GB/T 22512.1-2012 English PDFUS$1569.00 · In stock
Delivery: <= 10 days. True-PDF full-copy in English will be manually translated and delivered via email. GB/T 22512.1-2012: Petroleum and natural gas industries -- Rotary drilling equipment -- Part 1: Rotary drill stem elements Status: Valid
Basic dataStandard ID: GB/T 22512.1-2012 (GB/T22512.1-2012)Description (Translated English): Petroleum and natural gas industries -- Rotary drilling equipment -- Part 1: Rotary drill stem elements Sector / Industry: National Standard (Recommended) Classification of Chinese Standard: E92 Classification of International Standard: 75.180.10 Word Count Estimation: 71,775 Quoted Standard: GB/T 228.1; GB/T 229; GB/T 231.1; GB/T 5777; GB/T 9445; GB/T 15822.1; GB/T 18851.1; GB/T 20972.1; GB/T 20972.2; GB/T 20972.3; GB/T 22512.2; ISO 13665; API RP 7G; API SPEC 5DP; ASTM A262; ASTM A434; ASTM E587 Adopted Standard: ISO 10424-1-2004, MOD Regulation (derived from): Announcement of Newly Approved National Standards No. 1 of 2012 Issuing agency(ies): General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China, Standardization Administration of the People's Republic of China Summary: This standard specifies the requirements for the following drill stem elements: upper and lower kelly cock, square and hexagonal kellys, drill stem subs, standard steel drill collars and non-magnetic drill collars, drilling bits and coring drill, HWDP (HW GB/T 22512.1-2012: Petroleum and natural gas industries -- Rotary drilling equipment -- Part 1: Rotary drill stem elements---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order. Petroleum and natural gas industries.Rotary drilling equipment.Part 1. Rotary drill stem elements ICS 75.180.10 E92 National Standards of People's Republic of China Oil and gas industry rotary drilling equipment Part 1. Rotary drill string members Part 1. Rotarydrilstemelements (ISO 10424-1..2004, MOD) 2012-03-09 release 2012-07-01 Implementation General Administration of Quality Supervision, Inspection and Quarantine of the People 's Republic of China China National Standardization Management Committee released Directory Preface III 1 Scope 1 2 Consistency 1 2.1 Unit of measurement 1 2.2 Table with Figure 1 3 normative reference documents 3 4 Terms and Definitions, Symbols and Abbreviations 4 4.1 Terms and definitions 4 4.2 Symbols and Abbreviations 8 5 upper and lower side drill pipe plug valve 9 5.1 General 9 5.2 Design guidelines 9 5.3 Rotary shoulder connection 11 5.4 hydrostatic test 12 5.5 Save files and records 13 5.6 mark 13 5.7 Supplementary requirements 13 6 square drill pipe and hexagonal drill pipe6.1 Specifications, type and size 14 6.2 Dimensional measurement 14 6.3 Rotary shoulder connection 14 6.4 four forging side drill pipe 15 6.5 Mechanical properties 15 6.6 NDT 16 6.7 logo 167 drill string adapterTypes and Types 7.2 Type A and Type B 21 7.3 Type C (faucet adapter) Dimensions 22 7.4 D type (lifting short section) size 22 7.5 Mechanical properties 23 7.6 Non - destructive testing 7.7 Stress-dispersed structure of rotary shoulder connection 7.8 Cold processing of thread roots 24 7.9 Anti-wear treatment of threads and sealed shoulders 7.10 mark 24 8 drill collar 28 8.1 General 28 8.2 Standard steel drill collar 30 8.3 non-magnetic drill collar 32 Drilling bit and core drill bit 9.1 cone bit and scraper bit 38 9.2 Diamond bit, diamond core drill and polycrystalline diamond composite (PDC) drill bit 38 10 Increased drill pipe (HWDP) 42 10.1 General 42 10.2 Mechanical properties 45 10.3 Assembling 47 10.4 Retrospective 47 10.5 logo 47 Non - destructive testing of bars and tubing 11.1 General 47 11.2 Qualification and identification of non-destructive testing personnel 47 11.3 Surface defects 48 11.4 Internal defects 49 Appendix A (informative appendix) Table 51 presented in the US Formula Reference 65ForewordGB/T 22512 "Oil and gas industry rotary drilling equipment" is divided into the following two parts. - Part 1. Rotary drill string members; Part 2. Machining and measurement of rotary shoulder thread connections. This part is part 1 of GB/T 22512. This part is drafted in accordance with the rules given in GB/T 1.1-2009. This part uses the re-drafting method to modify ISO 10424-1..2004 "Oil and gas industry rotary drilling equipment Part 1. Rotating drill string member ". The technical differences between this part and ISO 10424-1..2004 are as follows. --- on the normative reference documents, this part has made a technical differences in the adjustment to meet China's technical conditions, adjust the situation The situation is reflected in Chapter 3, "Normative references", as follows. • GB 682 (see 6.5.2, 8.2.1.1, 8.3.2.1, 10.2.1.1); • GB/T 229 instead of ISO 148 (see 5.2.3.1, 6.5.3.1, 7.5.3.1, 8.2.1.3.1, 10.2.1.3.1); • Replace ISO 6506-1 with GB/T 231.1 with international standard (see 6.5.2, 7.5.2, 8.2.1.2, 8.3.2.2, 10.2.1.2); Replace GB 9303 (see 11.3.3, 11.4.2.1) with GB/T 5777 with international standard modifications; Replace ISO 9712 (see 11.2) with GB/T 9445 equivalent to international standards; Replace ISO 9934-1 (see 5.3.2.2, 11.3.4) with GB/T 15822.1 equivalent to the international standard; Replace GB 3452 (see 5.3.2.3, 11.3.5) with GB/T 18851.1 equivalent to the international standard; ● Replace GB 15156 (all parts) with GB/T 20972 (all parts), the consistency between the two standard parts Degrees are as