GB/T 13508-2011 English PDFUS$299.00 · In stock
Delivery: <= 3 days. True-PDF full-copy in English will be manually translated and delivered via email. GB/T 13508-2011: Polyethylene blown containers Status: Valid GB/T 13508: Historical versions
Basic dataStandard ID: GB/T 13508-2011 (GB/T13508-2011)Description (Translated English): Polyethylene blown containers Sector / Industry: National Standard (Recommended) Classification of Chinese Standard: A82 Classification of International Standard: 83.140 Word Count Estimation: 13,121 Date of Issue: 2011-12-30 Date of Implementation: 2012-09-01 Older Standard (superseded by this standard): GB/T 13508-1992 Quoted Standard: GB/T 2828.1-2003; GB/T 16288 Regulation (derived from): Announcement of Newly Approved National Standards No. 23 of 2011 Issuing agency(ies): General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China, Standardization Administration of the People's Republic of China Summary: This standard specifies the structure of polyethylene blow molded container products, specifications, requirements, test methods, inspection rules, marking, packaging, transport and storage. This standard applies to polyethylene as the main raw material, the use of blow molding process has a capacity of 250L or less (including 250L) Filling temperature below 50��C, storage temperature below 40��C plastic bottles, cans, buckets (hereinafter referred to as the container). 250L more blow molded containers can refer to this standard. This standard does not apply to dangerous goods, food packaging containers. GB/T 13508-2011: Polyethylene blown containers---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order.Polyethylene blown containers ICS 83.140 A82 National Standards of People's Republic of China Replacing GB/T 13508-1992 Polyethylene blow molded containers Issued on. 2011-12-30 2012-09-01 implementation Administration of Quality Supervision, Inspection and Quarantine of People's Republic of China Standardization Administration of China released ForewordThis standard GB/T 1.1-2009 given rule drafting. This standard replaces GB/T 13508-1992 "polyethylene blow barrels." This standard compared with GB/T 13508-1992 main changes are as follows. --- Standard name changed to "polyethylene blow molded containers"; --- Expand the capacity of the standard scope; clearly this standard does not apply to dangerous goods, food packaging containers; --- Increasing the permeability of the mouth, the packaging container cover structure; the line level and multi-vessel container; --- Increased provision handle container structure, shape, large and small diameter; --- Increasing the capacity of the test method bias; --- Modify the capacity of deviation, quality deviation, size deviation, symmetric parts and minimum wall thickness ratio, built-in resistance to fluid test requirements; --- Modify the drop test; --- Modify the decision rule and sampling programs; --- Removed classification; --- Remove Appendix A. The standard proposed by China National Light Industry Council. This standard by the National Plastics Standardization Technical Committee (SAC/TC48) centralized. This standard was drafted. Foshan Nanhai Dongxing Plastic Can Co., Ltd., light industry Institute of Plastics Processing Applications, Nanhai District of Foshan City, Standardization Research and Promotion Center. The main drafters of this standard. Loewe since, Shaw collar, Lijie Tao, Pangqi Xiong, Liang Guangwei, Zhou Yu Qiang, Li Xian sword. This standard replaces the standards previously issued as follows. --- GB/T 13508-1992. Polyethylene blow molded containers1 ScopeThis standard specifies the structure of the product, specifications, requirements, test methods, inspection rules polyethylene blow molded containers, signs, packaging, transport and Storage. This standard applies to polyethylene as the main raw material, the blow molding process a volume of 250L or less (including 250L) Filling use temperature The following degrees 50 ℃, storage temperature below 40 ℃ plastic bottles, cans, drums (hereinafter referred to as the container). 250L above blow molded containers can refer to this standard. This standard does not apply to dangerous goods, food packaging containers.2 Normative referencesThe following documents for the application of this document is essential. For dated references, only the dated version suitable for use herein Member. For undated references, the latest edition (including any amendments) applies to this document. GB/T 2828.1-2003 Sampling procedures for inspection - Part 1. by acceptance quality limit (AQL) retrieval batch test sample plan GB/T 16288 plastic signs3 Product Structure3.1 caliber Into open-ended and closed type two, into an opening diameter greater than 70mm formula, is not more than 70mm diameter injection of closed type. use In containers containing liquid formula should be closed. 3.2 handle Integral points, and the end-mounted hands-down. Outfitted. one blow molding; mounted. After blow molding in a fixed part of the assembly; hand-side Type. blow molding for moving irregularities site. 3.3, cover Into using threads or other structures. 3.4 Level Line According to the demand and supply sides negotiate if there are line level and location. 3.5 multilayered container Two-layer coextrusion blow molding process made (or more) of the container. ......Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of GB/T 13508-2011_English be delivered?Answer: Upon your order, we will start to translate GB/T 13508-2011_English as soon as possible, and keep you informed of the progress. The lead time is typically 1 ~ 3 working days. The lengthier the document the longer the lead time.Question 2: Can I share the purchased PDF of GB/T 13508-2011_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 13508-2011_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay.Question 5: Should I purchase the latest version GB/T 13508-2011?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 13508-2011 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically. |
