CJ/T 536-2019 PDF EnglishUS$349.00 · In stock · Download in 9 seconds
CJ/T 536-2019: Adjustable weir-gate Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid
Similar standardsCJ/T 536-2019: Adjustable weir-gate---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/CJT536-2019Adjustable weir-gate ICS 13.060.30 P41 People's Republic of China urban construction industry standards Replace CJ/T 3029-1994 Adjustable trick Published on.2019-03-04 2019-09-01 implementation Ministry of Housing and Urban-Rural Development Content Foreword III 1 Scope 1 2 Normative references 1 3 Terms and Definitions 2 4 Basic form and model 2 5 General requirements 3 6 Material 3 7 requirement 4 8 Test method 7 9 Inspection rules 9 10 Marking, packaging, transport and storage 10 Appendix A (informative) Adjustable structure basic structure type 11 ForewordThis standard was drafted in accordance with the rules given in GB/T 1.1-2009. This standard is a revision of CJ/T 3029-1994 "Adjustable Tricks (hole width 300~5000mm)", the date of implementation of this standard Since then, CJ/T 3029-1994 has been abolished. The main technical changes in this standard compared with CJ/T 3029-1994 are as follows. --- Added terms and definitions (see 3.1, 3.2, 3.3); --- Increased the requirements for the operation mode, sealing method and transmission mode, and increased the requirements for the model representation method (see 4.1, 4.2); ---Modified the maximum forward and reverse design pressure values of adjustable slamming doors (see Table 1 of 5.2,.1994 edition); --- Revised the materials of the main components of the adjustable slamming door (see Table 2, Table 3 of the.1994 edition); --- Increased material requirements for hard and soft seals (see 6.3); --- Added technical requirements for rotary adjustable tricks (see 7.2.1.2, 7.2.1.3, 7.5.5); --- Increased gasket requirements in grease environments (see 7.2.1.4); ---Modified part of the door frame and door panel requirements (see 7.2.1 and 7.2.2,.1994 editions 4.3.1 and 4.3.2); ---Modified the requirements for the contact surface between the guide rail and the door frame (see 7.2.3.1, 4.3.3.2 of the.1994 edition); --- Increased the requirements for locking devices (see 7.2.4); --- Increased the requirements for lifting lugs, screw and connecting parts, screw guides (see 7.2.5, 7.2.6, 7.2.7); --- Increased the requirements of the hoist rated output torque, rated power, handwheel, handle and opening position indicator (see 7.2.8.3, 7.2.8.4, 7.2.8.5); --- Increased the total thickness of the paint film in the environment containing chloride ions (see 7.4.4); --- Increased the requirements for soft seal compression (see 7.5.2); --- Revised the requirements for the level of adjustment of the adjustable jaw (see 7.5.4, 4.3.7.1 of the.1994 edition); --- Increased leakage requirements for adjustable slamming doors under different conditions (see 7.5.8, 5.3 of.1994). This standard was proposed by the Institute of Standardization of the Ministry of Housing and Urban-Rural Development. This standard is under the jurisdiction of the Municipal Water Supply and Drainage Standardization Technical Committee of the Ministry of Housing and Urban-Rural Development. This standard was drafted. Tianjin Municipal Engineering Design and Research Institute, Tianjin Aijie Environmental Technology Engineering Co., Ltd., Jiangsu Tianyu Environmental Protection Set Group Co., Ltd. The main drafters of this standard. Wang Xiuduo, Zhao Lejun, Wei Xinqing, Zhang Yunxia, Zhao Junjian, Lu Douhong. The previous versions of the standards replaced by this standard are. ---CJ/T 3029-1994. Adjustable trick1 ScopeThis standard specifies the basic form and model of the adjustable door, general requirements, materials, requirements, test methods, inspection rules, signs, packages. Loading, transport and storage. This standard applies to the manufacture and inspection of adjustable shackles used in water supply and drainage engineering.2 Normative referencesThe following documents are indispensable for the application of this document. For dated references, only dated versions apply to this article. Pieces. For undated references, the latest edition (including all