GB/T 11313.35-2021 English PDFUS$414.00 · In stock
Delivery: <= 3 days. True-PDF full-copy in English will be manually translated and delivered via email. GB/T 11313.35-2021: Radio-frequency connectors - Part 35: Sectional specification for 2.92 series R. F. connectors Status: Valid
Basic dataStandard ID: GB/T 11313.35-2021 (GB/T11313.35-2021)Description (Translated English): Radio-frequency connectors - Part 35: Sectional specification for 2.92 series R. F. connectors Sector / Industry: National Standard (Recommended) Classification of Chinese Standard: L23 Word Count Estimation: 22,250 Issuing agency(ies): State Administration for Market Regulation, China National Standardization Administration GB/T 11313.35-2021: Radio-frequency connectors - Part 35: Sectional specification for 2.92 series R. F. connectors---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order. Radio-frequency connectors - Part 35.Sectional specification for 2.92 series RFconnectors ICS 33.120 L23 National Standards of People's Republic of China RF connector Part 35.Sectional Specification for 2.92 Series RF Connectors (IEC 61169-35.2011, IDT) Released on 2021-03-09 2021-10-01 implementation State Administration of Market Supervision and Administration Issued by the National Standardization Management Committee Table of contentsForeword Ⅰ 1 Scope 1 2 Normative references 1 3 Mating interface and standard gauge 1 3.1 High-performance connector size-level 1 1 3.1.1 Pin connector 1 3.1.2 Jack connector 2 3.2 Standard gauge 3 3.2.1 Standard gauges for jack connectors 3 3.2.2 Test procedure 4 3.3 Standard test connector size --0 level 4 3.3.1 Pin standard test connector 4 3.3.2 Jack standard test connector 5 4 Quality assessment procedures 6 4.1 General 6 4.2 Ratings and characteristics (see Chapter 6 of GB/T 11313.1-2013) 6 4.3 Test list and inspection requirements 9 4.3.1 Delivery test 9 4.3.2 Periodic test 10 4.4 Procedure 11 4.4.1 Quality consistency inspection 11 4.4.2 Approval and maintenance of appraisal 11 5 Guidelines for the development of detailed specifications 11 5.1 General Rule 11 5.2 Identification of detailed specifications 11 5.3 Identification of components 12 5.4 Performance 12 5.5 Marks, order documents and related matters 12 5.6 Selection of test, test conditions and severity 12 5.7 Blank detail specification format for 2.92 series RF connectors 12 Reference 17ForewordGB/T 11313 "Radio Frequency Connectors" has or plans to publish the following parts. ---Part 1.General requirements and test methods of the general specification; ---Part 2.Sectional specification for type 9.52 radio frequency coaxial connectors; ---Part 3.Sectional specification for double-pin connectors for double-balanced antenna feeders; ---Part 4.RF coaxial connector with inner diameter of outer conductor of 16mm (0.63in), characteristic impedance of 50Ω, threaded connection (7-16 type); ---Part 5.Sectional specification for radio frequency coaxial connectors for mating with 60096IEC 50-17 and larger cables; ---Part 6.Sectional specification for radio frequency coaxial connectors for mating with 60096IEC 75-17 and larger cables; ---Part 7.RF coaxial connector with inner diameter of outer conductor of 9.5mm (0.374in), characteristic impedance of 50Ω, bayonet connection (Type C) Sub-specification; ---Part 8.RF coaxial connection with inner diameter of outer conductor of 6.5mm (0.256in), characteristic impedance of 50Ω (75Ω), bayonet connection Connector (BNC type) section specification; ---Part 9.SMC series radio frequency coaxial connector sub-specification; ---Part 10.Sectional specification for SMB series radio frequency coaxial connectors; ---Part 11.RF coaxial connector with inner diameter of outer conductor of 9.5mm (0.374in), characteristic impedance of 50Ω, threaded connection (4.1/9.5 type) sub-specification; ---Part 12.Sectional specification for non-matching threaded radio frequency coaxial connectors (UHF type); ---Part 13.1.6/5.6 and 1.8/5.6 type radio frequency coaxial connector sub-specification; ---Part 14.The inner diameter of the outer conductor is 12mm (0.472in), the characteristic impedance is 75Ω, and the threaded radio frequency coaxial connector (3.5/12 type) sub-specification; ---Part 15.RF coaxial connector with