GB/T 325.1-2018 PDF EnglishUS$150.00 · In stock · Download in 9 seconds
GB/T 325.1-2018: Zinc-coated steel wire ropes for high-pressure rubber hose Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid GB/T 325.1: Historical versions
Similar standardsGB/T 325.1-2018: Zinc-coated steel wire ropes for high-pressure rubber hose---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT325.1-2018GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 55.140 A 82 Replacing GB/T 325.1-2008 Packaging containers - Steel drums - Part 1. General specifications Issued on: MAY 14, 2018 Implemented on: DECEMBER 01, 2018 Issued by. State Market Regulatory Administration; Standardization Administration of PRC. Table of ContentsForeword ... 3 1 Scope ... 5 2 Normative references ... 5 3 Terms and definitions ... 6 4 Classification ... 6 5 Materials ... 8 6 Technical requirements ... 8 7 Test methods ... 10 8 Inspection rules ... 12 9 Marking, packaging, transportation and storage ... 14 Appendix A (Informative) Steel drum internal cleanliness measurement method ... 15 References ... 17 Packaging containers - Steel drums - Part 1. General specifications1 ScopeThis part of GB/T 325 specifies the classification, materials, technical requirements, test methods, inspection rules, marking, packaging, transportation and storage of steel drums. This section applies to the manufacture, circulation, use and supervision & inspection of steel drums.2 Normative referencesThe following documents are essential to the application of this document. For the dated documents, only the versions with the dates indicated are applicable to this document; for the undated documents, only the latest version (including all the amendments) are applicable to this standard. GB/T 325.2 Packaging containers - Steel drums - Part 2. Removable head (open head) drums with a minimum total capacity of 208 L, 210 L and 216.5 GB/T 325.3 Packaging containers - Steel drums - Part 3. Non-removable head (tight head) drums with a minimum total capacity of 212 L, 216.5 L and 230 L GB/T 325.4 Packaging containers - Steel drums - Part 4. Removable head (open head) drums with a maximum total capacity of 200 L GB/T 325.5 Packaging containers - Steel drums - Part 5. Non-removable head (tight head) drums with a maximum total capacity of 200 L GB/T 2518 Continuously hot-dip zinc-coated steel sheet and strip GB/T 2828.1 Sampling procedures for inspection by attributes - Part 1. Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection GB/T 3274 Hot-rolled plates and strips of carbon structural steels and high strength low alloy structural steels5 Materials5.1 Steel plates for steel drums shall comply with the provisions of GB/T 2518, GB/T 3274, GB/T 11253, YB/T 055, and other thin steel plates may be selected in accordance with user requirements. 5.2 The crimping sealing material shall be made of heat-resistant, weather- resistant, durable and dissolving-resistant materials that have good sealing properties and are compatible with the contents. 5.3 The steel drum closure system shall comply with the provisions of GB/T 13251. 5.4 The outer surface coating shall be made of materials with strong adhesion, weather resistance and durability; the inner surface coating shall be made of materials compatible with the contents. 5.5 The crimp sealing packing, closure system and internal coating which are in direct contact with food, food additives or pharmaceuticals shall comply with food safety regulations.6 Technical requirements6.1 Basic requirements 6.1.1 The drum body, the drum head, and the drum bottom shall be made of the entire steel plate and shall not be spliced; the thickness of the steel plate shall meet the strength requirements. 6.1.2 The drum body weld is made by electric resistance welding. 6.1.3 The drum body type can be one of the following. - No ring ribs, no corrugations; - With 2 ring ribs; - There are 3 ~ 7 corrugations at both ends; - There are 2 ring ribs, and there are 3 ~ 7 corrugations from the ring ribs to the drum head and drum bottom. Note. The drum type can be as agreed upon in accordance with user requirements. 6.1.4 The sealing of the drum body and the drum head & bottom shall be filled with sealing packing as required, the type may be one of the following. Use hand touching, visual inspection and general or special gauge for inspection. 7.2 Specifications Use general purpose or special gauges for inspection. 7.3 Weight tolerance Use a gauge with a resolution of not more than 0.05 kg for measurement. 7.4 Airtight test Tight head steel drums are tested in accordance with GB/T 17344. The test conditions are shown in Table 1. Check the sample drum for leakage. 7.5 Hydraulic test This test is limited to tight head steel drums. Fill the drum with water, connect the pressure gauge to the pressure pump, and fix it on the injection port through the connecting parts; pressurize the inside of the drum; after the test pressure is reached, hold the pressure for 5 minutes. See Table 1 for the test conditions and check the sample drum for leakage. 7.6 Stacking test Fill the empty drum with the substance similar to the density of the goods to be transported, in accordance with the provisions of GB/T 4857.3. The test time is 24 h, the steel drum shall not have any deformation or severe damage that may reduce its strength or cause stack instability through inspection. The stacking load is calculated in accordance with formula (1). Where. P - The stacking load imposed on the steel drum container, in Newtons (N); H - Stacking height, in meters (m); Note. The stacking height is 3 m for ground transportation and 8 m for sea transportation. h - The height of a single piece of steel drum, in meters (m); m - The mass of the single-piece steel drum after loading the corresponding items, in kilograms (kg). a) Take 3 sample drums to test the items of 6.1, 6.2 and 6.3, 6.4, 6.6, 6.7, then use these 3 sample drums for airtight test, then use these 3 sample drums for hydraulic test; b) From the remaining 6 sample drums, take 3 sample drums for stacking test, then use these 6 sample drums for the falling test. 8.4 Decision rules 8.4.1 Exit-factory inspection 8.4.1.1 If four or more items of 6.1, 6.2, 6.3, 6.4, 6.6, and 6.7 fail, the sample is judged to be unqualified. When the airtight test in Table 1 fails, the sample is judged unqualified. 8.4.1.2 When the number of unqualified samples is greater than or equal to the number of failures specified in Tables 4 and 5, the batch is judged to be unqualified. 8.4.2 Type inspection 8.4.2.1 If four or more items of 6.1, 6.2, 6.3, 6.4, 6.6, and 6.7 are unqualified, the sample is judged to be unqualified; if one of the samples fails, the batch is judged to be unqualified. 8.4.2.2 If one of the items in Table 1 fails, the sample is judged to be unqualified; if one of the samples fails, the batch is judged to be unqualified.9 Marking, packaging, transportation and storage9.1 Marking There shall be markings on the steel drum, including. the name or code of the manufacturer, the date of manufacture, and the thickness of the steel plate. 9.2 Packaging The drum is packaged in a container, tray or as agreed by the user. 9.3 Transportation Avoid bumps, falls and rolling during transportation and handling. 9.4 Storage Steel drums should not be stacked in a humid, corrosive atmosphere or in the open air. When stacking, the bottom layer shall be cushioned. ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 325.1-2018 be delivered?Answer: The full copy PDF of English version of GB/T 325.1-2018 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 325.1-2018_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 325.1-2018_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 325.1-2018 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.Question 5: Should I purchase the latest version GB/T 325.1-2018?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 325.1-2018 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically.How to buy and download a true PDF of English version of GB/T 325.1-2018?A step-by-step guide to download PDF of GB/T 325.1-2018_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 325.1-2018". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
