GB/T 42825-2023 PDF EnglishUS$480.00 · In stock · Download in 9 seconds
GB/T 42825-2023: General technical specification for electric scooters Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid
Similar standardsGB/T 42825-2023: General technical specification for electric scooters---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT42825-2023GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 43.140 CCS Y 14 General Technical Specification for Electric Scooters Issued on. AUGUST 6, 2023 Implemented on. AUGUST 6, 2023 Issued by. State Administration for Market Regulation; Standardization Administration of the People’s Republic of China. Table of ContentsForeword... 3 1 Scope... 4 2 Normative References... 4 3 Terms and Definitions... 5 4 General Requirements... 6 5 Requirements... 6 5.1 Structure... 6 5.2 Performance... 7 5.3 Electrical safety... 8 5.4 Mechanical safety... 9 5.5 Components... 10 5.6 Environmental adaptability... 12 5.7 Instructions... 12 6 Test Method... 13 6.1 Structural inspection... 13 6.2 Performance test... 14 6.3 Electrical safety testing... 17 6.4 Mechanical safety test... 19 6.5 Component test... 23 6.6 Environmental adaptability test... 24 6.7 Instruction manual... 26 6.8 Test conditions... 26 6.9 Instrument accuracy... 26 7 Inspection Rules... 26 7.1 General... 26 7.2 Exit-factory inspection... 26 7.3 Periodic inspection... 27 7.4 Type inspection... 29 8 Marking, Packaging, Transportation and Storage... 29 8.1 Marking... 29 8.2 Packaging... 31 8.3 Transportation... 31 8.4 Storage... 311 ScopeThis Document specifies the structure, performance, electrical safety, mechanical safety, components, environmental adaptability, inspection rules and marking, instructions, packaging, transportation and storage requirements of electric scooters; describes the corresponding test methods; and defines the corresponding terms and definitions. This Document applies to the design, manufacture and sales of electric scooters. This Document does not apply to children's electric scooters and competitive/sports electric scooters.2 Normative ReferencesThe provisions in following documents become the essential provisions of this Document through reference in this Document. For the dated documents, only the versions with the dates indicated are applicable to this Document; for the undated documents, only the latest version (including all the amendments) is applicable to this Document. GB/T 2423.1 Environmental testing - Part 2.Test methods - Tests A. Cold GB/T 2423.3 Environmental testing - Part 2.Testing method - Test Cab. Damp heat, steady state GB/T 2828.1 Sampling procedures for inspection by attribute - Part1.Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection GB/T 2829 Sampling procedures and tables for periodic inspection by attributes (apply to inspection of stability for productive process) GB/T 4208 Degrees of protection provided by enclosure (IP code)3 Terms and DefinitionsFor the purposes of this Document, the following terms and definitions apply. 3.1 Electric scooter The vehicle that is composed of handlebars (crossbars, stems), wheels, pedals, etc., powered by batteries, driven by DC motors, and can slide on the ground at low speed.4 General Requirements4.1 Electric scooters shall not be dangerous in normal use, under reasonably foreseeable misuse and malfunctions. Dangers include but are not limited to the following situations. 4.2 The safety of lithium-ion batteries (hereinafter referred to as "batteries") shall comply with the provisions of GB/T 40559; and the initial capacity, high temperature capacity, and low temperature capacity of the batteries shall comply with the provisions of SJ/T 11685.Batteries that have been used in cascades should not be used. 4.3 The safety of the charger shall comply with the provisions of GB 4706.18 and shall be compatible with the battery system of the electric scooter; 4.4 The combustion classification of the circuit board and the non-metallic shell of battery shall be no lower than the Level-V-1 in GB/T 5169.16.5 Requirements5.1 Structure 5.1.1 Sharp edges During normal riding, handling and maintenance, there shall be no exposed sharp edges on the rider's hands, legs and other parts of the body that may be touched. 5.1.4 Internal wiring Internal wiring shall meet the following requirements. 5.2 Performance 5.2.1 General The maximum speed and motor start of the electric scooter shall meet the requirements of 5.2.2 and 5.2.3, respectively; the braking performance shall meet the requirements of 5.2.4.1 and shall also meet one of the requirements of 5.2.4.2 or 5.2.4.3. 5.2.4.2 Mean fully developed deceleration When all braking systems are used, the mean fully developed deceleration shall be ≥3.4m/s2; when only the mechanical braking system is used, the mean fully developed deceleration shall be ≥2.5m/s2. 5.3 Electrical safety 5.3.1 Maximum output voltage The maximum output voltage of the battery shall be less than or equal to 60V. 5.3.2 Short circuit protection The charging circuit and battery output circuit of the electric scooter shall be equipped with protective devices such as fuses. 5.3.5 Charging lock During the battery charging process, the electric scooter's motor shall not run. 5.3.6 Braking power-off The electric scooter shall have a braking power-off function. When the electric scooter is braked, the motor input current shall be less than or equal to the current when it has no torque output (standby current) within 3s. 5.3.7 Charging port protection The charging port of the electric scooter shall have protection design functions against reverse connection and electric shock. 5.4 Mechanical safety 5.5 Components 5.5.1 Folding locking device The requirements for the folding locking device are as follows. 5.5.2 Telescopic mechanism The telescopic mechanism shall meet the following requirements. 