CQC-C0101-2014 English PDFUS$1639.00 · In stock
Delivery: <= 7 days. True-PDF full-copy in English will be manually translated and delivered via email. CQC-C0101-2014: China Compulsory Certification Implementation Detailed-Rules - Wire and cable products
Basic dataStandard ID: CQC-C0101-2014 (CQC C0101-2014; CQC-C01-01-2014; CQC-C0101-2014)Description (Translated English): China Compulsory Certification Implementation Detailed-Rules - Wire and cable products Sector / Industry: China Quality Certification Center - CCC Implementation Detailed-Rules Classification of Chinese Standard: CQC Word Count Estimation: 41,475 Date of Issue: 7/16/2014 Date of Implementation: 9/1/2014 Older Standard (superseded by this standard): CQC-01C-002-2007 Regulation (derived from): Notice No. 23 of the State Certification and Accreditation Administration, No. 23 of the State Certification and Accreditation Administration Issuing agency(ies): China Quality Certification Center Summary: This document specifies the China Compulsory Certification (CCC) implementation Detailed-Rules for Wire and cable products. This document defines the Wire and cable products's certification unit; certification entrusting; document requirements; sample req CQC-C0101-2014: China Compulsory Certification Implementation Detailed-Rules - Wire and cable products---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order. ID. CQC-C0101-2014 Mandatory product certification implementation rules Wire and cable products September 1, 2014 release September 1, 2014 implementation China Quality Certification Center Mandatory product certification implementation rules of wire and cable products CQC-C0101-2014 table of Contents0 .4 General requirements 0.1 Introduction .4 0.2 Terms and Definitions .4 0.2.1 the use of detection equipment manufacturers (referred TMP mode) 4 0.2.2 producers witnessed detection (abbreviated way WMT) .4 0.2.3 ODM (Original Design Manufacturer) production plant .4 0.2.4 ODM initial certificate holder ..4 0.2.5 product consistency verification tests ..5 0.3 Manufacturer classification principles .5 Authentication Mode Select 1 6 1.1 Basic authentication mode ..6 Refinement authentication mode 6 1.2 1.3 authentication mode applicability .7 2 Certification application unit 7 3 certification process and deadlines 8 3.1 Certification Scheme 8 3.2 Time frame for certification 8 4 certified pre-certification requirements .8 4.1 Certification commissioned 8 4.1.1 The proposed commission of the certification and acceptance of 8 4.1.2 Requirements for Certification information and related .9 4.2 Type testing 9 4.2.1 Type test program ..9 4.2.2 Requirements for sample 9 4.2.2.1 Sample selection principle of .9 4.2.2.2 Sample Number .10 4.2.2.3 Sampling/send the sample ..10 4.2.3 Test items and requirements ..10 Implementation ..10 4.2.4 type test 4.2.5 Type test report .11 4.3 factory inspection ..11 Define and factory inspection 4.3.1 factory inspection target coverage requirements .11 4.3.2 initial factory inspection .11 4.3.2.1 check the contents .11 4.3.2.2 Factory quality assurance ability examination ..11 4.3.2.3 Product consistency check .12 4.3.3 Initial factory inspection timing and inspection time 12 4.3.4 Inspection findings ..13 4.4 product consistency verification tests .13 4.5 Evaluation of certification results and approval .13 5 Follow-up inspection requirements .13 5.1 follow-up inspection program 14 Mandatory product certification implementation rules of wire and cable products CQC-C0101-2014 5.1.1-up inspection of the contents of 14 5.1.2 The frequency of follow-up inspection 14 5.1.3 Supervision after inspection man-days ..15 5.2 Follow-up audit trail requirements ..15 5.3 sampling test .15 5.3.1 sampling locations ..16 5.3.3 Sample test items and requirements .16 5.4 up inspection and approval of the results ..16 5.4.1 Evaluation of follow-up inspection .16 5.4.2 sampling test results of the evaluation ..17 5.4.3 Evaluation ..17 6 Certificate 17 6.1 validity of the certificate 17 Change 6.2 certificates ..17 6.3 Scope of Certification extended ..18 6.3.2 Adding authentication unit .18 6.4 certificate cancellation, suspension and revocation ..18 6.5 Use certificates ..18 7 certification mark 18 8 key raw materials .18 9 and charged according to claim 18 10 and the technical disputes, complaints and appeals related processes and deadlines 19 Annex 1 wire and cable products mandatory certification requirements for the type of sample .20 Annex 2 wire and cable products Compulsory Certification List of key raw materials .24 Annex 3 wire and cable products Compulsory Certification Product description 25 Annex 4 wire and cable products factories for compulsory certification of quality assurance capacity requirements ..27 Annex 5 wire and cable products factories for compulsory certification quality control testing requirements .33 Annex 6 to detect the use of company resources to implement detection (detection or witness) operating requirements 38 Mandatory product certification implementation rules of wire and cable products CQC-C0101-2014 0 General requirements 0.1 Introduction Wire and cable CCC implementation details (hereinafter referred to as the Regulations) is based on "compulsory production Product certification and