GB/T 18443.4-2010 PDF EnglishUS$70.00 · In stock · Download in 9 seconds
GB/T 18443.4-2010: Testing method of performance for vacuum insulation cryogenic equipment - Part 4: Leak-outgassing rate measurement Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid GB/T 18443.4: Historical versions
Similar standardsGB/T 18443.4-2010: Testing method of performance for vacuum insulation cryogenic equipment - Part 4: Leak-outgassing rate measurement---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT18443.4-2010 NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 23.020 J 74 Replace GB/T 18443.4-2001 Testing method of performance for vacuum insulation cryogenic equipment - Part 4.Leak-outgassing rate measurement Issued on. SEPTEMBER 26, 2010 Implemented on. FEBRUARY 1, 2011 Issued by. General Administration of Quality Supervision, Inspection and Quarantine of PRC; Standardization Administration of PRC. Table of ContentsForeword... 3 1 Scope... 5 2 Normative references... 5 3 Terms and definitions... 5 4 Test principle and method... 6 5 Test devices, equipment, and instruments... 7 6 Test conditions and test preparation... 7 7 Test steps... 8 8 Data processing... 9 9 Test records and test reports... 11 Appendix A (Informative) Leak-outgassing rate test record (direct method)... 12 Appendix B (Informative) Leak-outgassing rate test report... 15ForewordGB/T 18443 “Testing method of performance for vacuum insulation cryogenic equipment” is divided into 8 parts. --- Part 1.Basic requirements; --- Part 2.Vacuum degree measurement; --- Part 3.Leak rate measurement; --- Part 4.Leak-outgassing rate measurement; --- Part 5.Static evaporation rate measurement; --- Part 6.Heat-leak rate measurement; --- Part 7.Holding time measurement; --- Part 8.Volume measurement. This part is Part 4 of GB/T 18443. This part replaces GB/T 18443.4-2001 “Testing method of cryo-insulation pressure vessels - Leak and outgassing rate measurement”. Compared with GB/T 18443.4-2001, the main changes of this part are as follows. --- The scope of application has been expanded from the leak-outgassing rate measurement of cryogenic insulation pressure vessels to the leak-outgassing rate measurement of vacuum insulated cryogenic pressure vessels, vacuum insulated cryogenic welded gas cylinders, vacuum insulated pipes and pipe fittings, and other vacuum insulated cryogenic equipment; --- Some terms and definitions are added and modified; --- The requirements for the duration of the test are added; --- The indirect measurement method 2 is added; --- The formats of test records and test reports are added. Appendix A and Appendix B of this part are informative appendices. This document was proposed by and shall be under the jurisdiction of China Standardization Committee on Boilers and Pressure Vessels (SAC/TC262). Drafting organizations of this document. Shanghai Institute of Special Equipment Inspection and Technical Research, Shanghai Gas Industry Association, Aerosun Corporation, Shanghai Jiao Tong University, National Cryogenic Vessel Quality Supervision and Inspection Center, Shanghai Huayi Engineering Co., Ltd., China Special Equipment Inspection and Research Institute. The main drafters of this document. Wang Fang, Zhou Weiming, Luo Xiaoming, Wang Rongshun, Shu Wenhua, Shou Binan, Xue Jiai, Chen Guangqi, Gu Fuming, Shi Fengping, Wei Yongbiao, Xue Xiaolong, Wang Weiguo. The previous versions of the standards replaced by this part are as follows. --- GB/T 18443.4-2001. Testing method of performance for vacuum insulation cryogenic equipment - Part 4.Leak-outgassing rate measurement1 ScopeThis part of GB/T 18443 specifies the requirements of the test principle and method, test devices, equipment and instruments, test conditions and test preparations, test procedures, data processing, test records, and test reports for the measurement of interspace leak-outgassing rate of vacuum insulated cryogenic equipment. This part applies to the measurement of interspace leak-outgassing rate of vacuum insulated cryogenic equipment, such as vacuum insulated cryogenic pressure vessels except for the storage and transportation of liquid hydrogen medium, vacuum insulated cryogenic welded gas cylinders, vacuum insulated pipes and pipe fittings; the measurement of other equipment can be implemented by reference.2 Normative referencesThe provisions in the following documents become the provisions of this Part through reference in this Part of GB/T 18443.For the dated references, the subsequent amendments (excluding corrections) or revisions do not apply to this Part, however, parties who reach an agreement based on this Part are encouraged to study if the latest versions of these documents are applicable. For undated references, the latest edition of the referenced document applies to this Part. GB/T 18443.1-2010 Testing method of performance for vacuum insulation cryogenic equipment - Part 1.Basic requirements GB/T 18443.2 Testing method of performance for vacuum insulation cryogenic equipment - Part 2.Vacuum degree measurement3 Terms and definitionsThe terms and definitions established in GB/T 18443.1-2010, GB/T 18443.2, GB/T 18443.3 and the following apply to this part. 3.1 Desorption The release of gas or vapor adsorbed by a material. The release can be natural or accelerated by physical means. 3.2 Outgassing Natural desorption of gas from a material.4 Test principle and method4.1 Calculate the value of the leak-outgassing rate by measuring the change value of the static interspace vacuum degree within a certain time interval at room temperature. 4.2 The leak-outgassing rate measurement of vacuum interspace is divided into the direct measurement method and the indirect measurement method.5 Test devices, equipment, and instrumentsTest devices, equipment, and instruments shall comply with the provisions of 4.2 in GB/T 18443.1.6 Test conditions and test preparationTest conditions and test preparations shall comply with the provisions of GB/T 18443.1. When the indirect measurement method is used, the following requirements shall also be met.7 Test steps7.1 Direct measurement method 7.2 Indirect measurement method 7.2.1 Indirect measurement method 1 7.2.1.1 Close the vacuum valve of the measured piece and the vacuum valve of the pumping system, record the background vacuum degree of the measuring pipeline, then open the vacuum valve of the measured piece, and observe the change of the vacuum degree of the measuring pipeline. After the pressure is balanced, record the stable initial vacuum degree of the connected space and the time. 7.2.2 Indirect measurement method 2 7.2.2.1 Close the vacuum valve of the measured piece and the vacuum valve of the pumping system, record the background vacuum degree of the measuring pipeline, then open the vacuum valve of the measured piece, and observe the change of the vacuum degree of the measuring pipeline. 7.2.2.2 The duration of the test shall be not less than 2 h and not more than 72 h; close the vacuum valve of the pumping system, record the background vacuum degree P0 of the pipeline, open the vacuum valve of the measured piece, and observe the change of the vacuum degree of the measuring pipeline.8 Data processing8.1 When using the direct measurement method to measure the leak-outgassing rate, calculate it according to formula (1). 8.2 When using the indirect measurement method 1 to measure the leak-outgassing rate, calculate it according to formula (2). 8.3 When using the indirect measurement method 2 to measure the leak-outgassing rate, calculate it according to the following formulas.9 Test records and test reports9.1 Please refer to Appendix A for the formats of the test records.Appendix A(Informative) Leak-outgassing rate test record (direct method) Refer to Table A.1 for the test record form of the leak-outgassing rate measured with the direct method. ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 18443.4-2010 be delivered?Answer: The full copy PDF of English version of GB/T 18443.4-2010 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 18443.4-2010_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 18443.4-2010_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 18443.4-2010 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.Question 5: Should I purchase the latest version GB/T 18443.4-2010?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 18443.4-2010 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically.How to buy and download a true PDF of English version of GB/T 18443.4-2010?A step-by-step guide to download PDF of GB/T 18443.4-2010_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 18443.4-2010". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
