GB/T 18029.19-2014 English PDFUS$834.00 · In stock
Delivery: <= 3 days. True-PDF full-copy in English will be manually translated and delivered via email. GB/T 18029.19-2014: Wheelchairs -- Part 19: Wheeled mobility devices for use as seats in motor vehicles Status: Valid
Basic dataStandard ID: GB/T 18029.19-2014 (GB/T18029.19-2014)Description (Translated English): Wheelchairs -- Part 19: Wheeled mobility devices for use as seats in motor vehicles Sector / Industry: National Standard (Recommended) Classification of Chinese Standard: Y14 Classification of International Standard: 11.180 Word Count Estimation: 42,484 Date of Issue: 12/31/2014 Date of Implementation: 7/1/2015 Quoted Standard: GB/T 18029.15-2008; GB/T 18029.22-2009; GB/T 18029.26-2014; ISO 3795; ISO 6487; ISO 7176-5; ISO 10542-1-2001; ISO 10542-2-2001; FMVSS 209-2004 Adopted Standard: ISO 7176-19-2008, IDT Regulation (derived from): National Standards Bulletin 2014 No. 33 Issuing agency(ies): General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China, Standardization Administration of the People's Republic of China Summary: This Standard specifies the wheelchair design requirements, performance requirements and test methods related to the side, also provides for identification wheelchair, pre-file, instructions and information for report content. These provisions apply to th GB/T 18029.19-2014: Wheelchairs -- Part 19: Wheeled mobility devices for use as seats in motor vehicles---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order. Wheelchairs Part 19. Wheeled mobility devices for use as seats in motor vehicles ICS 11.180 Y14 National Standards of People's Republic of China Wheelchairs - Part 19. Wheeled mobile device can be used for vehicle seats Wheelchairs-Part 19. Wheeledmobilitydevicesforuseas (ISO 7176-19.2008, IDT) Issued on. 2014-12-31 2015-07-01 implementation Administration of Quality Supervision, Inspection and Quarantine of People's Republic of China Standardization Administration of China released Table of ContentsIntroduction Ⅲ Introduction Ⅳ 1 Scope 1 2 Normative references 1 3 Terms and definitions 4 design requirements 6 4.1 wheelchair fixing system 6 4.2 occupant safety limit system 6 5 Performance Requirements 9 5.1 fixed the car seat belt 9 in a wheelchair 5.2 11 head-on collision 5.3 Applicability of four o'clock adapter hook tape fastener 12 points 5.4 Applicability of fixed vehicle seat belt in a vehicle 12 6 identification, labeling, instructions for use, warnings and publicity requirements 12 6.1 Identification and labeling 12 6.2 13 pre-file 6.3 Use and maintenance instructions 13 7 Compliance Document 15 7.1 General requirements 15 7.2 frontal crash test 15 7.3 design, labeling and documentation requirements 15 Appendix A (normative) frontal impact test method 16 Geometrical parameters 23 Annex B (normative) for docking four o'clock belt fastener system wheelchair securing points Ease of testing methods Appendix C (normative) wheelchair securing points and the four-point belt fastener system 25 connected Annex D (normative) wheelchair vehicle seat belt applicability Rating Methodology 28 Appendix E (normative) Alternative tiedown Guide 32 Annex F (normative) Universal Docking Interface Specification geometric description 33 References 37ForewordGB/T 18029 "wheelchair" or has plans to release the following sections. --- Part 1. Determination of static stability; --- Part 2. Determination of dynamic stability of electric wheelchairs; --- Part 3. Determination of the brake; --- Part 4. Determination of electric wheelchairs and electric scooters theory energy consumption; --- Part 5. Dimensions, mass and turning space, measured; Electric wheelchairs maximum speed, acceleration and deceleration measured;. --- Part 6 --- Part 7. Measurement of seating and wheel sizes; --- Part 8. static strength, impact strength and fatigue strength requirements and test methods; --- Part 9. electric wheelchairs climatic test methods; --- Part 10. Determination of electric wheelchair obstacle capacity; --- Part 11. Test dummies; --- Part 13. Determination of the test surface coefficient of friction; --- Part 14. electric wheelchairs and electric scooters and power control system requirements and test methods; --- Part 15. release of information, documents and requirements issued identification; --- Part 16. Block (by) pad flame retardancy requirements and test methods; --- Part 19. Wheeled mobile device can be used for vehicle seats; --- Part 21. electric wheelchair, electric scooter battery charger and electromagnetic compatibility requirements and test methods; --- Part 22. Adjustment Program; --- Part 23. Requirements and test methods for stair climbing device caregiver operations; --- Part 24. Requirements and test methods occupant operated stair climbing apparatus; --- Part 26. Terminology. This section GB/T 18029 Part 19. This section drafted in accordance with GB/T 1.1-2009 given rules. This section uses the translation method identical with ISO 7176-19.2008 "Wheelchairs - Part 19. Wheel can be used for vehicle seats shift Actuating means. " Consistency correspondence between this part of international documents and normative references of our files are as follows. --- GB/T 18029.5-2008 Wheelchairs - Part 5. Dimensions, mass and turning space measurement (ISO 7176-5. 