GB 9840-2017 PDF EnglishUS$230.00 · In stock · Download in 9 seconds
GB 9840-2017: Feed Additive - Vitamin D3 (powder form) Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid GB 9840: Historical versions
Similar standardsGB 9840-2017: Feed Additive - Vitamin D3 (powder form)---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GB9840-2017GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 65.120 B 46 Replacing GB/T 9840-2006 Food additive - Vitamin D3 (powder form) Issued on. OCTOBER 14, 2017 Implemented on. MAY 01, 2018 Issued by. General Administration of Quality Supervision, Inspection and Quarantine of PRC; Standardization Administration of PRC. Table of ContentsForeword... 3 1 Scope... 5 2 Normative references... 5 3 Requirements... 6 4 Test method... 7 5 Inspection rules... 17 6 Labeling, packaging, transportation, storage... 18 7 Shelf life... 18 Appendix A (Informative) System suitability map and standard solution map of vitamin D3... 19ForewordChapter 1, Chapter 3, Chapter 5 of this standard are mandatory; the rest are recommended. This standard was drafted in accordance with the rules given in GB/T 1.1-2009. This standard replaces GB/T 9840-2006 "Feed additive - Vitamin D3 beadlets". Compared with GB/T 9840-2006, the main differences on the technical content of this standard are as follows. - In this standard, ADD the relevant technical requirements for the water- dispersed products of feed additive vitamin D3 (powder form). - The English name of the original standard is "Feed additive - Vitamin D3 beadlets". In this standard, CHANGE the name into "Food additive - Vitamin D3 (powder form)". - In the original standard, it is stated that "This standard applies to... as a vitamin feed additive". In this standard, CHANGE it into that "This standard applies to the common feed additive vitamin D3 (powder form), which is made using the feed additives vitamin D3 oil as raw materials, supported with a certain amount of antioxidants, adding such auxiliary materials as gelatin, starch; as well as the water-dispersible feed additive vitamin D3 (powder form), which is made by adding such auxiliary materials as maltodextrin and emulsifiers. The auxiliary materials shall comply with the provisions of the "Catalogue of feed ingredients", "Catalogue of feed additives", "Feed hygienic standards". - CHANGE the chemical name "9,10-opened cholesteryl-5,7,10(19)-triene- 3β-ol" in the original standard, into "(3β,5Z,7E)-9, 10-opened cholesteryl- 5,7,10(19)-trien-3-ol" in this standard. - CHANGE the range of the content in the technical indicators in the labeling amount from "90.0% ~ 120.0%" in the original standard, into "90.0% ~ 110.0%" in this standard. - In the technical indicators of this standard, ADD the limit requirements for the hygienic indicators, such as heavy metals, total arsenic, chromium. - In the determination method of the vitamin D3 content, CHANGE the detection wavelength from 265 nm to 254 nm. MODIFY the determination method of the vitamin D3 correction factor. ADD the applicability of the system. CHANGE concentration of the standard solution from 10 μg/mL to 50 μg/mL. CHANGE the sample weighing amount from 0.2 g ~ 0.5 g to about 1 g (accurate to 0.1 mg). In the second method, ADD the "constant volume of n-hexane extract". - In the original standard, it is stated that “the shelf life is not less than 12 months”. In this standard, CHANGE it into that “the shelf life of ordinary products in the original packaging is 24 months; the shelf life of water- dispersible products is 12 months”. - ADD appendix A (informative). This standard was proposed by AND shall be under the jurisdiction of the National Feed Industry Standardization Technical Committee (SAC/TC 76). Drafting organizations of this standard. Zhejiang Veterinary Drug and Feed Supervision Institute, Zhejiang Garden Biotech Co., Ltd., Zhejiang Pharmaceutical Co., Ltd. The main drafters of this standard. Shi Xingfen, Zhu Congying, Lu Weijun, Zhang Caiju, Jiang Hongjun, Chen Yong, Qian Guoping, Yao Yuanyuan, Huang Juan, Zhou Zhiqiang, Mei Na, Qiu Chengjun, Zhou Fengchao. This standard replaces the standard previously issued as follows. - GB/T 9840-1988, GB/T 9840-2006. Food additive - Vitamin D3 (powder form)1 ScopeThis standard specifies the requirements, test methods, inspection rules, labeling, packaging, transportation, storage, shelf life of feed additive vitamin D3 (powder form) products. This standard applies to the common feed additive vitamin D3 (powder form), which is made using the feed additives vitamin D3 oil as raw materials, supported with a certain amount of antioxidants, adding such auxiliary materials as