GB/T 14415-2007 English PDFUS$139.00 · In stock
Delivery: <= 2 days. True-PDF full-copy in English will be manually translated and delivered via email. GB/T 14415-2007: Water for industrial circulating cooling system and boiler -- Determination of solids matter Status: Valid GB/T 14415: Historical versions
Basic dataStandard ID: GB/T 14415-2007 (GB/T14415-2007)Description (Translated English): Water for industrial circulating cooling system and boiler -- Determination of solids matter Sector / Industry: National Standard (Recommended) Classification of Chinese Standard: G76 Classification of International Standard: 71.040.40 Word Count Estimation: 5,558 Date of Issue: 2007-08-13 Date of Implementation: 2008-02-01 Older Standard (superseded by this standard): GB/T 15893.4-1995; GB/T 14415-1993 Quoted Standard: GB/T 6903 Regulation (derived from): China National Standard Approval Announcement2007 No.8 (Total No.108) Issuing agency(ies): General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China, Standardization Administration of the People's Republic of China Summary: This standard specifies the natural water, industrial cooling water, determination of dissolved solids, boiler water total solids. This standard applies to the determination of the boiler water and industrial cooling water circulating solid material. GB/T 14415-2007: Water for industrial circulating cooling system and boiler -- Determination of solids matter---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order. Water for industrial circulating cooling system and boiler. Determination of solids matter ICS 71.040.40 G76 National Standards of People's Republic of China Replacing GB/T 14415-1993, GB/T 15893.4-1995 Industrial circulating cooling water and boiler water in Determination of solid matter Posted 2007-08-13 2008-02-01 implementation Administration of Quality Supervision, Inspection and Quarantine of People's Republic of China Standardization Administration of China released ForewordThis standard also replace the GB/T 14415-1993 "boiler water and cooling water analysis method of solid substances in the Determination" GB/T 15893.4-1995 "Industrial circulating cooling water of dissolved solids - Gravimetric method." The main difference compared with the standard GB/T 14415-1993 as follows. --- Deletion of the suspended solids measurement method after burning residues and reductions. The main difference compared with the standard GB/T 15893.4-1995 as follows. --- Increased the determination of the total solids. The standard proposed by the People's Republic of China Petroleum and Chemical Industry Association. This standard by the National Standardization Technical Committee of Chemical Water Treatment Chemicals Branch (SAC/TC63/SC5) centralized. This standard was drafted. Tianjin Chemical Engineering Research and Design Institute, China Petroleum & Chemical Corporation water treatment chemicals assessment center. The main drafters of this standard. Shao Hongqian, Jindong, Bai Ying, Li Lin, Zhu Zhuanjun. This standard replaces the standard release case. --- GB/T 14415-1993; --- GB/T 15893.4-1995. Industrial circulating cooling water and boiler water in Determination of solid matter1 ScopeThis standard specifies the natural water, industrial cooling water, boiler water total solids, dissolved solids measurement method. This standard applies to the determination of boiler water and industrial cooling water circulating solid material.2 Normative referencesThe following documents contain provisions which, through reference in this standard and become the standard terms. For dated references, subsequent Amendments (not including errata content) or revisions do not apply to this standard, however, encourage the parties to the agreement are based on research Whether the latest versions of these documents. For undated reference documents, the latest versions apply to this standard. GB/T 6903 boiler water and cooling water General Analysis3 Determination of total solidsThis method is applicable to the total solids content of greater than 25mg/L of natural water, cooling water, water of furnace-like determination. 3.1 Principle In this method, a volume of the water sample, and placed in an evaporating dish of known mass evaporated, transferred 105 ℃ ~ 110 ℃ oven drying to constant. The remaining residue is the resultant of the total solids in water. 3.2 instruments and equipment The following general laboratory instruments and equipment. 3.2.1 evaporating dish. 100mm (platinum, quartz, or porcelain evaporating dish). 3.2.2 water bath. 3.3 Analysis Steps Analysis of the process followed in the relevant provisions of GB/T 6903's. 3.3.1 Wash evaporating dish and placed 105 ℃ ~ 110 ℃ oven drying to constant and set aside. 3.3.2 Pipette a certain amount of water to fully shake sample (total solids content of greater than 25mg) in a known mass of the evaporating dish placed on a steam heater hair. When a large volume of water sample, you can use low-temperature furnace, a hot plate or infrared heating plate evaporation, condensation (be careful not to boil the water sample), not Off additional water sample until the volume was reduced after 20mL ~ 30mL to move to the boiling water bath pot continue evaporated to dryness. In order to prevent impurities in the environment Pollution, should be placed on a tripod in an evaporating dish, and stamped with a watch glass or skirted. Note also that the water bath water can not be connected with the evaporating dish Touch, in order to avoid contamination evaporating dish, affect the measurement results. 3.3.3 The water has evaporated and the residue samples along with evaporating dish placed in an oven 105 ℃ ~ 110 ℃, the drying to constant weight. 3.4 Calculation Results Water samples total solids concentration ρ1 and its value in milligrams per liter (mg/L) said, according to the formula (1). ρ1 = (M1 m1 2- 1) × 106 Vp 1 (1) Where. Value m1 2 --- after drying and evaporation of the total solid mass of the dish in grams (g); Value m1 --- evaporating dish of mass in grams (g); Value Vp 1 --- water sample volume in milliliters (mL). ......Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of GB/T 14415-2007_English be delivered?Answer: Upon your order, we will start to translate GB/T 14415-2007_English as soon as possible, and keep you informed of the progress. The lead time is typically 1 ~ 2 working days. The lengthier the document the longer the lead time.Question 2: Can I share the purchased PDF of GB/T 14415-2007_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 14415-2007_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay.Question 5: Should I purchase the latest version GB/T 14415-2007?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 14415-2007 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically. |
