YY/T 0286.4-2020 PDF EnglishUS$260.00 · In stock · Download in 9 seconds
YY/T 0286.4-2020: Special infusion sets - Part 4: Infusion sets for single use with pressure infusion apparatus Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid YY/T 0286.4: Historical versions
Similar standardsYY/T 0286.4-2020: Special infusion sets - Part 4: Infusion sets for single use with pressure infusion apparatus---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/YYT0286.4-2020 YY PHARMACEUTICAL INDUSTRY STANDARD ICS 11.040.20 C 31 Replacing YY 0286.4-2006 Special infusion sets - Part 4.Infusion sets for single use with pressure infusion apparatus (ISO 8536-8.2015, Infusion equipment for medical use - Part 8.Infusion sets for single use with pressure infusion apparatus, MOD) Issued on. JUNE 30, 2020 Implemented on. JUNE 01, 2021 Issued by. National Medical Products Administration Table of ContentsForeword... 3 Introduction... 5 1 Scope... 6 2 Normative references... 6 3 Terms and definitions... 6 4 General requirements... 7 5 Materials... 11 6 Physical requirements... 11 7 Chemical requirements... 13 8 Biological requirements... 13 9 Packaging... 13 10 Labels... 13 11 Disposal... 14 Appendix A (Normative) Physical test... 16 Appendix B (Normative) Storage volume... 17 Appendix C (Informative) Technical differences between this Part and ISO 8536- 8.2015 and reasons... 20 References... 22ForewordThe “Special infusion sets” standard series is composed of the following parts. - YY 0286.1 Special infusion sets - Part 1.Infusion sets with precision filters for single use - YY 0286.2 Fluid lines for use with pressure infusion equipment and accessories for single use - Part 1.Fluid lines - YY 0286.3 Special infusion sets - Part 3.Light-resistant infusion sets for single use - YY/T 0286.4 Special infusion sets - Part 4.Infusion sets for single use with pressure infusion apparatus - YY/T 0286.5 Special infusion sets - Part 5.Bottle-type and bag-type infusion sets for single use - YY/T 0286.6 Special infusion sets - Part 6.Infusion sets for single use with graduated flow regulator This Part is Part 4 of YY/T 0286. This Part was drafted in accordance with the rules given in GB/T 1.1-2009. This Part replaces YY/T 0286.4-2006.Compared with YY/T 0286.4-2006, the main changes in this Part are as follows. - CHANGE the nature of the standard, from mandatory to recommended; - MODIFY the degree of standard adoption, "IDT" (identical adoption) to "MOD" (modified adoption); - UPDATE the normative references (see Chapter 2; Chapter 2 of the 2006 edition); - ADD Chapter 3 Terms and definitions (see Chapter 3); - DELETE the original Chapter 4 Marking (Chapter 4 of the 2006 edition); - MODIFY the pipeline requirements, which identically adopt the pipeline length requirements of ISO 8536-8 (see 6.11; 6.11 of the 2006 edition); - MODIFY the storage volume requirements; ADD the Appendix B. Test method for storage volume (see 6.14; 6.14 of the 2006 edition); - MODIFY the Chapter 10 Requirements for labeling (see Chapter 10; Chapter 10 of the 2006 edition); - ADD the Chapter 11 Disposal requirements (see Chapter 11); - DELETE the test method A.4 of the original Appendix A (see A.4 of the 2006 edition); - MODIFY A.3 Leakage test method (see A.3; A.3 of the 2006 edition). - UPDATE references. This Part uses the redrafting method, to modifies and adopts ISO 8536-8.2015 "Infusion equipment for medical use - Part 8.Infusion sets for single use with pressure infusion apparatus". There are technical differences between this Part and ISO 8536-8.2015.Appendix C is added after Appendix A and Appendix B, giving a list of corresponding technical differences and their causes. This Part has also made the following editorial changes. - ADD the informative Appendix C, giving a list of the corresponding technical differences and their reasons compared with ISO 8536-8.2015. Please note that some content in this document may be subject to patents. The publisher of this document assumes no responsibility for identifying these patents. This Part was proposed by the National Medical Products Administration. This Part shall be under the jurisdiction of the National Medical Infusion Equipment Standardization Technical Committee (SAC/TC 106). Drafting organizations of this Part. Shandong Provincial Medical Device Product Quality Inspection Center, Terumo Medical Products (Hangzhou) Co., Ltd., Wuhan Zhixun Chuangyuan Technology Development Co., Ltd., Jiangsu Yakai Medical Technology Co., Ltd., Shandong Xinhua Ande Medical Supplies Ltd. The main drafters of this Part. Yao Xiujun, Wu Liqun, Liu Weijun, Wu Qiyu, Zhang Xianshun, Li Kanyuan. This standard replaces the standard previously issued as follows. - YY 0286.4-2006.1 ScopeThis Part of the "Specialized infusion sets" series of standards specifies the requirements for sterile supplied disposable infusion sets (hereinafter referred to as "infusion sets"), for infusion equipment which has a pressure of 200 kPa and below. This Part applies to disposable infusion sets of infusion equipment, which has a pressure of 200 kPa and below.2 Normative referencesThe following documents are essential to the application of this document. For the dated documents, only the versions with the dates indicated are applicable to this document; for the undated documents, only the latest version (including all the amendments) is applicable to this standard.3 Terms and definitionsThe following terms and definitions apply to this document. The volume of the pipeline under pressure, which is the sum of the filling volume (VF) and the bolus volume (VB).4 General requirementsThe infusion set shall have a protective sheath, to keep the inside of the infusion set sterile before use. The cork piercer or needle of the gas inlet device shall have a protective sheath.5 MaterialsThe materials, which are used in manufacturing the infusion set and its components given in Chapter 4, shall meet the requirements of Chapter 6.The materials of the components of the infusion set, that are in contact with the solution, shall also comply with the requirements specified in Chapters 7 and 8.6 Physical requirementsWhen testing according to A.3.2 and A.3.4, there shall be no air or water leakage. When testing according to A.3.3, no air shall enter. The injection piece shall be able to inject into the pipeline. When testing according to A.4, water leakage shall not exceed one drop. The injection piece shall be located at the accessory of male conical joint.7 Chemical requirementsGB 8368 is applicable.8 Biological requirementsGB 8368 is applicable.9 PackagingGB 8368 is applicable.10 LabelsSingle packaging shall have at least the following information. ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of YY/T 0286.4-2020 be delivered?Answer: The full copy PDF of English version of YY/T 0286.4-2020 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of YY/T 0286.4-2020_English with my colleagues?Answer: Yes. The purchased PDF of YY/T 0286.4-2020_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- YY/T 0286.4-2020 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.Question 5: Should I purchase the latest version YY/T 0286.4-2020?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version YY/T 0286.4-2020 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically.How to buy and download a true PDF of English version of YY/T 0286.4-2020?A step-by-step guide to download PDF of YY/T 0286.4-2020_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "YY/T 0286.4-2020". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
