GB/T 22040-2025 English PDFUS$279.00 · In stock
Delivery: <= 3 days. True-PDF full-copy in English will be manually translated and delivered via email. GB/T 22040-2025: Technical requirements and test of weathering quality for plastics of highway furnatures Status: Valid GB/T 22040: Historical versions
Basic dataStandard ID: GB/T 22040-2025 (GB/T22040-2025)Description (Translated English): Technical requirements and test of weathering quality for plastics of highway furnatures Sector / Industry: National Standard (Recommended) Classification of Chinese Standard: P66 Classification of International Standard: 93.080.30 Word Count Estimation: 14,157 Date of Issue: 2025-08-01 Date of Implementation: 2026-02-01 Older Standard (superseded by this standard): GB/T 22040-2008 Issuing agency(ies): State Administration for Market Regulation, Standardization Administration of China GB/T 22040-2025: Technical requirements and test of weathering quality for plastics of highway furnatures---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT22040-2025 ICS 93.080.30 CCSP66 National Standard of the People's Republic of China Replaces GB/T 22040-2008 Plastic products for facilities along highways Weather resistance requirements and test methods Implementation on February 1, 2026 State Administration for Market Regulation The National Standardization Administration issued Table of ContentsPreface III 1 Scope 1 2 Normative references 1 3 Terms and Definitions 1 4 Product Categories 1 5 Technical Requirements 2 6 Test Method 3 7 Inspection Rules 6 Preface This document is in accordance with the provisions of GB/T 1.1-2020 "Guidelines for standardization work Part 1.Structure and drafting rules for standardization documents" Drafting. This document replaces GB/T 22040-2008 "Weather resistance requirements and test methods for plastic products used in highway facilities" and GB/T 22040- Compared with.2008, in addition to structural adjustments and editorial changes, the main technical changes are as follows. a) The terms “artificial climate (xenon arc lamp) test”, “ultraviolet-condensation test”, “ultraviolet region”, “fluorescent ultraviolet lamp” and “irradiance” have been deleted and definitions (see 3.1 to 3.5 of the.2008 edition); b) The technical requirements have been changed to include requirements for plastic products and external organic anti-corrosion coatings (see Chapter 5,.2008). Chapter 5 of the.2011 edition); c) The expression of performance retention rate has been changed (see Table 1, Table 2, Table 2 of the.2008 edition); d) The technical requirements for the resistance of plastic products to artificial accelerated aging by xenon arc lamps have been changed (see Table 1, Table 2 of the.2008 edition); e) Modified the technical requirements for the high temperature and humidity resistance and xenon arc lamp artificial accelerated aging performance of the external organic anti-corrosion coating (see Table 2, Table 2 of the.2008 edition); f) The requirements for aging performance rating of external organic anti-corrosion coatings have been changed (see Table 3, Table 1 of the.2008 edition); g) The requirements for thermal oxygen aging resistance and sulfur dioxide corrosion resistance have been deleted (see Table 2 of the.2008 edition); h) Added the requirements for protection of the cutting area when preparing the specimen (see 6.1.1.1); i) Changed the requirements for state adjustment (see 6.1.2, 6.1.2 of the.2008 edition); j) Added the test method for appearance quality after testing (see 6.1.3); k) Changes have been made to the temperature alternating resistance, high temperature and humidity resistance, cyclic salt spray corrosion resistance, wind and sand erosion resistance, and fluorescent UV resistance. Test methods for artificial accelerated aging performance of xenon arc lamps, artificial accelerated aging performance of xenon arc lamps and resistance to natural exposure (see 6.2~ 6.8, 6.2, 6.3, 6.5, and 6.7 to 6.10 of the.2008 edition); l) The test methods for resistance to thermal oxygen aging and resistance to sulfur dioxide have been deleted (see 6.4 and 6.6 of the.2008 edition); m) The requirements for assessment items have been changed (see 6.9.2, 6.11.2 of the.2008 edition); n) The contents of the inspection rules items have been changed (see Table 6, Table 4 of the.2008 edition); o) The test report requirement has been deleted (see Chapter 8 of the.2008 edition). Please note