GB/T 24962-2010 English PDFUS$579.00 · In stock
Delivery: <= 5 days. True-PDF full-copy in English will be manually translated and delivered via email. GB/T 24962-2010: Refrigerated hydrocarbon liquids -- Static measurement -- Calculation procedure Status: Valid
Basic dataStandard ID: GB/T 24962-2010 (GB/T24962-2010)Description (Translated English): Refrigerated hydrocarbon liquids -- Static measurement -- Calculation procedure Sector / Industry: National Standard (Recommended) Classification of Chinese Standard: E24 Classification of International Standard: 75.060 Word Count Estimation: 25,210 Date of Issue: 2010-08-09 Date of Implementation: 2010-12-01 Quoted Standard: GB/T 1885-1998; GB/T 11062-1998 Adopted Standard: ISO 6578-1991, MOD Regulation (derived from): National Standard Approval Announcement 2010 No.3 (Total No.158) Issuing agency(ies): General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China, Standardization Administration of the People's Republic of China Summary: This standard specifies the Refrigerated light hydrocarbon fluids such as LNG (liquefied natural gas) and LPG (liquefied petroleum gas), measured under the conditions of the volume translated into a liquid or vapor volume at standard temperature and pressure conditions of the reference equivalent, or translated into equivalent mass or energy (heat) is calculated. This standard applies to static storage conditions Refrigerated light hydrocarbon liquid level gauge measurements stored in the tank, or transferred from the tank, or metered into the tank during the transfer. GB/T 24962-2010: Refrigerated hydrocarbon liquids -- Static measurement -- Calculation procedure---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order.Refrigerated hydrocarbon liquids. Static measurement. Calculation procedure ICS 75.060 E24 National Standards of People's Republic of China Frozen hydrocarbon fluids Static measurement calculation method (ISO 6578.1991, MOD) Issued on. 2010-08-09 2010-12-01 implementation Administration of Quality Supervision, Inspection and Quarantine of People's Republic of China Standardization Administration of China released Table of ContentsIntroduction Ⅲ Introduction Ⅳ 1 Scope 1 2 Normative references 1 3 Definitions and symbols 1 4 LPG in the standard reference temperature of volume 3 5 Quality 3 6 Energy 5 7 quality and liquid at standard reference conditions in terms of volume between the vapor 7 8 is composed of liquid density calculation 8 9 is composed of data to calculate the amount of heat 9 Appendix A (normative) Calculation constant density 11 Appendix B (Normative Appendix) LNG component standard molar volume 12 Appendix C (Normative Appendix) LNG volume of the mixture reduced correction factor 13 Annex D (normative) single-component high heat 14 Appendix E (normative) molecular weight single component 15 and the compression factor Annex F (normative) Calculation LPG mixture of molar volume and saturation density of Alternate Formula 16 Annex G (normative) formula in the critical temperature of the components, the volume of eccentric factor and features 19 References 20ForewordThis revised standard adopts ISO 6578.1991 "Frozen hydrocarbon fluid static measurement and calculation methods." This standard is based on ISO 6578.1991 re-drafted. This standard and ISO 6578.1991 is the main technical difference with Chapter 2 normative references in the national standard replaces ISO standard. This standard and ISO 6578.1991 main editorial differences are as follows. --- "This International Standard" be replaced by "this standard"; --- Delete ISO 6578.1991 foreword, preface rewritten this standard; --- Modify the ISO 6578.1991 Introduction; --- Chapter 5 to Chapter 9, according to GB/T 1.1-2000 requirements of formula uniform numbers; --- Delete ISO 6578.1991 Annex F; --- Increase the "References", according to GB/T 1.1 requirements of the ISO 6578.1991 Appendix reference exchange rate and uniform number. This standard Appendices A to G are normative appendices. This standard by the National Standardization Technical Committee on Gas (SAC/TC244) proposed. This standard by the National Standardization Technical Committee on Gas (SAC/TC244) centralized. This standard is drafted by. China Southwest Oil & Gas Field Branch, Research Institute of Petroleum, China Petroleum West-East Gas Pipeline Company in Nanjing Measurement and Testing Centre. Participated in the drafting of this Standard. China Southwest Oil and Gas Field Branch of oil measuring and testing center, China Petroleum Engineering Co., Ltd. Southwest Company, China CNOOC Gas & Power Co., Ltd., China Petroleum Dalian LNG project department. The main drafters. Zhang Yuan, Wang Jinsong, Luo Qin, Ming Chang country, XIA Fang, Su Yunguo, Zheng Jun, Qiu Hui, wooden bell, Chen Hui Yu, Zhao Jing.IntroductionCurrently, a large Refrigerated light hydrocarbon fluids (such as LNG and LPG) storage and transportation are very common. Because these products in the cold condition, So existing standard measurement of petroleum products do not apply, and in some cases can not even be used. These items should be provided in accordance with this standard Program to replace or modify the existing criteria. Accurate measurement of sales Refrigerated light hydrocarbon fluids, procurement and processing are the most important. Custody transfer protocol requires static measurement process Order standardized and recommended the transfer of the amount to the quality or energy representation. Currently, the use of other units liquefied petroleum gas (LPG), although the transfer shall bear Recognition, but it is not included in this standard. Although the calculation of the amount of static Refrigerated light hydrocarbon fluids at ambient temperature for computing the