gelatin, starch; as well as the water-dispersible feed additive vitamin D3 (powder form), which is made by adding such auxiliary materials as maltodextrin and emulsifiers. The auxiliary materials shall comply with the provisions of the "Catalogue of feed ingredients", "Catalogue of feed additives", "Feed hygienic standards". Chemical name. (3β, 5Z, 7E)-9,10-opened cholesteryl-5,7,10(19)-trien-3-ol Molecular formula. C27H44O Relative molecular mass. 384.64 (2007 international relative atomic mass) Chemical Structure.2 Normative referencesThe following documents are essential to the application of this document. For the dated documents, only the versions with the dates indicated are applicable to this document; for the undated documents, only the latest version (including all the amendments) is applicable to this standard. GB/T 601 Chemical reagent - Preparations of standard volumetric solutions GB/T 603 Chemical reagent - Preparations of reagent solution for use in testing method GB/T 6435 Determination of moisture in feedstuffs GB/T 6682 Water for analytical laboratory use - Specification and test methods3 Requirements3.1 Product specifications 3.1.1 500000 IU/g. 3.2 Appearance and traits This product is beige to yellow-brown particles, which has fluidity. It is easy to degrade, when exposed to heat, light or moisture, resulting in a decrease in content 3.3 Technical indicators The technical indicators shall meet the requirements of Table 1.4 Test methodExcept for special instructions, the reagents used are all analytically pure. The water, which is used in chromatographic and spectroscopic analysis, shall meet the requirements for first-grade water in GB/T 6682. 4.1 Sensory inspection Take an appropriate amount of sample. Place it in a clean, dry white porcelain dish. 4.2 Identification 4.2.1 Reagents and solutions 4.2.1.1 Trichloromethane. 4.2.1.2 Acetic anhydride. 4.2.2 Identification test Weigh about 100 mg of specimen. Add 10 mL of chloroform (4.2.1.1). Grind for a few minutes. Filter it. 4.3 Vitamin D3 content Warning. The detection process shall be operated in the dark! 4.3.1 Principle Vitamin D3 in the specimen is saponified and refluxed (the first method) or ultrasonically extracted (the second method). After extraction with n-hexane, it is injected into the chromatographic column, separated by mobile phase elution, measured at 254 nm. The external standard method is used to calculate the vitamin D3 content. 4.3.2 Reagents and solutions 4.3.2.8 Vitamin D3 standard product. content ≥ 99.0% (1 IU = 0.025 µg). 4.3.2.9 Potassium hydroxide solution. 500 g/L. 4.3.2.11 L-ascorbic acid solution. Weigh 3.5 g of L-ascorbic acid. Dissolve it in 20 mL of sodium hydroxide solution (4.3.2.10). This solution shall be newly prepared before use. 4.3.2.12 Phenolphthalein indicator solution. It is prepared according to GB/T 603. 4.3.2.13 Glycerol starch lubricant. Weigh 22 g of glycerol. Add 9 g of soluble starch. Heat to 140 °C. Keep it for 30 min. Stir constantly. Let it cool naturally. 4.3.2.14 Sodium chloride solution. 100 g/L. 4.3.3 Instruments and equipment 4.3.3.1 Analytical balance. Sensitivity is 0.1 mg and 0.01 mg. 4.3.3.2 Constant temperature water bath. 4.3.3.3 Ultrasonic cleaner. 4.3.3.4 Ultraviolet lamp. 4.3.3.5 High-performance liquid chromatograph, which is equipped with ultraviolet detector or diode array detector. 4.3.4 Measurement method The first method is suitable for the detection of vitamin D3 in ordinary and water- dispersible feed additives (powder forms). The second method is suitable for the detection of vitamin D3 in ordinary feed additives (powder forms). 4.3.4.1 Preparation of standard solution 4.3.4.3 Determination 4.3.4.3.1 Reference chromatographic conditions The reference chromatographic conditions are as follows. 4.6 mm, particle size 5 μm or equivalent; 4.3.4.3.2 System suitability Take 5 mL of vitamin D3 standard stock solution (4.3.4.1.1). Place it in a glass container, which has a stopper. Lead in nitrogen. Seal it tightly. Heat it in a water bath at 90 °C for 1 hour. Take it out and cool it quickly. Add 5 mL of n-hexane (4.3.2.1). 4.3.4.4 Determination of pre-vitamin D3 correction factor Pipette 5.00 mL of vitamin D3 standard stock solution (4.3.4.1.1), into a 100 mL (200 mL for the second method) brown volumetric flask. 4.3.4.5 Quantitative determination of specimen Pass the vitamin D3 standard solution (4.3.4.1.2) and the specimen solution (4.3.4.2.1 or 4.3.4.2.2) through a 0.45 μm filter membrane. Inject the sample according to the above-specified chromatographic conditions (4.3.4.3.1), for analysis, to obtain the peak area of vitamin D3 and the peak area of pre-vitamin D3. 