that some of the contents of this document may involve patents. The issuing organization of this document does not assume the responsibility for identifying patents. This document was proposed and coordinated by the National Technical Committee for Standardization of Transportation Engineering Facilities (Highway) (SAC/TC223). This document was drafted by. Zhonglu Hi-Tech Traffic Inspection and Certification Co., Ltd. and the Highway Science Research Institute of the Ministry of Transport. The main drafters of this document are. Zhang Zhiyong, Liu Yanfei, Ma Xuefeng, Zou Junjun, Li Wei, Zhou Haifeng, Bai Yuanyuan, Han Yue, Guo Donghua, and Liu Yang. This document was first published in.2008 and this is the first revision. Plastic products for facilities along highways Weather resistance requirements and test methods1 ScopeThis document specifies the product classification, technical requirements, test methods and inspection rules for outdoor plastic products for highway facilities. This document applies to the production and inspection of outdoor plastic products for facilities along highways.2 Normative referencesThe contents of the following documents constitute the essential clauses of this document through normative references in this document. For referenced documents without a date, only the version corresponding to that date applies to this document; for referenced documents without a date, the latest version (including all amendments) applies to This document. GB/T 1040.2 Plastics - Determination of tensile properties - Part 2.Test conditions for moulded and extruded plastics GB/T 1040.3 Plastics - Determination of tensile properties - Part 3.Test conditions for films and sheets GB/T 1449 Test method for flexural properties of fiber reinforced plastics GB/T 1766 Rating method for ageing of paints and varnishes GB/T 2411 Plastics and hard rubber - Determination of indentation hardness (Shore hardness) using a durometer GB/T 2423.18 Environmental testing Part 2.Test methods Test Kb. Salt spray, alternating (sodium chloride solution) GB/T 2423.22 Environmental testing Part 2.Test methods Test N. Temperature change GB/T 2423.37 Environmental testing for electric and electronic products Part 2.Test methods Test L. Dust test GB/T 2918 Standard environment for conditioning and testing of plastic specimens GB/T 3681.2 Plastics test methods for exposure to solar radiation Part 2.Direct natural weathering and exposure behind window glass Weathering GB/T 12000 Determination of the effects of exposure of plastics to damp heat, water spray and salt mist GB/T 16422.2 Plastics laboratory light source exposure test method Part 2.Xenon arc lamp GB/T 16422.3 Plastics laboratory light source exposure test method Part 3.Fluorescent ultraviolet lamp3 Terms and DefinitionsThere are no terms or definitions that require definition in this document.4 Product CategoriesAccording to the different product forms, plastic products for facilities along highways are generally divided into the following two categories. --- Plastic products (Class I products) mainly refer to plastic products with synthetic resin as the main body and glass fiber reinforced plastic products. Such as. pipelines, pipe boxes, anti-glare panels, toll booths, sign bases, communication manhole covers, etc. ---External coating organic anti-corrosion coating (Class II products) mainly refers to the use of synthetic resin as the base material and other fillers as auxiliary materials, through extrusion, Products coated on components by electrostatic spraying, fluidized bed dipping or plastic paste, such as external plastic coating of protective facilities and isolation facilities Layer, external plastic coating of electromechanical facilities, etc. ......Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of GB/T 22040-2025_English be delivered?Answer: Upon your order, we will start to translate GB/T 22040-2025_English as soon as possible, and keep you informed of the progress. The lead time is typically 1 ~ 3 working days. The lengthier the document the longer the lead time.Question 2: Can I share the purchased PDF of GB/T 22040-2025_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 22040-2025_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay.Question 5: Should I purchase the latest version GB/T 22040-2025?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 22040-2025 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically. |