amount of petroleum products, the principles are similar, but because Refrigerated light hydrocarbon Low temperature and physical properties lead to some differences. These differences are as follows. a) liquid products at or near its bubble point temperature. Refrigerated light hydrocarbon fluids storage tanks will always produce very little heat through the insulating layer Pass, which led to continuous product evaporation. Volatile component in the vapor phase concentration is higher than the concentration in the liquid phase. In order to avoid over Pressure steam is discharged from the tank, and then compressed, cooled and re-liquefaction and reinjection into the tank. b) When the liquid product from a tank into another tank, generate additional heat to the pipeline and pump, causing the Produce more evaporation receiving tank. c) for from a supply tank to the receiving tank custody transfer, typically a vapor return line and the tank connection, in order to avoid vapor feed Into the atmosphere. Re-liquefaction system to avoid the connection pressure. D) After partially filled, the tank liquid component may appear stratified by different temperatures and densities. Therefore, you may need to set up a plurality of temperature Measuring point and a special sampling system. If the filling operation to ensure thorough mixing, you can reduce these settings. e) I have a lot of evidence that there is a big temperature gradient Refrigerated light hydrocarbon vapor space of the tank; and the latter is not linear. If liquid Reading level measurement devices affect different level sensor by pulling cable contraction, it must be suitably compensated (physical Or by calculation). f) Refrigerated light hydrocarbon fluid volume expansion of large temperature coefficient, with a value as follows. --- Propane, 0.20%/℃ --- Methane, 0.35%/℃ It must be emphasized that the temperature measurement error is the main part of the magnitude of the measurement error, and therefore should pay more attention to the choice of the temperature measuring device And use. This standard applies to the measurement of land and ship frozen liquid tank is completely frozen at its vapor pressure near atmospheric pressure when. Do not push Recommended for small package frozen liquid, which can be directly weighed. Calculation does not include the light hydrocarbon liquid or frozen ethane and ethylene pressure mainly by the composition of the light hydrocarbon liquid is higher than the partial freezing atmospheres. Upon obtaining more reliable data, it will be provided in future versions. Measurement procedures mandate holders must have a wealth of experience and skills. Frozen hydrocarbon fluids Static measurement calculation method1 Scope1.1 standard specifies the volume of frozen light hydrocarbon fluids such as LNG (liquefied natural gas) and LPG (liquefied petroleum gas), the measurement conditions In terms of standard reference volume ratio of liquid or vapor temperature and pressure conditions equivalent, or the equivalent in terms of mass or energy (heat) calculation Party law. This standard applies to static storage conditions gauge measuring Refrigerated light hydrocarbon liquid stored in the tank, or transferred from the storage tank, or transfer When entering the tank gauging. 1.2 application of these procedures, the final value is expressed as follows. a) quality (see Note); b) energy (heat); c) an equivalent volume of vapor in standard conditions. Note. The current measurements in practice is to observe the quality of LPG in air. Table 1 gives the conversion factor can be converted into mass observed in air quality. Table 1 conversion factor of quality and air quality observation Density (15 ℃)/(kg/m3) Conversion factor 500.0 - 519.1 519.2 - 542.1 542.2 - 567.3 567.4 - 595.0 595.1 - 625.5 625.6 - 659.3 0.99775 0.99785 0.99795 0.99805 0.99815 0.99825 1.3 If you need a standard reference temperature of the liquid volume indicated in Chapter 4 shows the magnitude and correlation calculation program. Oil production Standard reference temperature of 15 ℃ (see ISO 5024), but is also used in other areas other than a standard reference temperature, such as 20 ℃. If the value calculation involves product density or heat, or can be directly measured by the product composition analysis data calculated 1.4. Article 8 and Chapter 9 gives these programs supporting calculations. 1.5 Appendix A to F shows the normative basis of data and information used in the calculation procedure.2 Normative referencesThe following documents contain provisions which, through the standard reference and become the standard terms. For dated references, subsequently Some amendments (not including errata content) or revisions do not apply to this standard, however, encourage the parties to the agreement are based on research Study whether the latest versions of these documents. For undated reference documents, the latest versions apply to this standard. GB/T 1885-1998 Petroleum Measurement Tables (eqv ISO 91-2.1991) GB/T 11062-1998 natural gas calorific value, density, relative density and Wobbe index calculation method (neqISO 6976.1995)3 Definitions and symbols3.1 Terms and Definitions The following terms and definitions apply to this standard. ......Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of GB/T 24962-2010_English be delivered?Answer: Upon your order, we will start to translate GB/T 24962-2010_English as soon as possible, and keep you informed of the progress. The lead time is typically 3 ~ 5 working days. The lengthier the document the longer the lead time.Question 2: Can I share the purchased PDF of GB/T 24962-2010_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 24962-2010_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay. |