implementation rules for wire and cable products "(CNCA-C01-01.2014) (hereinafter referred to as the Implementing Rules) of Requested the preparation, certification and implementation rules as a supporting document. In accordance with the Implementing Rules and China Quality Certification Center (in Under the requirements referred to CQC) quality manual, procedures, work instructions, etc., in the maintenance of the product identified Certificate validity, improve product quality, service certification and certification risk control principles, develop and publish this Certification rules. These Rules are based on the implementation of the rules require the preparation, use and implementation of common rules. Rules applicable Range of products, in accordance with the relevant provisions of certification and implementation of rules is consistent and in accordance with the Certification and Accreditation Supervisor Governor Management Committee (hereinafter referred to as CNCA) published catalog to define, implement directory adjustment announcement tune whole. CQC certification in accordance with the provisions of the implementation of the rules, the establishment of manufacturing enterprises category management requirements, combined with the production rate Industry classification, clear wire and cable compulsory product certification implementation requirements. 0.2 Terms and Definitions 0.2.1 the use of detection equipment manufacturers (referred TMP mode) Tests conducted by the designated testing organizations who use the company's equipment for testing, production enterprises to detect people Members assist, test reports issued by the designated testing organization. 0.2.2 producers witnessed detection (abbreviated way WMT) Experimental tests conducted by the company have used their equipment for testing, testing organization designated staff to detect Project and witnessed the testing conditions, test personnel, the company issued the original records, the drafting of the test report that Staff given testing organization review and confirm, the test report issued by the designated testing organization. 0.2.3 ODM (Original Design Manufacturer) production plant The ability to use the same quality assurance requirements, the same product design, production process control and inspection requirements, One or more producer (manufacturer) design, processing, producing the same products factory. 0.2.4 ODM initial certificate holder Mandatory product certification implementation rules of wire and cable products CQC-C0101-2014 ODM product for the first time to obtain tissue product certificates. 0.2.5 product consistency verification tests Product safety performance consistency of evaluation of manufactured and found to comply with relevant product standards, carried out product inspection. 0.3 Manufacturer classification principles CQC collect, collate and all kinds of certified products and their manufacturers quality-related information on the company Dynamic of category management. Principal certification, producers, production companies should cooperate. Producers divided into four categories, each with a Class A, Class B, Class C, Class D representation. Sort least package Include the following information. ① factory inspection (including the initial factory inspections and follow-up inspection Follow-up inspection) results; ② audit sampling test results (production site sampling or market sampling); ③ State pumping, pumping province, CCC and other special checks conclusion; ④ media exposure and consumer products, the public quality information feedback; ⑤ product certification testing capacity; ⑥ other information. CQC following categories based on the basic principles of the company are classified rating, and according to all kinds of information given Or irregular production of enterprises reclassifying grading, dynamic management. In principle, the company points Class results shall be in accordance with the order of the DCBA stepwise increase, the order ABCD stepwise or cross-level drop. Table 1 classification principles of the company Business category classification principles A Class Class B enterprises to provide relevant information, collected by the certification body of quality information and businesses to certification bodies Relevant information provided by a comprehensive risk assessment and determine the classification results assessed include at least The following aspects. a) factory inspection. initial factory inspection nearly two years, no follow-up inspection after inspection or verification site Not by the situation; b) product testing, inspection results. After nearly two years certified supervision and inspection found no non-conformities, national , Provincial quality supervision and inspection of all types and consistency verification test results were "qualified"; Mandatory product certification implementation rules of wire and cable products CQC-C0101-2014 c) by CQC detection capability of the company or with the national accreditation of Quality Supervision, Inspection and Quarantine Class AA Qualification Administration announcement. d) Other certified products and their manufacturers quality-related information. Class B In addition to Class A, Class C, other manufacturers like