GB/T 38216.2-2019 PDF EnglishUS$140.00 · In stock · Download in 9 seconds
GB/T 38216.2-2019: Steel slag - Determination of fluoride content and chloride content - Ion chromatography Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid
Similar standardsGB/T 38216.2-2019: Steel slag - Determination of fluoride content and chloride content - Ion chromatography---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT38216.2-2019 GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 77.140.99 H 34 Steel slag - Determination of fluoride content and chloride content - Ion chromatography ISSUED ON: OCTOBER 18, 2019 IMPLEMENTED ON: FEBRUARY 01, 2020 Issued by: State Administration for Market Regulation; Standardization Administration of the People's Republic of China. Table of ContentsForeword ... 3 1 Scope ... 4 2 Normative references ... 4 3 Principle ... 5 4 Reagents and materials ... 5 5 Instruments and equipment... 6 6 Sample preparation ... 7 7 Test steps ... 7 8 Calculation of test results ... 8 9 Precision ... 9 10 Test report ... 9 Annex A (normative) Flow chart of specimen analysis result acceptance procedure ... 11 Annex B (informative) Experimental raw data ... 12 Steel slag - Determination of fluoride content and chloride content - Ion chromatography WARNING - Personnel using this Part shall have formal laboratory work experience. This Part does not point out all possible security issues. The user is responsible for taking appropriate safety and health measures and ensuring compliance with the conditions stipulated by relevant national laws and regulations.1 ScopeThis Part of GB/T 38216 specifies the method to determine the content of fluorine and chlorine in steel slag by ion chromatography. This Part is applicable to the determination of fluorine and chlorine content in steel slag. Determination range (mass fraction): 0.05%~2.0% for fluorine, 0.005%~0.1% for chlorine.2 Normative referencesThe following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. GB/T 2007.2, General rules for the sampling and sample preparation of minerals in bulk-Manual method of sample preparation GB/T 6682, Water for analytical laboratory use - Specification and test methods GB/T 8170, Rules of rounding off for numerical values & expression and judgement of limiting values GB/T 12806, Laboratory glassware - One-mark volumetric flasks GB/T 12807, Laboratory glassware - Graduated pipettes GB/T 12808, Laboratory glassware - One-mark pipettes GB/T 36240-2018, Ion chromatographs3 PrincipleThe specimen is decomposed by sulfuric acid. Fluorine and chlorine escape with water vapor and separate from the sample. It is absorbed by absorption liquid. Use ion chromatography to determine. Qualitatively determine fluorine and chlorine by the peak time. Use the standard curve to quantitatively determine.4 Reagents and materialsUnless otherwise specified, the reagents used are guaranteed reagents, and the experimental water is grade one water specified in GB/T 6682. 4.1 Sodium hydroxide. 4.2 Sodium fluoride, the reference substance. 4.3 Sodium chloride, the reference substance. 4.4 Concentrated sulfuric acid, ρ=1.84g/mL. 4.5 Sulfuric acid solution (2+1): Measure 200mL of concentrated sulfuric acid (see 4.4) and slowly pour into 100mL of water. Mix well. 4.6 Sodium hydroxide solution c(NaOH)=0.2mol/L: Weigh 8.0g of sodium hydroxide (see 4.1) and dissolve it in 1000mL of water. 4.7 Fluorine standard stock solution: Accurately weigh 2.2110g of standard sodium fluoride that has been dried at 105°C±2°C for 2h (see 4.2). Use water to dissolve. Transfer to a 1000mL volumetric flask. Use water to dilute to the scale mark. Mix well. Transfer to a dry plastic bottle for storage. 1mL of this solution contains 1000μg of fluorine. 4.8 Chlorine standard stock solution: Accurately weigh 1.6485g of reference sodium chloride that has been burned to constant weight at 500°C~600°C (see 4.3). Dissolve in water. Transfer to a 1000mL volumetric flask. Use water to dilute to the scale mark. Shake well. 1mL of this solution contains 1000μg of chlorine. 4.9 Fluorine and chlorine mixed standard solution: Accurately pipette 5.00mL of fluorine standard storage solution and chlorine standard storage solution respectively (see 4.7 and 4.8) into a 50mL volumetric flask. Use water to dilute to the scale mark. 1mL of this solution contains 100.0μg of fluorine or chlorine respectively. 5.8 Glassware: All glassware must be soaked in 2mol/L sodium hydroxide solution and water for 4h before use. Then use water to rinse 3~5 times. Let dry and set aside. 5.9 The volumetric flask shall meet the requirements of GB/T 12806. The pipette shall meet the requirements of GB/T 12807 and GB/T 12808.6 Sample preparationPrepare the specimen according to the method in GB/T 2007.2. The particle size of the specimen is not greater than 0.080mm. Place the sieved specimen in an oven (see 5.1) at 105°C±2°C for 1h. Take it out. Place it in a desiccator to cool to room temperature for future use.7 Test steps7.1 Specimen amount Weigh 0.5g of specimen, to the nearest of 0.0001g. 7.2 Number of determinations For the same specimen, conduct at least two independent determinations. 7.3 Blank test Do a blank test with the specimen. 7.4 Chromatographic analysis conditions Debug the parameters such as chromatographic column temperature, elution speed, suppression current, injection volume. Set aside for future use. 7.5 Determination 7.5.1 Take an appropriate amount of water and place it in the distillation flask of the steam distillation device (see 5.4). Heat to make water boil, for future use. 7.5.2 Pipette 10mL of sodium hydroxide solution (see 4.6) into a 100mL receiving bottle as the receiving solution, for future use. 7.5.3 Place the test material (see 7.1) in a three-necked round bottom flask. Add 60mL of sulfuric acid solution (see 4.5). Use water to clean the mouth of the bottle. Put in a few glass beads. Connect steam distillation device for distillation. Heating makes the temperature of the solution in the three-neck ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 38216.2-2019 be delivered?Answer: The full copy PDF of English version of GB/T 38216.2-2019 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 38216.2-2019_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 38216.2-2019_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 38216.2-2019 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.How to buy and download a true PDF of English version of GB/T 38216.2-2019?A step-by-step guide to download PDF of GB/T 38216.2-2019_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 38216.2-2019". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
