GB 19651.3-2008 English PDFUS$209.00 · In stock
Delivery: <= 3 days. True-PDF full-copy in English will be manually translated and delivered via email. GB 19651.3-2008: [GB/T 19651.3-2008] Miscellaneous lamp holders -- Part 2-2: Particular requirements -- Connectors for LED-modules Status: Valid
Basic dataStandard ID: GB 19651.3-2008 (GB19651.3-2008)Description (Translated English): [GB/T 19651.3-2008] Miscellaneous lamp holders -- Part 2-2: Particular requirements -- Connectors for LED-modules Sector / Industry: National Standard Classification of Chinese Standard: K74 Classification of International Standard: 29.140.10 Word Count Estimation: 8,826 Date of Issue: 2008-12-30 Date of Implementation: 2010-04-01 Quoted Standard: GB 19651.1-2008; GB/T 2423.10-2008; GB/T 2423.22-2002; IEC 60068-2-30-2005 Adopted Standard: IEC 60838-2-2-2006, IDT Regulation (derived from): Announcement of Newly Approved National Standards No. 27 of 2008 (total 140) Issuing agency(ies): General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China, Standardization Administration of the People's Republic of China Summary: This Chinese standard applies to miscellaneous internal connections (including LED module (module) is connected internally with connections), the connectors and LED-based module PCB (printed circuit board) together. GB 19651.3-2008: [GB/T 19651.3-2008] Miscellaneous lamp holders -- Part 2-2: Particular requirements -- Connectors for LED-modules---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order. Miscellaneous lampholders.Part 2-2. Particular requirements.Connectors for LED-modules ICS 29.140.10 K74 National Standards of People's Republic of China GB 19651.3-2008/IEC 60838-2-2.2006 Miscellaneous lampholders - Part 2-2. Particular requirements for LED module connector (IEC 60838-2-2.2006, IDT) Posted 2008-12-30 2010-04-01 implementation Administration of Quality Supervision, Inspection and Quarantine of People's Republic of China Standardization Administration of China released Table of ContentsIntroduction Ⅲ 1 Summary 1 2 Terms and definitions 1 3 General requirements 1 General Condition 4 Test 1 5 Standard Rating 1 6 Category 2 7 Flag 2 8 Protection against electric shock 2 9 Terminal 2 10 grounding device 2 11 Structure 2 12 Moisture resistance, insulation resistance and dielectric strength 2 13 Mechanical strength 2 14 Screws, current-carrying parts and connections 2 15 creepage distances and clearances 2 Durability 16 2 17 Heat and Fire 3 18 anti residual stresses (season cracking resistance) and corrosion resistance 3 19 anti-vibration performance 3 GB 19651.3-2008/IEC 60838-2-2.2006ForewordAll technical content in this section is mandatory. GB 19651 "Miscellaneous lampholders" is divided into three parts. --- Part 1. General requirements and tests; --- Part 2-1. Particular requirements for S14 lamp socket; The first part --- 2-2. LED module with special requirements connector. This is Part 2-2 GB 19651's. This section should be used with GB 19651.1-2008, it is appropriate in terms of GB 19651.1-2008 supplement or repair Formulated from the following changes. This section identical with IEC 60838-2-2.2006 "Miscellaneous lampholders Part 2-2. LED module connector special requirements" (English Chinese Version). For ease of use, this section made the following editorial changes. a) "IEC 60838-2-2 This part" be replaced by "GB 19651 of the present section"; b) Remove the IEC 60838-2-2 foreword; "." C) used in place of a decimal point as the decimal point, ""; d) For other international standard IEC 60838-2-2 has been cited as tantamount to the adoption of standard references used in this section of These national standards or industry standards instead of the corresponding international standards (see Part 2 of this chapter). This part is proposed by the China National Light Industry Council. This part of the National Electric lighting Standardization Technical Committee (SAC/TC224) centralized. This section drafted by. China Quality Certification Center, Beijing Institute of electric light source, Tongxiang Shenghui Lighting Appliance Co., Ltd., Shenzhen City Miao Ho hi-tech Development Co., Ltd., Shunde District of Foshan City, State Electric Co., Ltd., Zhongshan Xin Qi Wire Connector Factory. The main drafters of this section. Chen Song, Deng Yunfeng, together Xing Ping, Yang Xiaoping, Shen Jin Xiang, Li Mingyuan, and Huang Shi, Cai dry strength, Su Yong. This section first formulated. GB 19651.3-2008/IEC 60838-2-2.2006 Miscellaneous lampholders - Part 2-2. Particular requirements for LED module connector1 Summary1.1 Scope GB 19651 of this section applies to miscellaneous built-in connector (including LED module (module) internal connection connector), the connector Member-based LED module PCB (printed circuit board) used together. 