1986, IDT) --- GB/T 20953-2007 Determination of agricultural and forestry tractors and machinery cab interior material combustion characteristics (ISO 3795. 1989, MOD) Please note that some of the content of this document may involve patents. Release mechanism of the present document does not assume responsibility for the identification of these patents. This section proposed by the People's Republic of China Ministry of Civil Affairs. This part of the National Rehabilitation and special equipment Standardization Technical Committee on Persons with Disabilities (SAC/TC148) centralized. This section is drafted. Fujian orthopedic products tested by the National Research Center for Rehabilitation Technical Aids. The main drafters of this section. Chen Guoqing, Ma Feng collar, ROCKETS, Ding Hao, Liu Junling.IntroductionTraffic safety research shows that the vehicle is an important part of the seat occupant safety limit system, in all kinds of traffic accidents to reduce the ride Danger of serious injury who plays a key role. Of particular note is that the vehicle seat belt should occupant bones Regional position, when the impact can not be increased occupant load, and can provide effective support for the occupant to the seat belt in Entire collision course remain in the normal position of the bone area. There are people with physical disabilities, whether the driver or passenger, took the opportunity to move in Usually a wheelchair in the car when the car must travel. Since most wheelchairs are not designed for this purpose, and in the event of a traffic accident, sitting Higher risk in the wheelchair seat occupant sitting in the vehicle than in the original seat occupant hurt. ISO 10542-1 gives the wheelchair and secured safety limit system design, performance, and identify the manufacturer of the relevant documentation requirements, and Provisions of the relevant detection method. For a motor vehicle seat for wheelchair, this part of GB/T 18029 through the establishment of design, performance, logo, And requires manufacturers and related files detection method, part of the wheelchair seat occupant protection systems make a statement. When the relevant part of the standard setting, around the world there are various types of wheelchairs and security systems. In actual use wheelchairs Securing the stability of the system needs effective vehicle wheelchair and security systems combined. Four o'clock belt fastener suitable for most models and Sized wheelchair, is considered the most effective, the most common and widely accepted fixation. For these reasons, this part of the criteria to be Ask for a motor vehicle seat wheelchair using a four-point belt fastener system offers at least four securing points, two in front, two behind. for Wheelchair other fixation methods, such as butt-type fastening system, this part of GB/T 18029 also specifies the test methods. To assess the crashworthiness of the wheelchair, the provisions of Appendix A kinetic test procedures. Load the correct size of the wheelchair positive impact dummy Pulley fixed on collision at a speed of 48km/h crash test performed. This test is based on a number of known vehicle collision and injury statistics Meter data on the basis of these data show that over 50% of serious injury motor vehicle occupant is caused by a frontal impact, the lack of speed 48km/h when more than 95% of the head-on collision caused by a motor vehicle longitudinal deformation. The rear seats forward facing wheelchair, side collision dynamics You will be able to test the standard set forth in the future. GB/T 18029 in this part of the view that when the vehicle frontal collision, only the Department of the pelvic harness occupant can not be obtained simultaneously shoulder And pelvic harness level of protection. Therefore, the relevant provisions of this section and test methods GB/T 18029 requirements and is based while With pelvic belts and shoulder belts. When GB/T 18029 in this part of the preparation, four-point belt fastener system is effectively fixed variety of wheelchairs most common and the most common side Method, but this method requires another person to operate, they can