GB/T 14986.4-2018 PDF EnglishUS$145.00 · In stock · Download in 9 seconds
GB/T 14986.4-2018: Soft Magnetic Alloys - Part 4: Iron-chromium Alloys Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid
Similar standardsGB/T 14986.4-2018: Soft Magnetic Alloys - Part 4: Iron-chromium Alloys---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT14986.4-2018GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 77.140.40 H 58 Partially replacing GB/T 14986-2008 Soft Magnetic Alloys - Part 4.Iron-chromium Alloys Issued on. JUNE 7, 2018 Implemented on. MARCH 1, 2019 Issued by. State Administration for Market Regulation of the People’s Republic of China; Standardization Administration Committee of the People’s Republic of China. Table of ContentsForeword... 3 1 Scope... 5 2 Normative References... 5 3 Terms and Definitions... 6 4 Content of Order... 6 5 Dimension and Appearance... 7 6 Technical Requirements... 7 7 Test Methods... 9 8 Inspection Rules... 9 9 Packaging, Mark and Quality Certificate... 10 Appendix A (informative appendix)... 11 Appendix B (informative appendix)... 12ForewordGB/T 14986 Soft Magnetic Alloys is divided into five parts as follows. -- Part 1.general requirements; -- Part 2.iron-nickel alloys; -- Part 3.iron-cobalt alloys; -- Part 4.iron-chromium alloys; -- Part 5.iron-aluminum alloy. This is the fourth part of GB/T 14986. This Part is drafted in accordance with stipulations in GB/T 1.1-2009. This Part is drafted as a replacement of iron-chromium alloys part in GB/T 14986-2008 High Saturation Magnetic Induction Magnetic Compensate Alloys Depending on Temperature Variation Corrosion-resisting Iron-aluminum Permanent Permeability Soft Magnetic Alloys. In comparison with GB/T 14986-2008, there are several main technical changes as follows. -- 1J111 alloy and relevant technical requirements are added (refer to Chapter 5 and 6.4); -- The limitation of S element content in 1J116 and 1J117 becomes more rigorous; the upper limit changes from 0.020% to 0.015% (refer to Table 1; Table 10 in Version 2008); -- 1J117 cold-rolled strip and relevant technical requirements are added (refer to Chapter 1 and Table 2; Chapter 1 in Version 2008); -- 1J116 and 1J117 cold-drawn wire and relevant technical requirements are added (refer to Chapter 1 and Table 2; Chapter 1 in Version 2008); -- Smelting methods are modified (refer to 6.2; 6.2 in Version 2008); -- The magnetic performance of 1J116 is enhanced; coercivity decreases from 80 A/m to 70 A/m (refer to Table 3; Table 13 in Version 2008); -- The re-inspection and determination rules of alloy bar low-magnification and tower-shaped texture are added as a supplement (refer to 8.4.2, 8.4.3; Chapter 9 in Version 2008); -- The fundamental physical parameters of alloys are added as a supplement (refer to Appendix B; Appendix B in Version 2008). This Part is proposed by China Iron and Steel Industry Association (CISA). This Part is summarized by National Technical Committee 183 on Steel Standardization (SAC/TC 183). This Part is drafted by. Dalian Precision Alloy Co., Ltd. of DONGBEI Special Steel Group, China Metallurgical Information and Standardization Institute. The main drafters of this Part include. Xu Xiaoping, Luanyan, Daiqiang, Yan Chengming. The issuing of the previous versions of the standard replaced by this Part is listed below. -- GBn 160-1982, GBn 160-1988; -- GB/T 14986-1994, GB/T 14986-2008. Soft Magnetic Alloys - Part 4.Iron-chromium Alloys1 ScopeThis Part in GB/T 14986 specifies the terms, definitions, content of order, dimension, appearance, technical requirements, test methods, inspection rules, packaging, mark and quality certificate of iron-chromium soft magnetic alloys with relatively high saturation, magnetic induction strength, and relatively low coercivity. This Part is applicable to cold-rolled strip, cold-rolled sheet, cold-drawn wire, hot-rolled strip, hot-rolled wire rod and hot-rolled (wrought) bar (hereinafter referred to as alloys) that apply 1J111, 1J116 and 1J117 iron-chromium soft magnetic alloys to certain corrosive medium.2 Normative ReferencesThe following documents are indispensable to the application of this Standard. In terms of references with a specified date, only versions with a specified date are applicable to this Standard. The latest version (including all the modifications) of references without a specified date is also applicable to this Standard. GB/T 223.5 Steel and Iron - Determination of