This section uses the translation method identical with ISO 1224-1.2007 "Rolling Instrument precision bearings - Part 1. Metric series Bearing dimensions, tolerances and characteristics. " Consistency correspondence between this part of international documents and normative references of our files are as follows. --- GB/T 273.3-1999 Rolling bearings dimensions, general plan (eqvISO 15.1998) --- GB/T 274-2000 Rolling chamfer dimensions Max (idtISO 582.1995) --- GB/T 4199-2003 Rolling defined tolerances (ISO 1132-1.2000, MOD) --- GB/T 7811-2007 Rolling Parameter Symbol (ISO 15241.2001, IDT) This part is proposed by China Machinery Industry Federation. This part of the National Standardization Technical Committee of Rolling (SAC/TC98) centralized. This section is drafted. Luoyang Bearing Research Institute Co., Ltd., Zhongshan City, Pacific Century Bearing Manufacturing Co., Ltd. The main drafters of this section. Song Yucong, Bing, Chen Qingxi, Chen Taiping. This section instead of the metric part GB/T 5800-2003 of. The previous versions of GB/T 5800 release case. --- GB 5800-1986, GB/T 5800-2003. GB/T 5800.1-2012/ISO 1224-1.2007 Rolling instrument precision bearings Part 1. Metric series bearing dimensions, Tolerances and characteristics1 ScopeThis section GB/T 5800 provisions of the instrument precision metric series bearing type, dimensions, tolerances and clearance for the optional Grouping, torque and define test conditions and the bearing limits the yield ratio and other characteristics.2 Normative referencesThe following documents for the application of this document is essential. For dated references, only the dated edition applies to this article Member. For undated references, the latest edition (including any amendments) applies to this document. GB/T 6930-2002 Rolling vocabulary (ISO 5593.1997) ISO 15 Rolling bearings dimensions, general plan (Rolingbearings-Radialbearings-Boundary dimensions, generalplan) ISO 582 Rolling maximum chamfer dimensions (Rolingbearings-Chamferdimensions-Maximumval- ues) ISO 1132-1 Rolling tolerances - Part 1. Terms and definitions (Rolingbearings-Tolerances-Part 1. Termsanddefinitions) ISO 15241 Rolling Parameter Symbol (Rolingbearings-Symbolsforquantities)3 Terms and DefinitionsAnd the following terms and definitions GB/T 6930 and ISO 1132-1 defined apply to this document. 3.1 The inner circle of the hole on the end face of verticality perpendicularityofinnerringborewithrespecttotheface < Basic cylindrical surface> radially inner tangential reference plane parallel to the end face, the maximum axial single chamfer at both ends from the inner surface of 1.2 times , Bore the same points total online prime amount of variation in the relative size of the position. 3.2 Assembled bearing outer ring flange on the back of axial runout axialrunoutofouterringflangebackfaceofassembledbearing < Type groove radial ball bearings> in the radial distance from the axis of the outer ring at the back of the flange equal to half the average diameter of the outer ring flange on the back of the outer Circle different angular positions relative to the inner axial difference between the maximum and minimum distance between a fixed point. Note. In order to measure the effective inner and outer ring raceway should be in contact with all the balls. 3.3 Torque nature torquequality The average torque means the instrument ball bearings and maximum torque. NOTE. In the low (near zero) or operating restrictions radian commonly expressed when the maximum torque is available at a certain speed torque average judge. GB/T 5800.1-2012/ISO 1224-1.2007 ......Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of GB/T 5800.1-2012_English be delivered?Answer: Upon your order, we will start to translate GB/T 5800.1-2012_English as soon as possible, and keep you informed of the progress. The lead time is typically 1 ~ 3 working days. The lengthier the document the longer the lead time.Question 2: Can I share the purchased PDF of GB/T 5800.1-2012_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 5800.1-2012_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay.Question 5: Should I purchase the latest version GB/T 5800.1-2012?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 5800.1-2012 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically. |
