GB/T 14212-2010 PDF EnglishUS$285.00 · In stock · Download in 9 seconds
GB/T 14212-2010: Motorcycle chains - Characteristics and test methods Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid GB/T 14212: Historical versions
Similar standardsGB/T 14212-2010: Motorcycle chains - Characteristics and test methods---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT14212-2010GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 21.220.30 J 18 GB/T 14212-2010 / ISO 10190.2008 Replacing GB/T 14212-2003 Motorcycle Chains – Characteristics and Test Methods (ISO 10190.2008, IDT) Issued on: JANUARY 10, 2011 Implemented on: OCTOBER 1, 2011 Issued by. General Administration of Quality Supervision, Inspection and Quarantine; Standardization Administration of the People’s Republic of China. Table of ContentsForeword... 3 Introduction... 5 1 Scope... 6 2 Normative References... 6 3 Motorcycle Chains... 6 3.1 Nomenclature of assemblies and components... 6 3.2 Designation... 7 3.3 Dimensions... 8 3.4 Performance requirements... 8 3.5 Marking... 11 4 Sprockets... 12 Annex A (Normative) Alternative Specification of Chain Sprockets for Use in External Drives... 13 Annex B (Informative) Original Values... 21 Annex C (Normative) Method of Determining the Maximum Test Force, Fmax, When Conducting a Dynamic Strength Conformance Test... 22ForewordThis Standard uses translation method to equivalently adopt international standard ISO 10190.2008 Motorcycle Chains – Characteristics and Test Methods. This Standard replaced GB/T 14212-2003 Motorcycle Chains – Characteristics and Test Methods. Compared with GB/T 14212-2003, the major technical changes of this Standard are as follows. --- Add a new table of contents page and ISO introduction; --- Made technical revisions to Figures 1, 2 and 3; and delete a double-row structural diagram; --- Made technical revisions to 3.4.3, adjusting the original pre-tension load value from 1/3 of the minimum tensile strength value to 30%; --- Made technical revisions to 3.4.4, adjusting the original tolerance of the chain measurement length from +0.15 0 % of the nominal length of the chain to +0.25 0 %; --- Cancel the original standard's requirements for dynamic load test; --- Made technical revisions to Table 1, adding dynamic load strength Fd, and cancelling the original standard's provisions for maximum load F1 and minimum load F2 for fatigue test; --- Adopt all new ISO chain numbers in Table 1; add seven new chain specifications, namely. 219H, 415MH, 420MH, 520MH, 525, 525MH, 530MH; cancel 08MB-2 double-row chain; adjust some data in the original Table 1; --- "(0.0009df+0.08), up to 1.14mm" in ISO 10190.2008 Annex A Clause A.7, because the diameter of motorcycle sprockets is not too large, delete "up to 1.14mm" in this Standard adoption; --- Partially adjust and rewrite the NOTE of Table 1; --- Move the Annex A of the original standard to Annex B; --- Add new Annexes A and C. The Annexes A and C of this Standard are normative; while Annex B is informative. This Standard was proposed by China Machinery Industry Federation. This Standard shall be under the jurisdiction of National Technical Committee on Chain Transmission of Standardization Administration of China. Motorcycle Chains – Characteristics and Test Methods1 ScopeThis International Standard specifies the dimensions and mechanical properties of roller and bush chains together with details of associated chain sprockets (see Annex A), in the range 6.35 mm to 19.05 mm pitch, for use in motorcycle applications. These chains are suitable for external drives (e.g., rear drives). It covers dimensions, tolerances, length measurement, preloading, minimum tensile strength and minimum dynamic strength.2 Normative ReferencesThe provisions in following documents become the provisions of this Standard through reference in this Standard. For dated references, the subsequent amendments (excluding corrigendum) or revisions do not apply to this Standard, however, parties who reach an agreement based on this Standard are encouraged to study if the latest versions of these documents are applicable. For undated references, the latest edition of the referenced document applies. GB/T 1243 Short-pitch Transmission Precision Roller and Bush Chains, Attachments and Associated Chain Sprockets (GB/T 1243-2006, ISO 606.2004, IDT) GB/T 1800.2 Geometrical product specifications (GPS) - Limits and fits - Part 2.Tables of standard tolerance grades and limit deviations for holes and shafts (GB/T 1800.2-2009, ISO 286-2.1988, ISO System of limits and fits – Part 2.Tables of standard tolerance grades and limit deviations for holes and shafts, MOD) GB/T 20736 Fatigue test method for transmission precision roller chain (GB/T 20736- 2006, ISO 15654.2004, IDT)3 Motorcycle Chains3.1 Nomenclature of assemblies and components The nomenclature of chain assemblies and their component parts shall be as illustrated in Figures 1 and 2; the figures do not define the actual form of the chain plates. ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 14212-2010 be delivered?Answer: The full copy PDF of English version of GB/T 14212-2010 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 14212-2010_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 14212-2010_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 14212-2010 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.Question 5: Should I purchase the latest version GB/T 14212-2010?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 14212-2010 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically.How to buy and download a true PDF of English version of GB/T 14212-2010?A step-by-step guide to download PDF of GB/T 14212-2010_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 14212-2010". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
