GB/T 1190-2018 English PDFUS$119.00 ยท In stock
Delivery: <= 3 days. True-PDF full-copy in English will be manually translated and delivered via email. GB/T 1190-2018: Technical specification of earth-mover tyres Status: Valid GB/T 1190: Historical versions
Basic dataStandard ID: GB/T 1190-2018 (GB/T1190-2018)Description (Translated English): Technical specification of earth-mover tyres Sector / Industry: National Standard (Recommended) Classification of Chinese Standard: G41 Classification of International Standard: 83.160.99 Word Count Estimation: 6,631 Date of Issue: 2018-12-28 Date of Implementation: 2019-11-01 Older Standard (superseded by this standard): GB/T 1190-2009 Issuing agency(ies): State Administration for Market Regulation, China National Standardization Administration GB/T 1190-2018: Technical specification of earth-mover tyres---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order.Technical specification of earth--mover tyres ICS 83.160.99 G41 National Standards of People's Republic of China Replaces GB/T 1190-2009 Technical requirements for construction machinery tires 2018-12-28 release 2019-11-01 Implementation State Administration of Market Supervision Published by China National Standardization Administration ForewordThis standard was drafted in accordance with the rules given in GB/T 1.1-2009. This standard replaces GB/T 1190-2009 "Technical Requirements for Tires for Construction Machinery". Compared with GB/T 1190-2009, The main technical changes outside the reform are as follows. --- Increased normative references GB/T 30193 (see Chapter 2); --- Increased the provision that the surface of the radial tires is not allowed to expose the cord (see 4.1.2); --- Explained the physical strength requirements of tires that are not suitable for steel cord adhesive strength indicators (see Table 1); --- Increased requirements regarding tire durability (see 4.3); --- The test method has added the provisions of the durability test method (see 5.5); --- Removed the regulations on measuring the rim in the tire mark (see 6.1 of the.2009 edition); --- Added the requirement that tires implanted with radio frequency identification (RFID) tags should have permanent electronic tag marking (see 6.1.3); --- Added the rule that radial tires should be engraved with "RADIAL" (see 6.1.4). This standard was proposed by the China Petroleum and Chemical Industry Federation. This standard is under the jurisdiction of the National Tire and Rim Standardization Technical Committee (SAC/TC19). This standard was drafted. Fengshen Tire Co., Ltd., Zhongce Rubber Group Co., Ltd., Xuzhou Xulun Rubber Co., Ltd., Tianjin Guoxian International Union Tire & Rubber Co., Ltd., Shandong Linglong Tire Co., Ltd., Anhui Jiatong Passenger Radial Tire Co., Ltd., Triangle Tire Co., Ltd., Beijing Rubber Industry Research and Design Institute Co., Ltd., Shuangqian Tire Group Co., Ltd., Guizhou Tire Co., Ltd. Division, Jiangsu General Technology Co., Ltd., Zhejiang Ketaian Tire Co., Ltd., Michelin (China) Investment Co., Ltd., Continental Horse Tyre (China) Co., Ltd., Dalian Goodyear Tire Co., Ltd., Shantou Haoda Tire Testing Equipment Co., Ltd. The main drafters of this standard. Wang Zhiping, Mao Jianqing, Pei Xiaohui, Wang Lijun, Chen Shaomei, Wang Linfeng, Sun Hongsha, Wang Kexian, Mu Shouyong, Cai Lichao, Yang Shichun, Ding Zhenhong, Xia Huan, Lu Yi, Ma Zhong, Yin Qingye, Chen Xun. The previous versions of the standards replaced by this standard are. --- GB/T 1190-1974, GB/T 1190-1982, GB/T 1190-1991, GB/T 1190-2001, GB/T 1190-2009. Technical requirements for construction machinery tires1 ScopeThis standard specifies the terms and definitions, requirements, test methods, marking and packaging, use and maintenance of construction machinery tires. This standard applies to new construction machinery pneumatic tires (including tires, inner tubes and cushion belts).2 Normative referencesThe following documents are essential for the application of this document. For dated references, only the dated version applies to this article Pieces. For undated references, the latest version (including all amendments) applies to this document. GB/T 519 Test method for physical properties of pneumatic tires GB/T 521 Tire outer edge measurement method GB/T 528 Determination of tensile stress and strain properties of vulcanized rubber or thermoplastic rubber GB/T 531.1 Test method for indentation hardness of vulcanized rubber or thermoplastic rubber Part 1. Shore hardness tester (Shore hardness) GB/T 532 Determination of the bonding strength between vulcanized rubber or thermoplastic rubber and fabric GB/T 1689 Determination of abrasion resistance of vulcanized rubber (using Akron abrasion tester) GB/T 2980 Engineering machinery tire specifications, dimensions, air pressure and load GB/T 6326 tire terms and definitions GB/T 9768 Tire use and maintenance regulations GB/T 30193 Test method for durability of construction machinery tires HG/T 2177 tire appearance quality3 terms and definitionsThe terms and definitions defined in GB/T 6326 and GB/T 2980 apply to this document.4 Requirements4.1 Basic requirements 4.1.1 The specification, size, air pressure and load of the tire, the type of use of the tire, and the classification code of the pattern should conform to GB/T 2980 or related technologies Documentation requirements. 