not complete the occupant secured. It is therefore desirable to develop a wheelchair can be made Occupant complete fixation fastener alone, wheelchair occupants may use different public transport or private vehicles. To achieve To this end, this part of GB/T 18029 contains a normative appendix (Appendix F), public transport or private motor For Wheelchair docking fixture used car, Appendix F developed a universal butt joint geometry specifications wheelchair securing points (UDIG). Finally, wheelchair and all everyday use wheelchairs should comply with a series of criteria, general considerations in this part of the standard. First by wheelchair As an effective means to move, therefore, it should comply with the relevant requirements of the standard GB/T 18029 other parts of the regulations. Only traffic travel Only wheelchair and its occupant has a unique use of environmental requirements in their daily lives. In line with GB/T 18029 in this section Products for the wheelchair when the wheelchair occupant in the vehicle by providing a higher level of security. However, no accord This section GB/T 18029 requirements of wheelchair should not limit its use in a motor vehicle transportation. Wheelchairs - Part 19. Wheeled mobile device can be used for vehicle seats1 ScopeThis section GB/T 18029 specifies the wheelchair design requirements, performance requirements and related test methods, also provides for a wheelchair Vehicle identification, pre-sales documents, instructions and warnings and so on. These provisions apply to the whole base frame wheelchairs and seating systems constituted also applies to systems with additional components (designed to meet a Or more of the requirements) of the wheelchair. This section applies to all manual and power wheelchairs, including scooters, which in addition to the basic functions for wheeled mobile, but also often used As the vehicle to the front seat occupant can be equal or greater than 22kg body weight for children or adults.2 Normative referencesThe following documents for the application of this document is essential. For dated references, only the dated version suitable for use herein Member, undated references, the latest edition (including any amendments) applies to this document. GB/T 18029.15-2008 Wheelchairs - Part 15. release of information, documents and requirements issued identification (ISO 7176-15. 1996, IDT) GB/T 18029.22-2009 Wheelchairs - Part 22. Adjusting program (ISO 7176-22.2000, IDT) GB/T 18029.26-2014 Wheelchairs - Part 26. Terminology (ISO 7176-26.2007, IDT) ISO 3795 Determination of agricultural and forestry tractors and machinery cab interior material combustion characteristics (Roadvehicles, tractorsand machineryforagricultureandforestry-Determinationofburningbehaviourofinteriormaterials) ISO 6487 Road motor vehicle crash test test method for measuring instruments (Roadvehicles-Measurementtechniques inimpacttests-Instrumentation) ISO 7176-5 Wheelchairs - Part 5. Dimensions, mass and turning space measurement (Wheelchairs-Part 5. Deter- minationofdimensions, massandmanoeuvringspace) ISO 10542-1.2001 Assistive technology systems wheelchair tiedown and occupant safety beam protection systems - Part 1. System Requirements and test methods (Technicalsystemsandaidsfordisabledorhandicappedpersons-Wheelchair tiedownandoccupant-restraintsystems-Part 1. Requirementsandtestmethodsforalsystems) Solid Part 2 devices and occupant protection systems 2001 security bundle Assistive Technology Systems Department wheelchair.. ISO 10542-2 four points Belt safety limit system (Technicalsystemsandaidsfordisabledorhandicappedpersons-Wheelchair tiedownandoccupant-restraintsystems-Part 2. Four-pointstrap-typetiedownsystems) FMVSS209.2004,209 number standard seat belt installation, the Federal Motor Vehicle Safety Standard (Seatbeltassemblies. FederalMotorVehicleSafetyStandards, 49CFR571.209,1October, 2004) ECE Regulation 16 adult vehicle occupant safety belts and limit unified standard system (Uniformprovisionscon- cerningtheapprovalofsafetybeltsandrestraintsystemsforadultoccupantsofpower-drivenvehicles, Revision3, Amendment2,16August1993)3 Terms and DefinitionsThe following terms and definitions apply to this document. ......Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of GB/T 18029.19-2014_English be delivered?Answer: Upon your order, we will start to translate GB/T 18029.19-2014_English as soon as possible, and keep you informed of the progress. The lead time is typically 1 ~ 3 working days. The lengthier the document the longer the lead time.Question 2: Can I share the purchased PDF of GB/T 18029.19-2014_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 18029.19-2014_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay. |
