GB 28132-2011 English PDFUS$259.00 · In stock
Delivery: <= 3 days. True-PDF full-copy in English will be manually translated and delivered via email. GB 28132-2011: [GB/T 28132-2011] Imidacloprid micro-emulsion Status: Valid
Basic dataStandard ID: GB 28132-2011 (GB28132-2011)Description (Translated English): [GB/T 28132-2011] Imidacloprid micro-emulsion Sector / Industry: National Standard Classification of Chinese Standard: G25 Classification of International Standard: 65.100.10 Word Count Estimation: 10,183 Date of Issue: 2011-12-30 Date of Implementation: 2012-04-15 Quoted Standard: GB/T 1601; GB/T 1603; GB/T 1604; GB/T 1605-2001; GB 4838; GB/T 14825; GB/T 19136; GB/T 19137 Regulation (derived from): Announcement of Newly Approved National Standards No. 23 of 2011 Issuing agency(ies): General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China, Standardization Administration of the People's Republic of China Summary: This Chinese standard specifies the imidacloprid microemulsion requirements, test methods and marking, labeling, packaging, storage, security and guarantee period. This standard applies to imidacloprid, water and additives made of imidacloprid microemulsion. GB 28132-2011: [GB/T 28132-2011] Imidacloprid micro-emulsion---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order.Imidacloprid micro-emulsion ICS 65.100.10 G25 National Standards of People's Republic of China Imidacloprid microemulsion Issued on. 2011-12-30 2012-04-15 implementation Administration of Quality Supervision, Inspection and Quarantine of People's Republic of China Standardization Administration of China released ForewordThe standard Chapter 3, Chapter 5 is mandatory, the rest are recommended. This standard was drafted in accordance with GB/T 1.1-2009 given rules. Please note that some of the content of this document may involve patents. Release mechanism of the present document does not assume responsibility for the identification of these patents. The standard proposed by China Petroleum and Chemical Industry Association. This standard by the National Standardization Technical Committee on Pesticides (SAC/TC133) centralized. This standard is drafted by. Shenyang Chemical Research Institute Co., Ltd. Participated in the drafting of this standard. Shenzhen Knopp letter Agrochemical Co., Ltd., Shandong Mega Biotech Co., Ltd., Jiangsu Changqing Agrochemical Copper Co., Ltd., Qingdao Hailier Pharmaceutical Co., Ltd. The main drafters of this standard. Hou Chunqing, Zan Yan Kun, Fang Yuan volts, and Jerry Shannon, Lixue Chen, Yang Hua. Imidacloprid microemulsion1 ScopeThis standard specifies the imidacloprid microemulsion requirements, test methods and marking, labeling, packaging, storage, security and guarantee period. This standard applies to imidacloprid imidacloprid by a micro-emulsion, water and additives made of. Note. Other name, structural formula and basic physicochemical parameters of imidacloprid in Appendix A.2 Normative referencesThe following documents for the application of this document is essential. For dated references, only the dated version suitable for use herein Member. For undated references, the latest edition (including any amendments) applies to this document. Determination of GB/T 1601 Pesticides pH value GB/T 1603 Determination of emulsion stability of pesticide GB/T 1604 Goods pesticide regulations for acceptance GB/T 1605-2001 Sampling Method commercial pesticides GB 4838 EC pesticide packaging GB/T 14825 method for determination of pesticide suspension GB/T 19136 Determination of Pesticide Thermal storage stability GB/T 19137 Pesticide cryogenic stability Determination3 Requirements3.1 Composition and appearance This product should be compliant imidacloprid, water and suitable additives made, should be transparent or translucent homogeneous liquid without visible suspended Float and precipitates. 