inner diameter of outer conductor of 4.13mm (0.163in), characteristic impedance of 50Ω, threaded connection (SMA type); ---Part 16.The inner diameter of the outer conductor is 7mm (0.276in), the characteristic impedance is 50Ω (75Ω), and the threaded radio frequency coaxial connection Sectional specification for connectors (Type N); ---Part 17.RF coaxial connector with inner diameter of outer conductor of 6.5mm (0.256in), characteristic impedance of 50Ω, threaded connection (TNC type) sub-standard; ---Part 18.Sectional specification for SSMA series radio frequency coaxial connectors; ---Part 19.Sectional specification for SSMB type radio frequency coaxial connectors; ---Part 20.RF coaxial connector with inner diameter of outer conductor of 2.08mm (0.082in), characteristic impedance of 50Ω, threaded connection (SSMC type) sub-specification; ---Part 21.The inner diameter of the outer conductor is 9.5mm (0.374in), the characteristic impedance is 50Ω, and there are two different types of threaded connections The sub-specification of the radio frequency connector (SC-A and SC-B type); ---Part 22.Sectional specification for double core radio frequency connectors (BNO type) for bayonet connection of double inner conductor shielded symmetrical cables; ---Part 23.Connecting 3.5mm hard precision coaxial cable, the inner diameter of the outer conductor is 3.5mm (0.1378in) radio frequency coaxial connector specification; ---Part 24.Sectional specification for threaded radio frequency coaxial connectors (Type F) for 75Ω cable distribution systems; ---Part 25.Connect double inner conductor shielded symmetrical cable, outer conductor inner diameter of 13.56mm (0.534in) twin core thread type (3/4- 20UNEF) connector (TWHN type) section specification; ---Part 26.TNCA series radio frequency coaxial connector sub-specification; ---Part 27.Sectional specification for threaded radio frequency coaxial connectors (Type E) for 75Ω cable distribution systems; ---Part 28.The inner diameter of the outer conductor is 5.60mm (0.220in), the characteristic impedance is 75Ω, and the card lock is connected to the radio frequency coaxial connector. specification; ---Part 29.50Ω and 75Ω with characteristic impedance of 50Ω, with threaded, push-pull, quick lock or slide rail rack or panel with small Sectional specification for type radio frequency coaxial connectors (1.0/2.3 type); ---Part 31.RF coaxial connector with inner diameter of outer conductor of 1.0mm (0.039in), characteristic impedance of 50Ω, threaded connection (1.0 type) sub-standard; ---Part 32.RF coaxial connector with inner diameter of outer conductor of 1.85mm (0.072in), characteristic impedance of 50Ω, threaded connection (1.85 type) sub-specification; ---Part 33.Sub-specification for BMA series radio frequency connectors; ---Part 35.2.92 series radio frequency connector sub-specification; ---Part 36.Snap-on miniature radio frequency coaxial connector (MCX type) with characteristic impedance of 50Ω; ---Part 37.STWX8 series radio frequency coaxial connector sub-specification; ---Part 38.Sectional specification for 50Ω backplane and panel modular sliding-in radio frequency connectors (TMA type); ---Part 39.Sectional Specification for CQM Series Quick Lock RF Connectors; ---Part 40.2.4 series radio frequency connector sub-specification; ---Part 41.Sectional Specification for CQA Series Quick Lock RF Connectors; ---Part 42.Sectional Specification for CQN Series Quick Lock RF Connectors; ---Part 43.Sectional specification for RBMA series blind-mate radio frequency coaxial connectors; ---Part 44.Sectional specification for SMP series push-in radio frequency coaxial connectors; ---Part 45.Sectional Specification for SQMA Series Quick Lock RF Coaxial Connectors; ---Part 47.Sectional specification for plug-in radio frequency coaxial connectors for Fquick series 75Ω cable distribution systems; ---Part 48.BMP series blind-mate radio frequency coaxial connector sub-specification; ---Part 49.SMAA series radio frequency coaxial connector sub-specification; ---Part 58.Sectional specification for SBMA series blind-mate radio frequency coaxial connectors; ---Part 101.Sectional specification for MMCX series radio frequency coaxial connectors; ---Part.201.Electrical test method reflection