GB/T 37213-2018 English PDFUS$139.00 ยท In stock
Delivery: <= 3 days. True-PDF full-copy in English will be manually translated and delivered via email. GB/T 37213-2018: Test method for silicon brick dimension -- Laser technology method Status: Valid
Basic dataStandard ID: GB/T 37213-2018 (GB/T37213-2018)Description (Translated English): Test method for silicon brick dimension -- Laser technology method Sector / Industry: National Standard (Recommended) Classification of Chinese Standard: H21 Classification of International Standard: 77.040 Word Count Estimation: 7,731 Date of Issue: 2018-12-28 Date of Implementation: 2019-11-01 Regulation (derived from): National Standard Announcement No. 17 of 2018 Issuing agency(ies): State Administration for Market Regulation, China National Standardization Administration GB/T 37213-2018: Test method for silicon brick dimension -- Laser technology method---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order.Test method for silicon brick dimension--Laser technology method ICS 77.040 H21 National Standards of People's Republic of China Silicon ingot size measurement laser method Published on.2018-12-28 2019-11-01 implementation State market supervision and administration China National Standardization Administration issued ForewordThis standard was drafted in accordance with the rules given in GB/T 1.1-2009. This standard is supported by the National Semiconductor Equipment and Materials Standardization Technical Committee (SAC/TC203) and National Semiconductor Equipment and Materials Standards. The Technical Subcommittee Materials Branch (SAC/TC203/SC2) jointly proposed and managed. This standard was drafted. Suzhou GCL Solar Technology Co., Ltd., Jiangsu Xiexin Silicon Materials Technology Development Co., Ltd., Shandong Daxin Energy Source Development Co., Ltd. The main drafters of this standard. Gong Longfei, Jin Shanming, Lin Qingxiang, Xiage Genping, Tang Shanshan, Liu Kun. Silicon ingot size measurement laser method1 ScopeThis standard specifies methods for non-contact measurement of square silicon ingot size by laser method, including diagonal, chamfer, perpendicularity, side length and length. This standard applies to the measurement of the size of a square silicon ingot cut by a silicon single crystal rod or a polycrystalline silicon ingot in the semiconductor and photovoltaic fields.2 Normative referencesThe following documents are indispensable for the application of this document. For dated references, only the dated version applies to this article. Pieces. For undated references, the latest edition (including all amendments) applies to this document. GB/T 14264 semiconductor material terminology GB/T 25076 silicon single crystal for solar cells GB/T 29054 solar grade cast polycrystalline silicon block3 Terms and definitionsThe terms and definitions defined in GB/T 14264, GB/T 25076 and GB/T 29054 apply to this document.4 Principle of the methodA size measurement system is constructed using laser technology, and a laser source is used as the incident light to illuminate the silicon ingot. Receiving a laser through a laser probe The light reflects the signal, forms a laser pulse waveform, and feeds the data back to the computer software processing control system. Control by computer software The system simulates and calculates the diagonal, chamfer, perpendicularity, side length and length parameters of the silicon ingot to obtain the dimensional parameters of the silicon ingot. The diagonal, chamfer, and perpendicularity parameters of the silicon ingot are measured by the laser measuring components A, B, C, and D, as shown in FIG. Silicon ingot side length, length The parameters are measured by the laser measuring components P, L, Q, R, as shown in Figure 2. When measuring the length of a silicon ingot, the silicon ingot is perpendicular to the laser measuring component. Surface movement, when the first end face of the silicon ingot passes through the laser to measure the plane of the component, the initial position of the four sides is recorded, when the second end of the silicon ingot passes When the laser is used to measure the plane of the component, the end positions of the four sides are recorded to determine the length of the silicon ingot. Description. A, B, C, D---laser measurement components. Figure 1 Schematic diagram of diagonal, chamfer and perpendicularity measurement of silicon ingot ......Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of GB/T 37213-2018_English be delivered?Answer: Upon your order, we will start to translate GB/T 37213-2018_English as soon as possible, and keep you informed of the progress. The lead time is typically 1 ~ 3 working days. The lengthier the document the longer the lead time.Question 2: Can I share the purchased PDF of GB/T 37213-2018_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 37213-2018_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay. |