3.2 Technical Specifications Imidacloprid microemulsion should meet the requirements of Table 1. Table 1 imidacloprid microemulsion quality control program indicators Item Index Imidacloprid mass fraction /% 20.0 10.0 1.0 to 1.0 1.2 -1.2 pH range of 5.0 to 8.0 Transparent test temperature range (0 ℃ ~ 50 ℃) qualified Emulsion stability (diluted 500 times) Qualified (After 1min) Persistent foaming/mL ≤ 25 Thermal storage stability of a qualified Low temperature stability a qualified When a normal production, thermal storage stability, low-temperature stability test was measured at least once every three months. Test Method 4 4.1 Sampling According to GB/T 1605-2001 in "liquid formulations sampling" approach. Determining sample package using a random number table method; the final sample size Not less than 200mL. 4.2 Identification Test Liquid chromatography --- The identification test can be carried out simultaneously with the determination of the mass fraction of imidacloprid. Under the same chromatographic operating conditions, the test The retention time of the sample solution and the standard solution to a peak of imidacloprid chromatographic retention time, the relative difference should be 1.5% Fewer. 4.3 Determination of the mass fraction of imidacloprid 4.3.1 Method summary Sample dissolved in mobile phase, methanol and water as the mobile phase, use as filler to C18 stainless steel column and UV detector at a wavelength 260nm, the sample of imidacloprid reverse phase HPLC separation and determination of external standard. 4.3.2 Reagents and solutions Methanol. HPLC grade; Water. The new secondary steam distilled water; Imidacloprid standard. a known mass fraction w≥99.0%. 4.3.3 Instruments High performance liquid chromatography. a variable wavelength UV detector; Chromatographic data processor or chromatography workstation; Column. 250mm × 4.6mm (id) stainless steel column contents C18,5μm filler; Filter. filter pore size of about 0.45μm; Micro injector. 50μL; Quantitative sample line. 5μL; Ultrasonic cleaner. 4.3.4 HPLC operating conditions Mobile phase. Ψ (methanol. water) = 40.60, by membrane filtration, and degassing; Flow rate. 0.8mL/min; Column temperature. room temperature (temperature change should not exceed 2 ℃); Detection wavelength. 260nm; Injection volume. 5μL; Retention time. about imidacloprid 6.0min. It said operating parameters are typical, according to the characteristics of different instruments, given operating parameters adjusted as appropriate, in order to obtain the best results. Typical imidacloprid microemulsion HPLC is shown in Figure 1. 1 --- imidacloprid. Figure 1 imidacloprid microemulsion HPLC diagram 4.3.5 measuring step 4.3.5.1 Preparation of standard solution Weigh 0.1g (accurate to 0.0002g) imidacloprid standard in 100mL flask, dissolved in methanol and diluted to the mark, ultrasonic Oscillation 5min make sample dissolution, cooled to room temperature and shake well. Using a pipette to take the above solution 5mL to 50mL volumetric flask, with the mobile Phase and dilute to the mark. 4.3.5.2 Preparation of sample solution Weigh containing imidacloprid 0.1g (accurate to 0.0002g) sample in 100mL flask, dissolved in methanol and diluted to the mark, ultra Acoustic oscillations 5min make sample dissolution, cooled to room temperature and shake well. Using a pipette to take the above solution 5mL to 50mL volumetric flask Mobile phase and dilute to the mark. 4.3.5.3 Determination Under these operating conditions, after the instrument is stable, continuous injection of several doses of the standard solution until the two adjacent needles Imidacloprid peak area relative change After less than 1.2%, according to the solution, the sample solution, the sample solution and standard sequence of the standard solution was measured. 4.3.5.4 Calculation Imidacloprid sample mass fraction according to formula (1). w1 = A2 · M1 · w A1 · m2 (1) Where. w1 --- sample imidacloprid mass fraction, expressed as a percentage; A2 --- sample solution, imidacloprid mean peak area; m1 --- standard mass in grams (g); w --- imidacloprid standard mass fraction, expressed as a percentage; A1 --- the standard solution, the average peak area imidacloprid; m2 --- sample mass, in grams (g). 4.3.6 allowable difference Imidacloprid content parallel determination of the difference between the results, 10% of the microemulsion should be less than 0.5%; 20% of the micro-emulsion should not exceed 0.8% The arithmetic mean value as a measurement result. 