Acid-soluble Silicon and Total Silicon Content - Reduced Molybdosilicate Spectrophotometric Method GB/T 223.11 Iron, Steel and Alloy - Determination of Chromium Content - Visual Titration or Potentiometric Titration Method GB/T 223.13 Methods for Chemical Analysis of Iron, Steel and Alloy - The Ammonium Ferrous Sulfate Titration Method for the Determination of Vanadium Content GB/T 223.18 Methods for Chemical Analysis of Iron, Steel and Alloy - The Sodium Thiosulfate Separation Iodimetric Method for the Determination of Copper Content GB/T 223.20 Methods for Chemical Analysis of Iron, Steel and Alloy - The Potentiometric Titration Method for the Determination of Cobalt Content3 Terms and DefinitionsTerms and definitions provided in GB/T 14986.1-2018 are applicable to this Standard.4 Content of OrderOrder-placing contract shall include the following content.5 Dimension and AppearanceThe dimension, appearance and allowable deviation of alloys shall comply with stipulations in GB/T 14986.1-2018.The thickness of cold-rolled strip and the allowable deviation division of trimming width shall be indicated in the contract.6 Technical Requirements6.1 Trademark and Chemical Composition The trademark and chemical composition (smelting analysis) of alloys shall comply with stipulations in Table 1.When the magnetic performance of alloys complies with stipulations in Table 3, the allowable deviation range of chemical composition is shown in Table 1 below. 6.2 Smelting Method Unless it is stipulated otherwise in the contract, the smelting method of alloys shall be selected by the manufacturers. 6.3 State of Delivery 6.4 Magnetic Performance After heat treatment, the magnetic performance of alloy sample shall comply with stipulations in Table 3.Please refer to Appendix A for the recommended sample heat treatment rules. 6.5 Other Performance Please refer to Appendix B for the fundamental physical parameters of alloys and typical performance value of alloy materials in Appendix B.7 Test MethodsTest items and methods of alloys shall comply with stipulations in Table 4 below.8 Inspection Rules8.1 Inspection and Acceptance Check The suppliers’ quality and technical supervision department shall conduct the inspection and acceptance check of alloys. The demanders are entitled to conduct acceptance check in accordance with the requirements in this Part. 8.2 Batch Rules Alloys shall be submitted for inspection and acceptance check by batches. Each batch shall be constituted of alloys of the same trademark, furnace number, specification and state of delivery. 8.4 Re-inspection and Determination Rules 8.4.1 The re-inspection and determination of alloys shall comply with stipulations in GB/T 14986.1-2018.9 Packaging, Mark and Quality CertificatePackaging, mark and quality certificate of alloys shall comply with relevant stipulations in GB/T 14986.1-2018.Appendix A(informative appendix) Recommended Sample Heat Treatment Rules A.1 Generally speaking, sample heat treatment shall be conducted in pure hydrogen (dew point ≤ -40 °C). When vacuum heat treatment is required, residual pressure ≤ 0.1 Pa is recommended. A.2 All the mechanical processes (punching, cutting, winding, deburring, etc.) for sample preparation shall be conducted before heat treatment. Sample shall be degreased and kept clean before heat treatment. After annealing, the surface of the sample shall be smooth. During annealing, no mutual adhesion or mechanical deformation is allowed.Appendix B(informative appendix) Fundamental Physical Parameters and Typical Performance Value of Alloys B.1 Please refer to Table B.1 for the fundamental physical parameters and typical mechanical performance of alloys. B.2 Please refer to Table B.2 for the average linear expansion coefficient of 1J116 alloys in different temperature ranges. ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 14986.4-2018 be delivered?Answer: The full copy PDF of English version of GB/T 14986.4-2018 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 14986.4-2018_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 14986.4-2018_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 14986.4-2018 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.How to buy and download a true PDF of English version of GB/T 14986.4-2018?A step-by-step guide to download PDF of GB/T 14986.4-2018_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 14986.4-2018". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