1.2 Normative references The following documents contain provisions which, through reference in this Part of GB 19651, constitute provisions of this part. For dated reference documents Member, all subsequent amendments (not including errata content) or revisions do not apply to this section, however, encouraged to reach under this section Parties to research agreement to use the latest versions of these documents. For undated reference documents, the latest versions apply to this section. GB 19651.1-2008 determined in 1.2 and the following normative references apply to this section. GB/T 2423.10-2008 Environmental testing for electric and electronic products Part 2. Test methods Test Fc. Vibration (sinusoidal) (IEC 60068-2-6.1995, Environmentaltesting-Part 2. Tests-TestFc. Vibration (sinusoidal), IDT) GB/T 2423.22-2002 Environmental testing for electric and electronic products Part 2. Test methods - Test N. Temperature change (IEC 60068-2-14. 1984, Environmentaltesting-Part 2. Test-TestN. Changeoftemperature, IDT) GB 19651.1-2008 Miscellaneous lampholders - Part 1. General requirements and tests (IEC 60838-1.2004, IDT) IEC 60068-2-30.2005 Basic environmental testing procedures Part 2-30. Tests - Test Db and guidance. Damp heat, cyclic test (12 + 12h cycle)2 Terms and definitionsGB determined following terms and definitions 19651.1-2008 Chapter 2 apply to this section. 2.1 The solid-containing apparatus can be issued P-N junction by current excitation light radiation [GB/T 2900.65 in 845-04-40]. 2.2 A combined light source. In addition to the one or more light emitting diodes (LED), but may also include additional elements, such as optical, mechanical, electrical, and Electronic components (under consideration).3 General requirementsIn accordance with the requirements of GB 19651.1-2008 Chapter 3.4 General conditions for testsIn accordance with the requirements of GB 19651.1-2008 Chapter 4 and the following conditions apply. 16.1, 16.2 and 4.1 for the chapter 19 of each test shall be carried out on three other samples.5 Standard ratings5.1 The maximum rated voltage of AC 50V. Note. The equivalent maximum dc voltage 120V (under consideration). GB 19651.3-2008/IEC 60838-2-2.2006 5.2 Minimum rated current of 10mA, the maximum rated current of 3A. 5.3 rated operating temperature range. -30 ℃ ~ + 65 ℃. Unless the entire system is restricted to indoor use, otherwise the system should be consistent with a lower temperature. Related Precautions and see Symbol GB 7000.1-2007. NOTE. In the automotive industry, usually requires a minimum temperature of -40 ℃. Category 6 GB 19651.1-2008 accordance with the requirements of Chapter 5.7 logoIn accordance with Chapter 6 GB 19651.1-2008 requirements. NOTE. small size components may be required to reduce the height of the letters and symbols.8 Protection against electric shockIn accordance with the requirements of GB 19651.1-2008 Chapter 7.9 TerminalsGB 19651.1-2008 accordance with Chapter 8 requirements. 10 grounding device In accordance with the requirements of GB 19651.1-2008 Chapter 9. 11 Structure In accordance with the requirements of GB 19651.1-2008 Chapter 10 and the following conditions apply. 11.1 minimum cross-section of connecting wires to 0.22mm2. As the use of ribbon cable (sometimes referred to as flat cable), then the minimum cross-section Area should be 0.09mm2. It must be noted that the maximum cross-sectional area above the permitted current load should be considered given nominal 5.2 Flow range. 12 Moisture resistance, insulation resistance and dielectric strength GB 19651.1-2008 accordance with the requirements of Chapter 11. 13 Mechanical strength GB 19651.1-2008 accordance with the requirements of Chapter 12. 14 Screws, current-carrying parts and connections GB 19651.1-2008 accordance with the requirements of Chapter 13. 15 creepage distances and clearances GB 19651.1-2008 accordance with the requirements of Chapter 14. 16 Durability In accordance with the requirements of GB 19651.1-2008 Chapter 15 and the following conditions apply. 