Home Cart Quotation About-Us
www.ChineseStandard.net
SEARCH

GB 11562-2014 PDF English

US$145.00 · In stock · Download in 9 seconds
GB 11562-2014: Motor vehicles -- Forward visibility for drivers -- Requirements and measurement methods
Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure
Status: Valid

GB 11562: Historical versions

Standard IDUSDBUY PDFDeliveryStandard Title (Description)Status
GB 11562-2014145 Add to Cart Auto, 9 seconds. Motor vehicles -- Forward visibility for drivers -- Requirements and measurement methods Valid
GB 11562-1994185 Add to Cart Auto, 9 seconds. Motor vehicles-Forward visibility for drivers-Requirements and measurement methods Obsolete
GB 11562-1989RFQ ASK 3 days Passenger cars--Forward visibility for drivers Obsolete

Similar standards

GB 11566   GB 11567   GB/T 11563   GB 11555   

GB 11562-2014: Motor vehicles -- Forward visibility for drivers -- Requirements and measurement methods


---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GB11562-2014
GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 43.040.60 T 26 Replacing GB 11562-1994 Motor Vehicles forward Visibility for Drivers - Requirements and Measurement Methods Issued on: DECEMBER 31, 2014 Implemented on: JULY 1, 2015 Issued by. General Administration of Quality Supervision, Inspection and Quarantine; Standardization Administration of PRC.

Table of Contents

Foreword ... 3 1 Scope ... 6 2 Normative References ... 6 3 Terms and Definitions ... 6 4 Technical Requirements ... 12 5 Measuring Conditions ... 14 6 Determination Method of Driver’s Field of Vision ... 17 Appendix A (Informative) Comparison between Clause Numbers of this Standard and Clause Numbers of ECE R 125 ... 20 Appendix B (Normative) Determination Method of Dimensional Relationship between Primary Reference Marks of Vehicle and Three-Dimensional Coordinate System ... 23 Appendix C (Normative) Determination Procedures of Vehicle Riding Position H Point and Actual Seat-Back Angle ... 26

Foreword

The Clause 4, 5, 6 of this Standard are mandatory, while the rest are recommended. This Standard was drafted as per the rules specified in GB/T 1.1-2009. This Standard replaced GB 11562-1994 Motor Vehicles – Forward Visibility for Drivers – Requirements and Measurement Methods; the major differences between this Standard and GB 11562-1994 are as follows. a) Delete GB/T 11563 Motor Vehicles – Procedure for H-Point Determination, GB/T 11559 Motor Vehicles – Use in Defining their Seating Accommodation – Three- Dimensional H-Point Machine (these two standards are obsolete) from the normative references; b) Change the term of “three-dimensional coordinate system” in the original standard into “three-dimensional reference gird”; and add the following terms and definitions. --- Vehicle type with regard to the field of vision (see Sub-clause 3.1); --- Armoured vehicle (see Sub-clause 3.11); --- Extended seat-adjustment range (see Sub-clause 3.18); --- The angle of obstruction of the A pillar on the driver’s side (see Sub-clause 3.19); --- The angle of obstruction of the A pillar on the passenger side (see Sub-clause 3.20); --- Area “S” (see Sub-clause 3.21); --- Reference data (see Sub-clause 3.22); --- Three-dimensional H point machine (see Sub-clause 3.23); --- Torso-line (see Sub-clause 3.24); --- Center plane of occupant (see Sub-clause 3.25); --- Fiducial marks (see Sub-clause 3.26); --- Vehicle measuring attitude (see Sub-clause 3.27); c) Add the technical requirements for “armoured (bulletproof) vehicle” (see Sub- clause 4.2 of this Standard; Sub-clause 5.1.2 of ECE R125) d) Add the requirements for steering wheel adjustable vehicle (see Sub-clause 4.4.1 of this Standard; Sub-clause 5.1.3.1 of ECE R125) This Standard adopts the re-drafting method to modify and use the Economic Commission for Europe ECE R125 Rev.2/Add.124/Amend.3 (2011 Edition) Uniform Provisions Concerning the Approval of Motor Vehicles with regard to the Forward Field of Vision of the Motor Vehicle Driver. The comparison list between the clause numbers of this Standard and clause number of ECE R125 Regulation can refer to Appendix A of this Standard. The technical differences and causes between this Standard and ECE R 125 Regulation are as follows. --- Delete Sub-clause 1.2, 1.3 in Clause 1 of ECE R125 for the purpose of satisfying the rules of GB/T 1.1-2009, and meeting the requirements for motor vehicles driving on the right side of the road in China. --- Delete Clause 3 “Application for Certification”, Clause 4 “Certification”, Clause 7 “Changes and Expansion of Vehicle Types”, Clause 8 “Production Consistency”, Clause 9 “Punishment on Non-Production Consistency”, Clause 10 “Shut down”, Clause 11 “Addresses and Names of Testing Agencies and their Administrative Agencies”, information of manufacturer applying for certification in Annex 1, format of certification marks in Annex 2, etc. for the purpose of keeping consistent China’s motor vehicle management system, and for the benefit of the implementation and operation of this Standard. For the sake of usage, the following editorial changes are made against the ECE R125 Regulation. a) Change cm2 into mm2; b) Add informative appendix. This Standard was proposed by Ministry of Industry and Information Technology of the People’s Republic of China. This Standard shall be under the jurisdiction of National Technical Committee for Standardization of Automobiles (SAC/TC 114). Drafting organizations of this Standard. Dongfeng Motor Corporation, Natinoal Automobile Quality Supervision and Test Center (Xiangyang), China FAW Co., Ltd. R&D Center, China Quality Certification Center, European Automobile Manufacturers’ Association, Hubei Qixing Truck and Cabin Manufacturing Co., Ltd., and China National Accreditation Service for Conformity Assessment. Motor Vehicles forward Visibility for Drivers - Requirements and Measurement Methods