D. There is no quality information on the company, its Grading classification defaults to the class B. Class C Meets one of the following conditions. a) factory inspection judged to be "field-proven" (except for the standard version for the reason); b) the media exposure of the certified product quality problems and the Department of corporate responsibility, but does not involve suspended, revoked Certificates; c) CQC certified according to manufacturer and product-related quality information comprehensive evaluation concluded that the need to adjust For the class C. Class D Meets one of the following conditions. a) initial factory inspection, follow-up inspection after inspection conclusions determined as "no-go" of; b) Follow-up inspection test results for safety item failed; c) unjustified refusal inspection and/or sampling of; d) media exposure there is a big influence of the certified quality system and corporate responsibility; e) national, provincial and other types of product quality supervision and inspection results to be ineligible and unqualified projects Certified product quality serious impact; f) does not meet the other requirements of compulsory product certification has been suspended, revoked certificates; g) CQC certified according to manufacturer and product-related quality information comprehensive evaluation concluded that the need to adjust In Category D. NOTE. If changes to CQC public documents.1 Authentication mode selection1.1 Basic authentication mode Basic authentication mode. up inspection after type testing Refinement 1.2 authentication mode Mandatory product certification implementation rules of wire and cable products CQC-C0101-2014 According to the basic authentication mode, combined with production enterprise management principles, for different categories of enterprises in the certification Mode appropriate to increase the relevant certification elements, specific and detailed as follows. Mode 1. Type test certified oversight Mode 2. Type tests after initial factory inspection (consistency confirmation test) up inspection Mode 3. Type test (sample) after initial factory inspection up inspection Among them, the relevant requirements of follow-up inspection, see 5.1 "Follow-up inspection oversight program" requirement. 1.3 Applicability authentication mode Certified clients according to their own actual situation, see Table 2 authentication mode applicability of proposed recognition applies Permit application mode. Applicability Table 2 authentication mode Business category A type of application Initial application class applications from non-expanded expanded categories of applications It has been the use of the certificate ODM application Class A/Mode 1 Mode 1 Mode 1b Class B Mode 2 or Mode 3 Mode 2 or 3, 1, 2 or 3c mode 1 Class C/3 Mode 2 or Mode 2 or Mode 2 or 3 3 Class D/Mode 2 or Mode 3 Mode 2 or 3 2 or 3 a. "first application". the company is not obtained within the scope of Rule product CCC certification carried out the initial certification commission; "expanding class application". The company has obtained CCC certificate within the scope of Rule product certification commission carried out again, and the products have been certified products and subcategories small Different types; "non-expanding type application". the company has obtained within the scope of Rule product CCC certification and recertification carried out the commission, and the yield Subcategories and products have been certified Product Model same; "the use of ODM have been requesting the certificate". the use of ODM manufacturers to apply for the certificate has been carried out. b. exactly the same for the certified products with the original certified product, only the applicant or manufacturer to change the situation, the information provided could be considered a business Consistency verification, alternative type testing. c. For certified products, production processes and products have been certified to apply significant difference can not be overwritten, you should consider 2 or 3 mode. CQC certified products based on the principle of control and certification risk characteristics, combined with production enterprise management knot As a result, the client can determine the applicable certification authentication mode.2 Certification application unitAccordance with article 4 of the Implementing Rules. The same manufacturer (producer), different production companies (sites) products should be in different application Mandatory product certification implementation rules of wire and cable products CQC-C0101-2014 Unit; the same company (site), different manufacturers (producers) products shall be in different Application unit.3 certification process and deadlines3.1 Certification Process Certification process include. certification commission, accepting and data evaluation, initial type testing and factory inspection, to close Costs, evaluation of certification results and approval of certification decision making and follow-up inspection and other links. 