5.5.3 Pedal The anti-slip area of the pedal of the electric scooter shall be no less than 150cm2. 5.5.4 Battery The electric scooter shall be driven by the original battery. The original battery refers to the battery that can be produced by other manufacturers with the authorization or permission of the original manufacturer of the electric scooter.6 Test Method6.1 Structural inspection 6.1.1 Sharp edges Use visual inspection and finger touch to check whether the rider's body can touch the electric scooter. 6.1.3 Active clearance Use a go gauge to measure the active clearance of the electric scooter. 6.1.4 Internal wiring Use visual methods to check the internal wiring of the electric scooter. 6.2 Performance test 6.2.1 Performance test conditions 6.2.1.4 Test vehicle The test vehicle is a fully assembled electric scooter; and the battery is fully charged according to the method described by the manufacturer, The battery capacity during the test is no less than 90% of its rated capacity. 6.2.2 Maximum speed The driver (6.2.1.3) drives the test vehicle to accelerate from rest, keeping the speed knob at the maximum opening, so that the driving speed reaches the maximum speed and remains unchanged; passes through the 5m test section; and records the speed value of the test section. The test is repeated twice and the average value is taken. 6.2.4 Braking performance 6.2.4.1 Braking structure The braking system of the test vehicle is visually inspected. 6.3.2 Short circuit protection Check whether the battery charging circuit and battery output circuit of the test vehicle are equipped with protective devices such as fuses according to the circuit diagram. Check the charging circuit, battery output circuit, or circuit board, if necessary. 6.3.5 Charging lock Use the adapter charger to charge the test vehicle battery when it is powered off. During the battery charging process, turn on the power switch and check the operation of the motor of the test vehicle. 6.3.6 Braking power off Lift the driving wheel of the test vehicle off the ground; connect a DC ammeter in series to the battery output terminal; turn on the power; and record the current value (standby current) when there is no torque output on the driving wheel. 6.3.7 Charging port protection Check whether the charging port of the test vehicle and the charger output interface are the only connection methods; if not, try to reversely connect the charger to the charging port of the test vehicle to check whether the reverse connection protection is effective. 6.4 Mechanical safety test 6.4.1 Pedal static strength Apply 3 times the maximum load (G) specified by the manufacturer to the center of the pedal through a support with a cross-sectional size of 150mm×150mm, as shown in Figure 2; and maintain for 5 min. 6.4.2 Entire vehicle load drop Apply and fix the maximum load (G) specified by the manufacturer on the pedal of the test vehicle. Fix the rear wheel and raise the front wheel. When the front wheel is 200mm above the test surface, drop it onto a concrete or similar hardness flat surface, as shown in Figure 3. Repeat the drop for 3 times. 6.4.3 Pull-off force The pull-off force test is carried out in the following manner. 6.4.4 Static load strength of handlebar The handlebar strength test is carried out in the following manner.7 Inspection Rules7.1 General The product shall be inspected and qualified by the quality inspection department of the manufacturer and shall be shipped only after being accompanied by a certificate of conformity. Product inspection is divided into exit-factory inspection and type inspection. 7.2 Exit-factory inspection 7.2.3 Batch quality The quality level of the inspection batch is expressed as the percentage of disqualified products. 7.2.4 Others When the inspection batch is used for delivery acceptance by both the supplier and the purchaser, the requirements specified in 7.2 may be agreed upon in the contract. 7.3 Periodic inspection 7.4.2 Inspection samples and inspection sequence Inspect according to all items in Clause 5.First, all the samples are inspected according to the exit-factory inspection items. After passing the exit-factory inspection, they are inspected in combination with the test groups, inspection items and inspection sequence specified in the periodic inspection.8 Marking, Packaging, Transportation and Storage8.1 Marking 8.1.1 Product marking The product marking of the electric scooter shall contain the necessary information to inform the user and its specification parameters, at least the following information. 8.1.2 Safety warning signs The electric scooter body shall have necessary safety warning signs to inform users of safe use. If necessary, safety warning signs for preventive measures when using, operating and maintaining electric scooters shall be provided. Safety warning signs include but are not limited to. 8.1.3 Packaging mark The outer packaging of the product shall have the following marks. 8.2 Packaging 8.2.1 Products shipped from the factory shall be accompanied by product certificates, packing lists, and product description materials. 8.2.2 External cartons or other packaging boxes shall be tied firmly. In special cases, it can be determined according to the requirements of the purchaser (contract). 8.4 Storage ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 42825-2023 be delivered?Answer: The full copy PDF of English version of GB/T 42825-2023 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 42825-2023_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 42825-2023_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 42825-2023 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.How to buy and download a true PDF of English version of GB/T 42825-2023?A step-by-step guide to download PDF of GB/T 42825-2023_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 42825-2023". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
