GB/T 34445-2017 English PDFUS$179.00 ยท In stock
Delivery: <= 3 days. True-PDF full-copy in English will be manually translated and delivered via email. GB/T 34445-2017: Test method of hot-tack property for heat sealing surfaces of thermoplastic polymer and thermoplastic composite material Status: Valid
Basic dataStandard ID: GB/T 34445-2017 (GB/T34445-2017)Description (Translated English): Test method of hot-tack property for heat sealing surfaces of thermoplastic polymer and thermoplastic composite material Sector / Industry: National Standard (Recommended) Classification of Chinese Standard: G31 Classification of International Standard: 83.080.20 Word Count Estimation: 9,938 Date of Issue: 2017-09-29 Date of Implementation: 2018-04-01 Quoted Standard: GB/T 2918-1998 Regulation (derived from): National Standard Notice 2017 No. 23 Issuing agency(ies): General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China, Standardization Administration of the People's Republic of China Summary: This standard specifies the terms and definitions, principles and methods of determination of thermal hot tack properties of thermoplastics and their composites overview, sample, sample conditioning, equipment, test procedures, test results, test reports. This standard applies to flexible thermoplastics and their composites, from the end of the heat seal to the heat sealing part has not yet cooled to ambient temperature within a specific time interval, under different heat seal conditions of hot tack performance test. GB/T 34445-2017: Test method of hot-tack property for heat sealing surfaces of thermoplastic polymer and thermoplastic composite material---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order. Test method of hot-tack property for heat sealing surfaces of thermoplastic polymer and thermoplastic composite material ICS 83.080.20 G31 National Standards of People's Republic of China Thermoplastics and their composite heat seals Hot tack performance test 2017-09-29 Posted 2018-04-01 implementation General Administration of Quality Supervision, Inspection and Quarantine of People's Republic of China China National Standardization Administration released ForewordThis standard was drafted in accordance with the rules given in GB/T 1.1-2009. This standard proposed by the China Light Industry Federation. This standard by the National Plastics Standardization Technical Committee (SAC/TC48) centralized. This standard was drafted. Haidian District, Beijing Institute of Product Quality Supervision, Jinan Lan Kwong Electrical Technology Co., Ltd. Xiamen Shunfeng packaging Materials Co., Ltd., Xiamen Kindness Packing Co., Ltd., Guangdong Tak crown packaging materials Limited. The main drafters of this standard.Wang Zhaohui, Jiang Yunzhong, Chen Xin, Xu Wenshu, Luo Yufeng, Guo Jianxin, Wang Ronggui, Cai Huageng. Thermoplastics and their composite heat seals Hot tack performance test1 ScopeThis standard specifies the terms and definitions, principles and methods of thermosensitive properties of thermoplastics and their composite materials, Sample, sample conditioning, equipment, test procedures, test results, test reports. This standard applies to flexible thermoplastics and their composites, from the end of the heat seal to the heat sealing part has not yet cooled to ambient temperature Timing interval, under different heat sealing conditions of the hot tack test.2 Normative referencesThe following documents for the application of this document is essential. For dated references, only the dated version applies to this article Pieces. For undated references, the latest edition (including all amendments) applies to this document. GB/T 2918-1998 plastic sample conditioning and testing of the standard environment3 Terms and definitionsThe following terms and definitions apply to this document. 3.1 Sealing layer surface separation adhesivefailure Separation behavior occurring at the heat seal interface. 3.2 Failure mode failuremode During the hot-stick test, the heat-seal sample is disconnected when the chuck is separated, as shown in FIG. 1. 3.3 Melting through burnthrough Hot seal at the weld piercing and thermal deformation of the state. Note. When this occurs at the heat seal, the heat seal temperature is too high or the heat seal time is too long. 3.4 Cohesive destruction of cohesivefailure One or both sides of the heat-sealed sample are destroyed at a point approximately parallel to the heat seal interface while the heat seal interface maintains a complete failure mode. Note. The damage mode is shown in Figure 1. When adhesive materials are involved in heat-sealing, a similar term can be defined when similar damage occurs. 3.5 Cooling curve coolingcurve In the heat sealing process just after the end of the thermal viscosity with the cooling time curve, shown in Figure 2. Note that the cooling curve is the curve of the hot tack on the cooling time, and the most practical part of the cooling curve is the first 1 s after the heat sealing knife is opened. 3.6 Cooling time coolingtime The time between the point at which the heat seal knife is separated and the time point at which the hot tack is measured. ......Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of GB/T 34445-2017_English be delivered?Answer: Upon your order, we will start to translate GB/T 34445-2017_English as soon as possible, and keep you informed of the progress. The lead time is typically 1 ~ 3 working days. The lengthier the document the longer the lead time.Question 2: Can I share the purchased PDF of GB/T 34445-2017_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 34445-2017_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay. |
