GB/T 16611-2017 English PDFUS$859.00 ยท In stock
Delivery: <= 7 days. True-PDF full-copy in English will be manually translated and delivered via email. GB/T 16611-2017: General specification for radio data transmission transceiver Status: Valid GB/T 16611: Historical versions
Basic dataStandard ID: GB/T 16611-2017 (GB/T16611-2017)Description (Translated English): General specification for radio data transmission transceiver Sector / Industry: National Standard (Recommended) Classification of Chinese Standard: M36 Classification of International Standard: 33.060.01 Word Count Estimation: 43,433 Date of Issue: 2017-05-31 Date of Implementation: 2017-12-01 Older Standard (superseded by this standard): GB/T 16611-1996; GB/T 18120-2000 Quoted Standard: GB/T 2828.1-2012; GB/T 2829-2002; GB 4943.1-2011; GB/T 6107-2000; GB/T 12192-1990; GB/T 12193-1990; GB/T 14013-1992; GB/T 15844-2017; GB/T 17626.2-2006 Adopted Standard: IEC 60489-6-1999, NEQ Regulation (derived from): National Standard Notice 2017 No. 13 Issuing agency(ies): General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China, Standardization Administration of the People's Republic of China Summary: This standard specifies the technical requirements, test methods and quality assessment procedures for wireless data transmission transceivers (hereinafter referred to as data transmission machines), as well as the requirements for marking, packaging, transportation and storage. This standard is applicable to all kinds of data transmission machines that meet the following restrictions for use in ground, inland or coastal special data communication networks (such as telemetry, remote control, remote signaling, remote-adjustment systems, etc.): a) Operating frequencies from 25 MHz to 1 000 Between MHz; b) Constant envelope narrowband modulation; c) Carrier power not greater than 50 W; d) Binary serial data interface to data terminal equipment; e) The transmitted data signal is a bit stream or string. Other relevant radio data communication equipment can refer to implementation. GB/T 16611-2017: General specification for radio data transmission transceiver---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order.Generic specification for data transceiver ICS 33.060.01 M36 National Standards of People's Republic of China Replacing GB/T 16611-1996, GB/T 18120-2000 General Specification for Wireless Data Transceivers (IEC 60489-6.1999, Radioequipmentusedinmobileservices- Methodsofmeasurement-Part 6.Dataequipment,NEQ) 2017-05-31 Published by 2017-12-01 implementation General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China China National Standardization Administration released Directory Preface III 1 Scope 1 2 Normative references 1 3 Terms and Definitions 1 4 Category 2 5 Technical requirements 3 6 Test Method 8 7 Quality Assessment Procedure 28 8 Signs, packaging, transport and storage 32 Appendix A (Normative) Unqualified Category 33 Appendix B (normative) Pulse noise tolerance measurement method 34 Appendix C (Normative) Multipath propagation condition sensitivity measurement method 36 Appendix D (Normative) Conducted and Radiated Spurious Component Measurement Method 38 ForewordThis standard was drafted in accordance with the rules given in GB/T 1.1-2009. This standard supersedes GB/T 16611-1996 "General Specification for Radio Stations" and GB/T 18120-2000 "Selection of Calls and Calls for Mobile Communications". Data Equipment Measurement Methods." The main changes from this standard compared with GB/T 16611-1996 are as follows. ---Instead of the term "digital radio", the term "wireless data transmission transceiver"; modified and added some terms and definitions (1996) Chapter 3 of the Year Edition; Chapter 3 of this edition); --- Modified classification (Chapter 4 of the.1996 edition; Chapter 4 of this edition); --- Cancellation of specific regulations on call performance (Chapter 5 of the.1996 edition, relevant contents of Chapters 6 and 7); --- Cancellation of "Feature Frequency Tolerance," "Data Interface Level," and "General Digital Transmission Performance" indicator requirements and methods of measurement (1996 edition) 5.4.2, 5.4.4, 6.4.2.7 and 6.4.4 related content); --- Cancellation of reliability and test method provisions (1996 version 5.8 and 6.8); --- Revised the names and definitions of some indicator items (Chapter 5 and Chapter 6 of the.1996 edition; Chapters 5 and 6 of this edition); --- Revised some indicator requirements (Chapter 5 of the.1996 edition; Chapter 5 of this edition); --- Modify the test method for some indicators (Chapter 6 of the.1996 edition; Chapter 6 of this edition); --- Increased the test method when using a self-contained antenna (see Chapter 6); --- Increased electrostatic discharge test requirements (see 5.5); --- Added "Impulse Noise Tolerance" indicator definition and measurement method (see Appendix B); --- Modify the "Multipath Propagation Conditions Sensitivity" indicator definition and measurement methods (1996 version 6.4.3.2.1; this edition of Appendix C); --- Added definitions and measurement methods for the "Stray and Radiated Spurious Component" indicator (see Appendix D). The main changes from this standard to GB/T 18120-2000 are as follows. --- Deleted