16.1 when the temperature is changing rapidly, the connector for the LED module should be able to maintain good electrical contact with the module. GB 19651.3-2008/IEC 60838-2-2.2006 Compliance is checked by the following test. IEC 60061 fitted with a cap (if any) of goods LED module or printed circuit board inserted into the connector, the connector contacts and Press the connection resistance measurement 16.3. Then connect the module and shall be subject to temperature change test GB/T 2423.22-2002 about Na tests described, the details as follows. Samples rated operating temperature range between the minimum and maximum of 100 cycles, exposure at each temperature of the two temperatures Time is 30min. During the test, the connector should not be used further change impacts, especially the impact of changes in contact. After the change of temperature tests, the connector is removed from the chamber, placed 12h. During this period, LED module remains inserted in the connector , And in this state, according to the requirements of 16.3 measured once again the connector contacts and connections resistance. 16.2 LED module connector in a high-humidity environment and the module should be able to maintain a good electrical contact. Compliance is checked by inspection and the following test. Complies with IEC 60061 (if any) of goods LED module or printed circuit board inserted into the connector, the connector contacts and electrical wiring By measuring the resistance of 16.3. And then connect the module should be accepted IEC 60068-2-30. damp heat cycle test of the 2005, the details are as follows. Samples should be at a maximum temperature of 55 ℃, 2 ℃ temperature change cycle 6 times. During the test, the connector should not be used further change impacts, especially the impact of changes in contact. After the heat cycle test, the connector is removed from the chamber, placed 12h. During this period, LED module remains inserted in the connector , And in this state, according to the requirements of 16.3 measured once again the connector contacts and connections resistance. 16.3 connector contacts and connections resistance measured as follows. Using the same connector rated current --- measure, on-time to be able to fully measure the resistance prevail; --- Leaded connector, and its resistance should be measured from the outlet 5mm lead at the connector between the two leads; --- No leads connected, you need to take a connector designed to use the smallest gauge wire. The resistance should be between the leads and pitch Lead 5mm at the outlet connector on the measure. Measurement voltage does not exceed 6V AC circuit. The measured resistance should not exceed the values obtained by the following formula. 0.045Ω + (A × shape) Wherein. when the state = 2, A = 0.01Ω When state > is 2, A = 0.015Ω And the number of independent points of contact PCB connector wherein like indicative of the measurement. 17 Heat and Fire GB 19651.1-2008 accordance with the requirements of Chapter 16. 18 anti residual stresses (season cracking resistance) and corrosion resistance In accordance with the requirements of GB 19651.1-2008 Chapter 17. 19 anti-vibration performance 19.1 LED module connector when subjected to vibration in normal use energy and modules to maintain good electrical contact. Compliance is checked by the following test. Complies with IEC 60061 (where applicable) goods LED module or PCB according to the manufacturer's instructions inserted into the connector and install. And then connect the module should be subject to vibration test GB/T 2423.10-2008 requirements, detailed steps are as follows. GB 19651.3-2008/IEC 60838-2-2.2006 Samples should be accepted 5 sweep cycles, the frequency range between 10Hz and 500Hz, each axis of the Length 2h, acceleration amplitude shall be 5g. During the test, change on the connecting member should not be further used, in particular the impact of changes related to the contact. After the vibration test, the test assembly was removed and check if the connector contacts and the inserted module is still good contact. GB 19651.3-2008/IEC 60838-2-2.2006 ......Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of GB 19651.3-2008_English be delivered?Answer: Upon your order, we will start to translate GB 19651.3-2008_English as soon as possible, and keep you informed of the progress. The lead time is typically 1 ~ 3 working days. The lengthier the document the longer the lead time.Question 2: Can I share the purchased PDF of GB 19651.3-2008_English with my colleagues?Answer: Yes. The purchased PDF of GB 19651.3-2008_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay. |