follows. GB/T 20972.1 Petroleum and natural gas industries Materials for hydrogen sulfide containing oil and gas exploration Part 1. General principles for the selection of anti - crack materials (GB/T 20972.1-2007, ISO 15156-1..2001, IDT); GB/T 20972.2 Petroleum and natural gas industries for oil and gas extraction for hydrogen sulfide-containing materials - Part 2. Anti - cracking carbon steel, low alloy steel and cast iron (GB/T 20972.2-2008, ISO 15156-2..2003, MOD); GB/T 20972.3 Petroleum and natural gas industries Materials for hydrogen sulfide-containing environments for oil and gas extraction Part 3. Anti-cracking corrosion resistant alloys and other alloys (GB/T 20972.3-2008, ISO 15156-3..2003, MOD). • Added reference to GB/T 22512.2 (see 6.3, 7.2.1, 7.3.1, 7.4.2, 7.7, 8.1.7.1.1, 8.1.7.1.2, 8.1.7.2, 8.1.7.3, 10.1.7.1, 10.1.7.2, 10.1.7.3); ● Added reference to APISpec5DP (see Note 2, 7.2.2.1.1 in Figure 1); ● The reference file APISpec7 was deleted. - increased the requirement for low torque structures when machining 75/8REG on drill collar with outside diameter greater than 241.3 mm (91/2 in) 8.1.7.4); - increased the contents of the increased drill pipe (HWDP) (see Chapter 10); - change the qualification of non-destructive testing personnel to "Level 1, Level 2 or 3" (see 11.2); Replace "ISO 10424-1" with the mark "GB/T 22512.1" (see 5.6, 6.7, 7.10, 8.2.2, 8.3.5, 9.1.4, 9.2.4). This section makes the following editorial changes. - the relevant statements in Chapter 2 of the International Standard are deleted; --- Removed the international standard cover, PDF statement, preface and introduction. In addition, some of the errors in ISO 10424-1..2004 are corrected as follows. --- removed the 5.3.1 "anti-wear treatment on the non-magnetic drill collar has no obvious effect, and therefore does not require." Statement; - Table 6 and Table 6, column 6, the value "133.3" is replaced by "133.4"; - 7.3.1 stipulates that "the upper and lower ends of the faucet adapter should be left-handed male thread connection", and in Figure 5 the type C conversion The lower end of the joint is indicated by "4", that is, "rotary shoulder type internal thread or male thread connection", should be changed to "5", that is, "left external thread Then "; --- "7.5" in the "should meet the requirements of 7.2 in the drill collar of the tensile requirements" in the "7.2" to "8.2"; - "The sample should be taken from the thickened end" in 7.5.3.2, where the "thelowerupset" should be removed. Please note that some of the contents of this document may involve patents. The issuer of this document does not assume responsibility for the identification of these patents. This section is under the jurisdiction of the National Petroleum Drilling Equipment and Tools Standardization Technical Committee (SAC/TC96). This part is responsible for drafting units. Beijing Petroleum Machinery Factory. This part participates in the drafting unit. the oil industry well control equipment quality supervision and inspection center, China National Petroleum Corporation pipe research , Baoji Petroleum Machinery Co., Ltd. The main drafters of this part. Wang Ruixiao, Fan Yuzhao, Jiang Yu Gracilaria, Yang Yugang, Yang Lengeng, Xu Ting, Yang Xiaoyong. Oil and gas industry rotary drilling equipment Part 1. Rotary drill string members1 ScopeThis part of GB/T 22512 specifies the requirements for the following drill string components. upper and lower side drill pipe plug valves, square drill pipe and hexagonal drill Rod, drill string adapter, standard steel drill collar and non-magnetic drill collar, drill bit and core drill bit, increased drill pipe (HWDP). This part does not apply to drill pipe and drill pipe joints, rotary shoulder connection design, thread measurement method or original gauge, proof gauge and work For gauges. The typical drill string assembly for this section is shown in Figure 1.2 consistency2.1 units of measurement In this section, the data are expressed in International System of Units (SI) and US Common System (USC). For a particular order, only mining With a unit system, without giving the data expressed in another unit system. Products manufactured in accordance with any of the two units of the unit system are considered to be equivalent and fully interchangeable. Thus, in this part, the requirements expressed in a unit system are consistent with those expressed in another unit system. The data in this part of the text is represented by SI, followed by parentheses in USC. 2.2 tables and graphs Respectively, given the SI and USC two units that the data table. The tables in the text are expressed in SI units and are listed in Appendix A. Out of the form expressed in USC units. For a particular order, only one unit representation should be used. The chart is contained in the text of the chapter on the specific product and is represented by SI and USC units. ......Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of GB/T 22512.1-2012_English be delivered?Answer: Upon your order, we will start to translate GB/T 22512.1-2012_English as soon as possible, and keep you informed of the progress. The lead time is typically 6 ~ 10 working days. The lengthier the document the longer the lead time.Question 2: Can I share the purchased PDF of GB/T 22512.1-2012_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 22512.1-2012_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay. |
