GB/T 2007.7-1987 PDF EnglishUS$90.00 · In stock · Download in 9 seconds
GB/T 2007.7-1987: General rules for the sampling and sample preparation of minerals in bulk. The method for determination of size by manual sieving Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure
Similar standardsGB/T 2007.7-1987: General rules for the sampling and sample preparation of minerals in bulk. The method for determination of size by manual sieving---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT2007.7-1987 GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA UDC 622-3.543.05 GB/T 2007.7-87 Replacing GB 2007-1980 General Rules for the Sampling and Sample Preparation of Minerals in Bulk - The Method for Determination of Size by Manual Sieving APPROVED ON. DECEMBER 15, 1987 Implemented on. OCTOBER 01, 1988 Approved by. National Bureau of Standards Table of Contents1 Applicable Scope... 3 2 Normative References... 3 3 Terms and Definitions... 3 4 Instrument... 4 5 Sieving Methods... 4 6 Calculation of Results... 5 7 Others... 6 Additional Information... 7 General Rules for the Sampling and Sample Preparation of Minerals in Bulk - The Method for Determination of Size by Manual Sieving1 Applicable ScopeThis Standard is applicable to the determination of the grain-sizes of various minerals specified in GB 2007.1.2 Normative ReferencesGB 2007.1 General Rules for the Sampling and Sample Preparation of Minerals in Bulk-Sampling by Manual Method GB 2007.2 General Rules for the Sampling and Sample Preparation of Minerals in Bulk-Manual Method of Sample Preparation GB 2007.5 General Rules for the Sampling and Sample Preparation of Minerals in Bulk-Experimental Method for Checking the Bias of Sampling GB 6003 Test Sieve GB 6004 Square Mesh Woven by Metal Wire for Test Sieve3 Terms and Definitions3.1 Grain-size. it is expressed by the minimum mesh size that the substances pass through the sieve in the sieving test. 3.2 Grain-size distribution. the sample is divided into the particle groups according to the gran-size, which is expressed by the mass percentage. 3.6 Quantity of sample for sieving. the mass of minerals that is actually used in the sieving test. All samples that are taken from a batch of minerals according to GB 2007.1.4 Instrument4.1 Sieve 4.1.1 Shape of mesh. square mesh. 4.1.4 Preparation and verification of sieves. The sieves shall be carefully inspected and cleaned before use. Both new sieves and sieves that have been used for a certain period of time need to check the size of the meshes to ensure that the size of the mesh is within the specified tolerance. For the check method, see GB 6003. 4.2 Weighing apparatus The maximum weighing of the weighing apparatus is required to be close to the quantity of sample used for sieving. If the conditions are not satisfied, it is allowed to weigh for several times. 4.3 Drying oven It has the function of automatically controlling temperature.5 Sieving Methods5.1 Sample-loading quantity. according to the size of the mesh, the area of the screen and the maximum grain-size of the sample, and maximum sample-loading quantity can refer to Table 1. 5.2 Put the sample for sieving with less than the maximum sample-loading quantity listed in Table 1 in the sieve of the specified aperture. Use multiple sieves of different apertures for simultaneous screening; arrange in sequence from top to bottom according to the sizes of the meshes. 5.6 After sieving, each grain-sized sample is measured separately. 5.7 When sieving particles larger than 50mm, the residual minerals on the sieve may be tested by hand. Large-particle minerals may be measured with a square gauge of corresponding size.6 Calculation of Results6.1 When determining the particle size of a large sample, calculate it according to Formula (1), and the result shall retain one digit after the decimal point. 6.2 Determine the grain-size of duplicate sample; calculate according to Formula (2). Each grain-size interval shall be calculated to the two digits after the decimal point.7 Others7.1 If the sample is too wet, it may be dried to a level suitable for sieving at a temperature lower than that causes the changes in sample quality and grain-size. When sieving, if the sample humidity and air humidity are in a balanced state, more satisfactory results can be obtained. 7.3 In order to protect the screen, the maximum grain-size of the sample shall be limited for sieves with different apertures, as shown in Table 2. ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 2007.7-1987 be delivered?Answer: The full copy PDF of English version of GB/T 2007.7-1987 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 2007.7-1987_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 2007.7-1987_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 2007.7-1987 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.How to buy and download a true PDF of English version of GB/T 2007.7-1987?A step-by-step guide to download PDF of GB/T 2007.7-1987_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 2007.7-1987". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