4.4 transparent test temperature range Samples of 10mL in a 25mL test tube fitted with a thermometer, stirring with a stirring rod and down, placing the tubes on ice-water bath, the temperature control Maintaining 0 deg.] C, the samples were observed whether turbidity, tubes were again placed in a water bath for 2 ℃/min speed slowly warmed to 50 ℃, View Record Examine whether the samples appear cloudy. It does not appear in the range of 0 ~ 50 ℃ cloudy qualified. Determination of 4.5 pH value According to GB/T 1601 carried out. 4.6 Emulsion stability test The sample was diluted 500-fold, according to GB/T 1603 test, the non-oil slick, no precipitation under qualified. 4.7 Persistent foaming test 4.7.1 Method summary The sample was mixed with a predetermined amount of standard hard water, after standing foam volume recorded. 4.7.2 Reagents Standard hard water. ρ (Ca2 Mg2) = 342mg/L, pH = 6.0 ~ 7.0, according to GB/T 14825 preparation. 4.7.3 Instruments and Appliances Stoppered cylinder. 250mL (division value 2mL, 0 ~ 250mL tick 20cm ~ 21.5cm, 250mL scale line to the bottom plug 4cm ~ 6cm); Industrial scale. a sense of the amount of 0.1g. 4.7.4 measuring step Added 180mL graduated cylinder standard hard water, 1.0g sample was weighed into a graduated cylinder (accurate to 0.1g), added to standard hard water from the cylinder Plug at the bottom tick 9cm, the cover plug to the bottom of the cylinder as the center, upside down 30 times (2s). Stand on the test stand 1min, record lather volume. 4.8 Thermal storage stability test According to GB/T 19136 in "liquid formulation" to. After the heat storage imidacloprid content should not be less than 97% before storage, emulsion stability still It shall meet the standards. 4.9 Low temperature stability test According to GB/T 19137 in "homogeneous emulsion and liquid preparations" to. 7d after removing the beaker returned to room temperature, with gentle agitation, there should be no visible Particles and oil. 4.10 Product inspection and acceptance Shall comply with GB/T 1604's. Treatment of extreme values using the rounding value comparison method. 5 marking, labeling, packaging, storage, security, guarantee 5.1 marking, labeling, packaging Imidacloprid microemulsion marking, labeling and packaging should comply with the provisions of GB 4838. Imidacloprid microemulsion with applications within the plug and the outer cover Brown glass bottle or PET bottle packaging, bottle net content is generally 100g, 500g, etc; corrugated packaging boxes or plastic boxes, each containing a net An amount of not more than 10kg. Also available upon request or order agreement other forms of packaging, subject to the provisions of GB 4838. 5.2 Storage Imidacloprid microemulsion package should be stored in well-ventilated, dry coffers. Storage and transportation to prevent moisture and sun, not with food, seeds, Feed-mixing, avoid contact with skin, eyes, mouth and nose to prevent inhalation. 5.3 Security This product is a low toxicity formulation. It can penetrate through the skin. When using this product to avoid contact with skin, use soap and water after application. Poisoning should immediately sent to hospital symptomatic treatment. 5.4 Warranty Period Under the specified storage conditions, warranties of imidacloprid microemulsion two years starting from the date of manufacture.Appendix A(Informative) Other name, structural formula and basic physicochemical parameters of imidacloprid Other name, structural formula and basic physicochemical parameters of the active ingredient imidacloprid product are as follows. ISO common name. Imidacloprid CAS Registry Number. 138261-41-3 CIPAC Numeric Code. 582 Chemical name. 1- (6-chloro-3-pyridylmethyl) -N- nitromethylene-imidazol-2-yl-amine Structure. Empirical formula. C9H10ClN5O2 Molecular Weight. 255.7 Biological activity. Insecticidal Melting point. 144 ℃ Vapor pressure (20 ℃). 4 × 10-7mPa Solubility (20 ℃, g/L). Water 0.61 0.68 toluene, methylene chloride 55, 1.2 isopropanol, n-hexane is less than 0.1 Stability. pH value of 5 to 11 stable, easy hydrolysis. ......Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of GB 28132-2011_English be delivered?Answer: Upon your order, we will start to translate GB 28132-2011_English as soon as possible, and keep you informed of the progress. The lead time is typically 1 ~ 3 working days. The lengthier the document the longer the lead time.Question 2: Can I share the purchased PDF of GB 28132-2011_English with my colleagues?Answer: Yes. The purchased PDF of GB 28132-2011_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay. |
