GB/T 35785-2017 PDF EnglishUS$85.00 · In stock · Download in 9 seconds
GB/T 35785-2017: Specification for the Installation of Read-Write Equipment of the Electronic Identification of motor Vehicles Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid
Similar standardsGB/T 35785-2017: Specification for the Installation of Read-Write Equipment of the Electronic Identification of motor Vehicles---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT35785-2017 GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 35.240.15 T 35 Specification for the Installation of Read-Write Equipment of the Electronic Identification of motor Vehicles Issued on: DECEMBER 29, 2017 Implemented on: JULY 01, 2018 Issued by. General Administration of Quality Supervision, Inspection and Quarantine; Standardization Administration of PRC. Table of ContentsForeword ... 3 1 Scope ... 4 2 Normative References ... 4 3 Terms and Definitions ... 4 4 Installation ... 4 4.1 Installation environment ... 4 4.2 Installation requirements ... 5 4.3 Installation mode ... 5 4.4 Installation quantity ... 5 4.5 Installation location ... 5 4.6 Installation height ... 6 4.7 Feeder unit ... 6 4.8 Member bar ... 6 4.9 Other requirements ... 7 5 Acceptance ... 7 5.1 Test conditions on the acceptance site ... 7 5.2 Installation and acceptance ... 8 5.3 Functional compliance inspection ... 8 Appendix A (Normative) Installation Mode Schematic Diagram ... 9 Appendix B (Normative) Installation Location Schematic Diagram ... 13 Appendix C (Normative) Notification Sign ... 14 Bibliography ... 15 Specification for the Installation of Read-Write Equipment of the Electronic Identification of motor Vehicles1 ScopeThis Standard specifies the installation and acceptance for read-write equipment of the electronic identification of stationary motor vehicles. This Standard is applicable to the installation and acceptance for read-write equipment of the electronic identification of stationary motor vehicles.2 Normative ReferencesThe following documents are essential to the application of this document. For the dated documents, only the versions with the dates indicated are applicable to this document; for the undated documents, only the latest version (including all the amendments) are applicable to this document. GB/T 35786-2017 General Specification for Read-Write Equipment of the Electronic Identification of Motor Vehicles GB 50198-2011 Technical Code for Project of Civil Closed Circuit Monitoring Television System3 Terms and DefinitionsThe terms and definitions stipulated in GB/T 35786-2017 are applicable to this document.4 Installation4.1 Installation environment The installation location of the read-write equipment shall meet the following requirements. identification lane centerline; c) When the antenna unit of separated read-write equipment or integrated read- write equipment are installed on the roadside, the angle between the horizontal project of antenna element normal line and the direction of travel shall be no greater than 30°, which can refer to Appendix B. 4.6 Installation height The installation height of read-write equipment outdoors shall meet the following requirements. a) When installed on the pole, the clearance height shall be greater than or equal to 2.5m; b) When installed on the crossbar, the clearance height shall be greater than or equal to 5.5m; c) When installed in bridge, tunnel, culvert, etc., the clearance height shall be no lower than the road height limit; d) The clearance height of antenna unit shall be no greater than 7m. 4.7 Feeder unit The bending radius of the feeder unit of the separated read-write equipment shall be greater than 15 times of the outer diameter of the feeder cable; the bending position shall be smooth and uniform, no repeatedly bending is allowed; the feeder shall not be wrapped or twisted but laid smoothly and straight. 4.8 Member bar The installation of member bar shall meet the following requirements. a) It is advisable to use circular or polyhedral variable section profiles to make; the connection between the pole and crossbar shall be welded the fixed flange plate; at least 4 reinforcing ribs shall be welded between the flange plate and rod; b) The threading holes shall be left at 0.3m~1.0m from the pole to the ground; waterproof screed, cover plate and fixed screws shall be equipped with; c) The installation locates of read-write unit and antenna unit shall be reserved outlet holes; the rubber sheath, cable backwater trap hook shall be equipped with; d) Install the plastic or anti-corrosion-treated metal waterproof cap on the top of the pole; while the bottom shall be welded the fixed flange plate; at least 4 reinforcing ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 35785-2017 be delivered?Answer: The full copy PDF of English version of GB/T 35785-2017 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 35785-2017_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 35785-2017_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 35785-2017 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.How to buy and download a true PDF of English version of GB/T 35785-2017?A step-by-step guide to download PDF of GB/T 35785-2017_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 35785-2017". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