coefficient and voltage standing wave ratio; --- Part 202.Electrical test method insertion loss. This part is Part 35 of GB/T 11313. This section was drafted in accordance with the rules given in GB/T 1.1-2009. The translation method used in this part is equivalent to the use of IEC 61169-35.2011 "Radio Frequency Connector Part 35.2.92 Series of RF Connectors specification". This section has made the following editorial changes. ---Regulate the statement in paragraph 4 of the scope; ---The direction of the h dimension in Figure 1 and Figure 4 is changed from the pin step to the mechanical and electrical reference plane; ---Add a sealing ring in Figure 1, and explain in Note 5 and Note 6; --- Add "a" to the frequency range in Table 6, and delete "the upper limit frequency of the cable"; ---Unify the cable names in Table 6; ---In Table 6, the strength of the connecting mechanism is adjusted from 100N to 266.9N; ---The content of Chapter 5 and other standards are unified and standardized. Please note that some of the contents of this document may involve patents. The issuing agency of this document is not responsible for identifying these patents. This part was proposed by the Ministry of Industry and Information Technology of the People's Republic of China. This part is under the jurisdiction of the National Standardization Technical Committee for High-frequency Cables and Connectors for Electronic Equipment (SAC/TC190). This section was drafted by. Shaanxi Huada Technology Co., Ltd., China Electronics Standardization Institute. The main drafters of this section. Wang Rongxin, Guo Yan, Wu Zhengping. RF connector Part 35.Sectional Specification for 2.92 Series RF Connectors1 ScopeThis part of GB/T 11313 provides the content and rules for formulating detailed specifications for 2.92 series radio frequency coaxial connectors, as well as detailed specifications. Fan’s blank format. This part also specifies the size of the mating interface of the level 1 high-performance connector, the detailed size of the level 0 standard test connector, and the The content of rules and test procedures selected in GB/T 11313.1-2013 applicable to all detailed specifications of 2.92 series connectors. This part also specifies the recommended ratings and characteristics that should be considered when compiling detailed specifications, and specifies that they are applicable to M-level and H-level evaluations. Level test list and inspection requirements. The 2.92 series connector has a characteristic impedance of 50Ω, the inner diameter of the outer conductor is 2.92mm, and the threaded connection is used for millimeter wave and is used for radio frequency. Cable or microstrip. The frequency of use of this connector is at least 40GHz. 2.92 series connector interface standards are similar to IEEEStd287-2007 (2.92mm) and MIL-STD-348A (SMK). 2.92 The connector can be used with the SMA series (SMA. IEC 61169-35, MIL-PRF-39012D and MIL-STD-348A) and 3.5mm series (3.5mm. IEC 60169-23, IEEEStd287-2007) connectors are mutually mated.2 Normative referencesThe following documents are indispensable for the application of this document. For dated reference documents, only the dated version applies to this article Pieces. For undated reference documents, the latest version (including all amendments) is applicable to this document. GB/T 11313.1-2013 Radio Frequency Connector Part 1.General Specification General Requirements and Test Methods (IEC 61169-1. 1998, IDT)3 Mating interface and standard gauge3.1 High-performance connector size-level 1 3.1.1 Pin connector The pin connector is shown in Figure 1 and Table 1.All graphic structures without dimensions are for reference only. Note. The original size is inches. ......Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of GB/T 11313.35-2021_English be delivered?Answer: Upon your order, we will start to translate GB/T 11313.35-2021_English as soon as possible, and keep you informed of the progress. The lead time is typically 1 ~ 3 working days. The lengthier the document the longer the lead time.Question 2: Can I share the purchased PDF of GB/T 11313.35-2021_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 11313.35-2021_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay. |
