GB/T 30202.3-2013 English PDFUS$139.00 · In stock
Delivery: <= 3 days. True-PDF full-copy in English will be manually translated and delivered via email. GB/T 30202.3-2013: Test method for granular coal-based activated carbon for desulfurization and denitration process -- Part 3: Abrasive resistance and compression strength Status: Valid
Basic dataStandard ID: GB/T 30202.3-2013 (GB/T30202.3-2013)Description (Translated English): Test method for granular coal-based activated carbon for desulfurization and denitration process -- Part 3: Abrasive resistance and compression strength Sector / Industry: National Standard (Recommended) Classification of Chinese Standard: D24 Classification of International Standard: 75.160.10 Word Count Estimation: 6,660 Regulation (derived from): National Standards Bulletin 2013 No. 27 Issuing agency(ies): General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China, Standardization Administration of the People's Republic of China Summary: This standard specifies the use of coal desulfurization and denitrification wear and granular activated carbon (hereinafter referred to as active coke), measurement principle compressive strength, measured steps and calculations and other content. This st GB/T 30202.3-2013: Test method for granular coal-based activated carbon for desulfurization and denitration process -- Part 3: Abrasive resistance and compression strength---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order. Test method for granular coal-based activated carbon for desulfurization and denitration process Part 3.. Abrasive resistance and compression strength ICS 75.160.10 D24 National Standards of People's Republic of China Granular activated carbon coal quality test methods for desulfurization and denitrification Part 3. abrasion resistance, compressive strength denitrationprocess-Part 3. Abrasiveresistanceandcompressionstrength Issued on. 2013-12-31 2014-10-01 implementation Administration of Quality Supervision, Inspection and Quarantine of People's Republic of China Standardization Administration of China released ForewordGB/T 30202 "desulphurization and denitrification granular activated carbon from coal test method" is divided into five sections. --- Part 1. bulk density; --- Part 2. particle size; --- Part 3. abrasion resistance, compressive strength; --- Part 4. desulfurization value; --- Part 5. denitration rate. This section GB/T Part of 330,202. This section drafted in accordance with GB/T 1.1-2009 given rules. This section proposed and managed by China North Industries Group Corporation. This section is drafted. Shanxi Xinhua Chemical Co., Ltd. The main drafters of this section. Chi Kwong Sau, Leixue Qing, Zhang Xu, LI Huai-beads, Pang Huisheng PROCEEDINGS OF THE Ni Ping, Yang Jing. Granular activated carbon coal quality test methods for desulfurization and denitrification Part 3. abrasion resistance, compressive strength1 ScopeThis section GB/T 30202 specifies the desulfurization and denitration wear, measured from coal granular activated carbon (hereinafter referred to as activated coke) of compressive strength Set theory, measurement procedures and results of the calculation and so on. This section applies to the determination of activated coke abrasion resistance and compressive strength.2 Principle of Measurement2.1 abrasion resistance Under certain conditions, the sample was placed on a certain withstand mechanical wear within the instrument, remove the sample were sieved sample mass accounted onsize The total sample mass percentage of abrasion resistance. 2.2 Compressive strength The focus is placed on the active biasing compressive strength tester, record activated coke is crushed by the instantaneous force value is calculated a predetermined number of activated coke level Compressive strength is governed by force.3 instruments and equipment3.1 wear strength tester, the number of revolutions of the drum (50 ± 2) r/min, the inner diameter of 200mm, the effective length of 70mm, the inner wall has a symmetrical Two baffles, the baffle height 30mm, thickness 3mm ~ 4mm, length 70mm. 3.2 compressive strength tester, upper and lower clamps shall conform to Figure 1, Figure 2 predetermined pressure column diameter 6.1 0.05 0.00mm, pressure gauge range 0 ~ 10kN, test speed 100mm/min ~ 120mm/min. Millimeters Figure 1 on the jig (pressure column) schematic ......Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of GB/T 30202.3-2013_English be delivered?Answer: Upon your order, we will start to translate GB/T 30202.3-2013_English as soon as possible, and keep you informed of the progress. The lead time is typically 1 ~ 3 working days. The lengthier the document the longer the lead time.Question 2: Can I share the purchased PDF of GB/T 30202.3-2013_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 30202.3-2013_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay. |