amendments) applies to this document. GB/T 191 packaging storage and transportation icon GB/T 700 carbon structural steel GB/T 985.1 Recommended groove for gas welding, electrode arc welding, gas shielded welding and high energy beam welding GB/T 985.2 recommended groove for submerged arc welding GB/T 985.3 Recommended groove for aluminum and aluminum alloy gas shielded welding GB/T 1176 cast copper and copper alloy GB/T 1184 Shape and position tolerances without tolerance values GB/T 1220 stainless steel rod GB/T 1348 ductile iron castings GB/T 2828.1. Sampling procedures for sampling by sampling - Part 1 . Batch-to-batch sampling plan, searched by AQL GB/T 3280 stainless steel cold rolled steel plate and strip GB/T 3797 electrical control equipment GB/T 4237 stainless steel hot rolled steel sheet and strip GB/T 4622.1 Wound gasket classification GB/T 4622.2 Wound gasket gasket flange size GB/T 4622.3 winding gasket technical conditions GB/T 4942.1-2006 The degree of protection (IP code) of the overall structure of a rotating electrical machine GB/T 5796.4-2005 Trapezoidal threads - Part 4. Tolerance GB/T 6388 transport packaging receipt and delivery mark GB/T 6414 casting dimensional tolerances, geometric tolerances and machining allowances GB/T 8923.1-2011 - Determination of surface cleanliness of steels - Part 1 . Uncoated Corrosion grade and treatment grade of the surface of the steel and the surface of the steel after the original coating is completely removed GB/T 10095.1 Precision of cylindrical gears - Part 1. Definitions and permissible values GB/T 10095.2 Precision of cylindrical gears - Part 2. Definitions and permissible values of radial integrated deviation and radial runout GB/T 11365-1989 Bevel gear and hypoid gear precision GB/T 13306 signage General technical conditions for GB/T 13384 mechanical and electrical product packaging GB/T 14647 chloroprene rubber CR121, CR122 CJ/T 536-2019 Adjustable weir-gate ICS 13.060.30 P41 People's Republic of China urban construction industry standards Replace CJ/T 3029-1994 Adjustable trick Published on.2019-03-04 2019-09-01 implementation Ministry of Housing and Urban-Rural Development Content Foreword III 1 Scope 1 2 Normative references 1 3 Terms and Definitions 2 4 Basic form and model 2 5 General requirements 3 6 Material 3 7 requirement 4 8 Test method 7 9 Inspection rules 9 10 Marking, packaging, transport and storage 10 Appendix A (informative) Adjustable structure basic structure type 11ForewordThis standard was drafted in accordance with the rules given in GB/T 1.1-2009. This standard is a revision of CJ/T 3029-1994 "Adjustable Tricks (hole width 300~5000mm)", the date of implementation of this standard Since then, CJ/T 3029-1994 has been abolished. The main technical changes in this standard compared with CJ/T 3029-1994 are as follows. --- Added terms and definitions (see 3.1, 3.2, 3.3); --- Increased the requirements for the operation mode, sealing method and transmission mode, and increased the requirements for the model representation method (see 4.1, 4.2); ---Modified the maximum forward and reverse design pressure values of adjustable slamming doors (see Table 1 of 5.2,.1994 edition); --- Revised the materials of the main components of the adjustable slamming door (see Table 2, Table 3 of the.1994 edition); --- Increased material requirements for hard and soft seals (see 6.3); --- Added technical requirements for rotary adjustable tricks (see 7.2.1.2, 7.2.1.3, 7.5.5); --- Increased gasket requirements in grease environments (see 7.2.1.4); ---Modified part of the door frame and door panel requirements (see 7.2.1 and 7.2.2,.1994 editions 4.3.1 and 4.3.2); ---Modified the requirements for the contact surface between the guide rail and the door frame (see 7.2.3.1, 4.3.3.2 of the.1994 edition); --- Increased the requirements for locking devices (see 7.2.4); --- Increased the requirements for lifting lugs, screw and connecting parts, screw guides (see 7.2.5, 7.2.6, 7.2.7); --- Increased the requirements of the hoist rated output torque, rated power, handwheel, handle and opening position indicator (see 7.2.8.3, 7.2.8.4, 7.2.8.5); --- Increased the total thickness of the paint film in the