3.2 Time frame for certification Date of acceptance certification commission till the issuance date of the certificate of no more than 90 days (long detection period production Exclusion product), including type testing, initial factory inspection and post-inspection report time period (applicable ), The evaluation of certification results and approval of certificates. More time to complete certification activities, excluding the rectification does not meet the time, detection time and retest consistency Confirm the test of time. The situation does not meet the requirements for certification, CQC/laboratory should inform the client in an effective manner People, and explain the reasons. The rules did not make the certification process and clearly defined time limit in order to CQC relevant program files and operating means Guide book requirements will prevail .CQC accordance with the relevant procedures and work instructions document control requirements of the time limit to complete the certification Related work, certification clients, producers, production companies should cooperate. Authentication client, the producer (manufacturer), the manufacturer certification implementation should be actively cooperate and Help. Since the authentication client, producers, manufacturers its own reasons to complete certification activities leading to overdue Authentication timeout, not counted in the time frame for certification. 4 certified pre-certification requirements 4.1 Certification commission 4.1.1 certification commission proposed and accepted When care is required to provide the necessary corporate information and product information, including business registration certificate, organization code and Product descriptions .CQC according to the relevant requirements of the application for review promptly issued admissible or inadmissible through Mandatory product certification implementation rules of wire and cable products CQC-C0101-2014 Know, or ask the client to re-apply for accreditation certification after rectification. 4.1.2 Requirements for Certification information and related Certification principal shall, after receiving the required application to CQC certification scheme and/or provide information about laboratory Application information and technical materials typically include. (1) a formal application; (2) description of wire and cable products; (3) factory inspection questionnaire; (4) certified client, the producer (manufacturer), the company registration documents; (5) key raw materials producers (manufacturers) and/or the company quality certificate (if any); (6) other information (such as. quality management system certification documents, a trademark of supporting documents, etc.); (7) The authentication client, the producer (manufacturer), signed a related agreement between manufacturers or contract, ODM such agreement, power of attorney and a copy of the original certificate (if required) and the like; (8) For the application, and documents related to the change project. Business name, address and other data or information to declare laws and regulations compliance, responsible for the authenticity and commitment Bear the corresponding responsibility. 4.2 Type tests 4.2.1 Type test program The need for type test certification commission, after passing the examination application data, CQC should develop Type Protocol, and notifies the client authentication type testing program including sample requirements and quantities, and testing standards Project, laboratory information. 4.2.2 Sample Requirements 4.2.2.1 Sample selection principle of CQC in accordance with the implementation of the rules set forth in Annex unit division, according to the Rules for the Implementation of Annex 1 to send samples Requirements and principles set sampling unit or combination unit/send samples of the sample requirements. Products when applying for certification, samples shall products selected representative model specifications, And selected samples should cover the safety requirements of products, structural requirements and key raw material manufacturers. Mandatory product certification implementation rules of wire and cable products CQC-C0101-2014 4.2.2.2 Number of Samples General wire and cable products, Quantity of 50m. Each core conductor cross section ≥50mm2 plastic insulation products, each core conductor cross-section of the insulating rubber production ≥16mm2 Goods, Quantity of ≥30m. 4.2.2.3 Sampling/send the sample Under normal circumstances, the principal certification program required type test and sample preparation to designated experiments Chamber test specimens shall be entrusted to a certified company according to the normal way of processing products, certification commission Shall ensure that the sample provided by the actual production of its products consistent .CQC and/or laboratory response authentication delegation Authenticity provided samples for review. Doubt the authenticity of the laborator......Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of CQC-C0101-2014_English be delivered?Answer: Upon your order, we will start to translate CQC-C0101-2014_English as soon as possible, and keep you informed of the progress. The lead time is typically 4 ~ 7 working days. The lengthier the document the longer the lead time.Question 2: Can I share the purchased PDF of CQC-C0101-2014_English with my colleagues?Answer: Yes. The purchased PDF of CQC-C0101-2014_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay. |