1 Scope

This Standard specifies the requirements and measurement methods of the direct visual filed within 180° range in front of the driver. This Standard is applicable to the Type-M1 automobile.

2 Normative References

The following documents are essential to the application of this document. For the dated documents, only the versions with the dates indicated are applicable to this document; for the undated documents, only the latest version (including all the amendments) are applicable to this document. GB 11555-2009 Motor Vehicles- Windshield Demisting and Defrosting Systems – Performance Requirements and Test Methods

3 Terms and Definitions

The following terms and definitions are applicable to this document. 3.1 Vehicle type with regard to the field of vision The vehicles with no difference in the following aspects. --- The external and internal shapes and arrangement that may influence the field of visions within 180° range in front of the driver; --- Shape, dimension and installation mode of front windshield glass. 3.2 Three-dimensional reference grid The coordinate system consisting of three orthogonal datum planes that is determined by the vehicle manufacturer at the initial design stage (see Figure B.1). These three datum planes are as follows. X datum plane --- vertical plane perpendicular to the Y datum plane; usually defined by passing the left and right front wheel center; Y datum plane – vehicle longitudinal symmetry plane; Z datum plane – the horizontal plane perpendicular to the Y and X datum planes. The three-dimensional coordinate system is used to determine the dimension relationship between the positions of design points on the drawing and the positions of these points on the vehicle. The coordinate value relevant to zero plane shall be determined on the basis of vehicle running state plus a front passenger [passenger mass is (75±1) kg]. If the vehicle is equipped with an adjustable clearance suspension away from the ground, it shall be tested in the state of normal use specified by the vehicle manufacturer. 3.3 Primary reference marks The holes on the vehicle body, surface, mark, identification symbols. The type of used reference marks and the positions of each mark on the X, Y, Z coordinates of the three- dimensional coordinate system, and on the relative design ground level shall be specified by the vehicle manufacturer. These reference marks can be used as the control points for the vehicle body assembly. 3.4 Seat-back angle The angle between the seat-back and the vertical line. 3.5 Actual seat-back angle The angle between the vertical line of H point and torso-line of three-dimensional H point machine when the seat is in the lowest and most rear positions within the normal range. The actual seat-back angle is theoretically equivalent to the designing seat- back angle. 3.6 Design seat-back angle The angle between the vertical line of R point and torso-line of three-dimensional H point machine on the seat-back position specified by the vehicle manufacturer. 3.7 V points In the passenger compartment, pass through the longitudinal vertical plane of the centerline position of front outside seat; it is relevant to the R point and design seat- back angle. Such point is used for checking whether the visual filed of vehicle meets the requirements. The normal range of the driver’s seat adjusted in the X-axis direction as specified by the vehicle manufacturer. 3.18 Extended seat-adjustment range The range of the seat adjusted upward in the X-axis direction beyond the normal range specified in Sub-clause 3.17, and also specified by the vehicle manufacturer; so that convert the seat into bed or facilitate to access to the vehicle. 3.19 The angle of obstruction of the A pillar on the driver’s side The angle between straight line passing through E2 point and paralleling to the tangent line of the outer edge of S2 section that passes through E1 point, and the tangent line of the inner edge of the S1 section that passes through E2 p... ......

Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al.
Image 1     Image 2     Image 3     

Tips & Frequently Asked Questions:

Question 1: How long will the true-PDF of English version of GB 11562-2014 be delivered?Answer: The full copy PDF of English version of GB 11562-2014 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.

Question 2: Can I share the purchased PDF of GB 11562-2014_English with my colleagues?Answer: Yes. The purchased PDF of GB 11562-2014_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.

Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countries

Question 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB 11562-2014 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.

Question 5: Should I purchase the latest version GB 11562-2014?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB 11562-2014 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically.

How to buy and download a true PDF of English version of GB 11562-2014?

A step-by-step guide to download PDF of GB 11562-2014_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).
Step 2: Search keyword "GB 11562-2014".
Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart.
Step 4: Select payment option (Via payment agents Stripe or PayPal).
Step 5: Customize Tax Invoice -- Fill up your email etc.
Step 6: Click "Checkout".
Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively.
Step 8: Optional -- Go to download PDF.
Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice.
See screenshots for above steps: Steps 1~3    Steps 4~6    Step 7    Step 8    Step 9