environment containing chloride ions (see 7.4.4); --- Increased the requirements for soft seal compression (see 7.5.2); --- Revised the requirements for the level of adjustment of the adjustable jaw (see 7.5.4, 4.3.7.1 of the.1994 edition); --- Increased leakage requirements for adjustable slamming doors under different conditions (see 7.5.8, 5.3 of.1994). This standard was proposed by the Institute of Standardization of the Ministry of Housing and Urban-Rural Development. This standard is under the jurisdiction of the Municipal Water Supply and Drainage Standardization Technical Committee of the Ministry of Housing and Urban-Rural Development. This standard was drafted. Tianjin Municipal Engineering Design and Research Institute, Tianjin Aijie Environmental Technology Engineering Co., Ltd., Jiangsu Tianyu Environmental Protection Set Group Co., Ltd. The main drafters of this standard. Wang Xiuduo, Zhao Lejun, Wei Xinqing, Zhang Yunxia, Zhao Junjian, Lu Douhong. The previous versions of the standards replaced by this standard are. ---CJ/T 3029-1994. Adjustable trick1 ScopeThis standard specifies the basic form and model of the adjustable door, general requirements, materials, requirements, test methods, inspection rules, signs, packages. Loading, transport and storage. This standard applies to the manufacture and inspection of adjustable shackles used in water supply and drainage engineering.2 Normative referencesThe following documents are indispensable for the application of this document. For dated references, only dated versions apply to this article. Pieces. For undated references, the latest edition (including all amendments) applies to this document. GB/T 191 packaging storage and transportation icon GB/T 700 carbon structural steel GB/T 985.1 Recommended groove for gas welding, electrode arc welding, gas shielded welding and high energy beam welding GB/T 985.2 recommended groove for submerged arc welding GB/T 985.3 Recommended groove for aluminum and aluminum alloy gas shielded welding GB/T 1176 cast copper and copper alloy GB/T 1184 Shape and position tolerances without tolerance values GB/T 1220 stainless steel rod GB/T 1348 ductile iron castings GB/T 2828.1. Sampling procedures for sampling by sampling - Part 1 . Batch-to-batch sampling plan, searched by AQL GB/T 3280 stainless steel cold rolled steel plate and strip GB/T 3797 electrical control equipment GB/T 4237 stainless steel hot rolled steel sheet and strip GB/T 4622.1 Wound gasket classification GB/T 4622.2 Wound gasket gasket flange size GB/T 4622.3 winding gasket technical conditions GB/T 4942.1-2006 The degree of protection (IP code) of the overall structure of a rotating electrical machine GB/T 5796.4-2005 Trapezoidal threads - Part 4. Tolerance GB/T 6388 transport packaging receipt and delivery mark GB/T 6414 casting dimensional tolerances, geometric tolerances and machining allowances GB/T 8923.1-2011 - Determination of surface cleanliness of steels - Part 1 . Uncoated Corrosion grade and treatment grade of the surface of the steel and the surface of the steel after the original coating is completely removed GB/T 10095.1 Precision of cylindrical gears - Part 1. Definitions and permissible values GB/T 10095.2 Precision of cylindrical gears - Part 2. Definitions and permissible values of radial integrated deviation and radial runout GB/T 11365-1989 Bevel gear and hypoid gear precision GB/T 13306 signage General technical conditions for GB/T 13384 mechanical and electrical product packaging GB/T 14647 chloroprene rubber CR121, CR122 ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of CJ/T 536-2019 be delivered?Answer: The full copy PDF of English version of CJ/T 536-2019 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of CJ/T 536-2019_English with my colleagues?Answer: Yes. The purchased PDF of CJ/T 536-2019_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- CJ/T 536-2019 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.How to buy and download a true PDF of English version of CJ/T 536-2019?A step-by-step guide to download PDF of CJ/T 536-2019_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "CJ/T 536-2019". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