4.4 Grain size Weigh about 50 g of the specimen. Pour it into the test sieve. Shake for a few minutes. Take the material under sieve. Weigh it. 4.5 Loss on drying It is determined according to GB/T 6435. 4.6 Heavy metals 4.6.1 Reagents and solutions 4.6.1.1 Sulfuric acid. Note. Sulfuric acid is a strong corrosive liquid. Operators need to wear protective glasses and gloves, to prevent burns. 4.6.1.2 Nitric acid. 4.6.1.3 Hydrochloric acid. 4.6.2 Analytical procedures 4.6.2.1 Preparation of specimen solution Weigh 1 g of the specimen (accurate to 10 mg). Place it in a porcelain crucible. Slowly burn it, until it is completely carbonized. 4.6.2.2 Preparation of standard colorimetric solution Take another reagent for preparing the specimen solution. Put it in a porcelain crucible. Evaporate to dryness. Add 2.0 mL of acetate buffer (4.6.1.10) and 15 mL of water. Slightly heat to dissolve it. Transfer it into a Nessler colorimetric tube. Add water 1.00 mL of the lead standard working solution (4.6.1.12). Then use water to dilute it to 25 mL, which is used as the tube A. 4.7 Total arsenic 4.7.1 Reagents and solutions 4.7.1.1 Hydrochloric acid. 4.7.1.2 Magnesium oxide. 4.7.2 Analytical procedures 4.7.2.1 Preparation of specimen arsenic spot Weigh 1.0 g of specimen (accurate to 10 mg) in a porcelain crucible. Add 10 mL of magnesium nitrate solution (4.7.1.5) and 1 g of magnesium oxide (4.7.1.2). Mix well. Soak for 4 h. Evaporate dryness on low temperature or water bath. Slowly burn with a small fire, until it is fully carbonized. Let it cool naturally. Burn it at 550 °C to completely ash it. 4.7.2.2 Preparation of standard arsenic spot Take another reagent for preparing the specimen arsenic spot. Put it in a porcelain crucible. Treat it in the same way as the specimen. Transfer it into a conical flask. Add 5 mL of hydrochloric acid (4.7.1.1) and 21 mL of water. Then add 2.00 mL of arsenic standard working solution (4.7.1.11). Operate in the same way from "Potassium iodide solution" under "Preparation of specimen arsenic spot" (4.7.2.1). 4.8 Chromium It is determined, according to the atomic absorption spectrometry (flame method) in GB/T 13088. 4.9 Dispersibility in water Weigh about 1 g of the water-dispersible specimen (accurate to 100 mg), in a 200 mL beaker. Add about 100 mL of water at 20 °C. Stir for 5 minutes, to form a homogeneous emulsion. Let it stand for 30 minutes. There shall be neither stratification nor precipitation.5 Inspection rules5.1 Sampling method It is performed according to GB/T 14699.1. 5.2 Group-batch A production batch is made of uniform products, which are produced continuously or by the same shift, using the same raw material AND the same production process. 5.4 Type inspection Type inspection items are all the requirements of Chapter 3.When the product is in normal production, type inspection shall be carried out at least once every six months. However, in one of the following situations, type inspection shall also be carried out. 5.5 Judgment rules When an indicator of the inspection result does not meet the requirements of this standard, it shall be re-sampled from twice the volume of the packaging unit, for re-inspection.6 Labeling, packaging, transportation, storage6.1 Label It shall meet the requirements of GB 10648. 6.2 Packaging Use airtight, light-proof packaging. The packaging materials shall be non-toxic and harmless. It shall meet the requirements of the corresponding standards. 6.4 Storage This product shall be stored in a ventilated, dry and dark place below 25 °C. It is forbidden to store it, together with toxic and harmful substances.7 Shelf lifeUnder the specified packaging and storage conditions, the shelf life of ordinary products in the original packaging is 24 months; the shelf life of water- dispersible products is 12 months. ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB 9840-2017 be delivered?Answer: The full copy PDF of English version of GB 9840-2017 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB 9840-2017_English with my colleagues?Answer: Yes. The purchased PDF of GB 9840-2017_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB 9840-2017 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.Question 5: Should I purchase the latest version GB 9840-2017?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB 9840-2017 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically.How to buy and download a true PDF of English version of GB 9840-2017?A step-by-step guide to download PDF of GB 9840-2017_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB 9840-2017". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