4.1.2 Various tires are not allowed to have defects that seriously affect the service life, such as delamination between components, sponge-like, traveller breakage and severe Defects such as pumping, broken and split multiple cords, pleated cords in the tires, and cords with rubber edges in the tire crown. Exposed. If a pad is used, the pad is not allowed to be defective in appearance and cracked. 4.1.3 Other appearance quality requirements of tires and pads shall meet the requirements of HG/T 2177. 4.1.4 If inner tubes and pads are used, they shall meet the requirements for matching with outer tubes. 4.2 Physical properties of tires The physical properties of the tire shall meet the requirements in Table 1. Table 1 Physical properties of tires 4.3 Tire durability After the tire has undergone the durability test, the tire air pressure should not be lower than the specified initial air pressure; after the test, the appearance inspection should not be performed (tread, Sidewall, ply, airtight layer, belt or buffer layer, bead, etc.) delamination, ply crack, cord peeling, cord break, chipping, joint crack Opening, cracking, and abnormal deformation of the tire.5 Test method5.1 The tensile strength and elongation at break of the tire tread rubber are sampled according to GB/T 519, and type 2 cutters are used according to GB/T 528. experimenting. 5.2 Abrasion of tire tread rubber is sampled according to GB/T 519 and tested in accordance with GB/T 1689. 5.3 The adhesion strength between the various components of the tire is sampled according to the provisions of GB/T 519, and tested according to the provisions of GB/T 532. 5.4 The hardness of the tire tread rubber is sampled in accordance with GB/T 519 and tested in accordance with GB/T 531.1. 5.5 The tire durability can be tested in accordance with GB/T 30193. 5.6 The tensile strength, elongation at break and permanent deformation at break of the belt shall be sampled in accordance with GB/T 519 and used in accordance with GB/T 528. The test specimens cut by a profile cutter are tested. 5.7 The outer edge size of a new tire after inflation is measured in accordance with GB/T 521.6 Marking and packaging6.1 Signs 6.1.1 Each tire shall have the signs a) ~ h) on the sidewall; each pad shall have the signs a), b) and g). a) specifications; b) trademark, manufacturer name or place of origin; c) level or load symbol or load index; d) name or code of tire frame material, pattern classification code; e) Tubeless tires shall be marked as "tubeless" or "TUBELESS"; f) tyre running direction sign (the tread pattern of the tire has the driving direction); g) factory inspection mark; h) Production number. 6.1.2 The markings on 6.1.1a) ~ f) on the tire shall use the engraved marks. Other markings can be washed with water. 6.1.3 Tires implanted with radio frequency identification (RFID) tags shall have permanent electronic tag marks. 6.1.4 Radial tires shall be engraved with the "RADIAL" or "radial" logo. 6.2 Packaging For tires with inner tubes and pads, the inner tubes and pads should be installed in the outer tube when matching, and the inner tube should be filled with an appropriate amount of air to make it compatible with the inner tube. The inner edges of the tires are in contact with each other, and they are bundled in two or more places or packed according to user requirements.7 Use and maintenanceThe use and maintenance of tires shall comply with the requirements of GB/T 9768.8 Transition periodFor the provisions of 6.1.3 and 6.1.4, the transition period is 24 months from the date of implementation of this standard. ......Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of GB/T 1190-2018_English be delivered?Answer: Upon your order, we will start to translate GB/T 1190-2018_English as soon as possible, and keep you informed of the progress. The lead time is typically 1 ~ 3 working days. The lengthier the document the longer the lead time.Question 2: Can I share the purchased PDF of GB/T 1190-2018_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 1190-2018_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay.Question 5: Should I purchase the latest version GB/T 1190-2018?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 1190-2018 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically. |