a detailed description of the test conditions and measuring equipment (Chapter 4 to Chapter 6 of the.2000 edition, Appendix A to Appendix D); --- Contains and modifies the definition and measurement methods of related indicator items (Chapter 7 of the.2000 edition; Chapters 5 and 6 of this edition). This standard uses the redrafted method to refer to IEC 60489-6.1999 "Measuring methods for wireless equipment in the mobile service Part 6. Data design Prepared to prepare, and the degree of consistency with IEC 60489-6.1999 is not equivalent. Please note that some of the contents of this document may involve patents. The issuing agency of this document does not assume responsibility for identifying these patents. This standard was proposed by the Ministry of Industry and Information Technology of the People's Republic of China. This standard is under the jurisdiction of the Ministry of Industry and Information Technology (Electronics) of the People's Republic of China. This standard is mainly drafted by. China Electronics Technology Group Corporation Seventh Institute, Guangzhou Jiesai Technology Co., Ltd. Participated in the drafting of this standard. Guangdong Radio Monitoring Station, Shenzhen Huaxia Technology Co., Ltd., Zhejiang Lanbo Electronics Co., Ltd., Beijing Deli Hengtong Communication Technology Co., Ltd., Shenzhen Youxida Technology Development Co., Ltd., National Mobile Communication Engineering Center. Drafters of this standard. Chen Jianyuan, Zhu Yanghe, Xie Huiqun, Li Zhiliang, Xiong Xiong, Xie Xing, Wu Haiyan, Cui Hejian, Bian Wenwei, Zhu Xianwei, Cui Tao, Huang Donghui and Teng Huanglong. The previous versions of the standard replaced by this standard are. ---GB/T 16611-1996; --- GB/T 18120-2000. General Specification for Wireless Data Transceivers1 ScopeThis standard specifies the technical requirements, test methods and quality assessment procedures for wireless data transmission transceivers (hereinafter referred to as data transmission machines). And signs, packaging, transportation and storage requirements. This standard applies to all types of symbols used for ground, inland or coastal special data communication networks (such as telemetry, remote control, remote signaling, remote adjustment systems, etc.) Combined with the following data transfer machine. a) The operating frequency is between 25MHz~1000MHz; b) constant envelope narrowband modulation; c) The carrier power is not more than 50W; d) use a binary serial data interface to connect to data terminal equipment; e) The transmitted data signal is a bit stream or a string of characters. Other relevant radio data communication equipment can refer to implementation.2 Normative referencesThe following documents are indispensable for the application of this document. For dated references, only dated versions apply to this article Pieces. For undated references, the latest version (including all amendments) applies to this document. GB/T 2828.1-2012 Count sampling inspection procedures Part 1. Batch inspection sampling based on AQL plan GB/T 2829-2002 Periodic Inspection Count Sampling Procedures and Tables (Applicable to Inspection of Process Stability) GB 4943.1-2011 Information technology equipment safety - Part 1. General requirements GB/T 6107-2000 Interface between data terminal equipment and data circuit termination equipment using serial binary data exchange GB/T 12192-1990 FM radio frequency telephone transmitter measurement method GB/T 12193-1990 FM radio frequency telephone receiver measurement method GB/T 14013-1992 Mobile Communication Equipment Transport Package GB/T 15844-2017 General specifications for FM transceivers for mobile communications GB/T 17626.2-2006 Electromagnetic compatibility test and measurement techniques Electrostatic discharge immunity test ITU-T V-series recommends data communication over the telephone network3 Terms and definitionsThe following terms and definitions apply to this document. 3.1 Wireless data transmission transceiver radiodatatransmissiontransceiver The radio transceivers used for data signal transmission purposes are also commonly referred to as data radio stations, and are referred to as data transmission machines for short. Note. Some types of wireless data transmission transceivers are also sometimes referred to as radio modems, data transmission modules, etc. 3.2 Number compatible with data/speech compatible The data transmission machine has a digital transmission (data transmission) function and a call (voice transmission) function. ......Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of GB/T 16611-2017_English be delivered?Answer: Upon your order, we will start to translate GB/T 16611-2017_English as soon as possible, and keep you informed of the progress. The lead time is typically 4 ~ 7 working days. The lengthier the document the longer the lead time.Question 2: Can I share the purchased PDF of GB/T 16611-2017_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 16611-2017_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay.Question 5: Should I purchase the latest version GB/T 16611-2017?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 16611-2017 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically. |
