GB/T 8923.4-2013 English PDF

US$394.00 · In stock
Delivery: <= 3 days. True-PDF full-copy in English will be manually translated and delivered via email.
GB/T 8923.4-2013: Preparation of steel substrates before application of paints and related products -- Visual assessment of surface cleanliness -- Part 4: Initial surface conditions, preparation grades and flash rust grades in connection with high-pressure water jetting
Status: Valid

Standard ID	USD	BUY PDF	Lead-Days	Standard Title (Description)	Status
GB/T 8923.4-2013	394	Add to Cart	3 days	Preparation of steel substrates before application of paints and related products -- Visual assessment of surface cleanliness -- Part 4: Initial surface conditions, preparation grades and flash rust grades in connection with high-pressure water jetting	Valid

Similar standards

GB/T 9799   GB/T 11376   GB/T 9793   GB/T 4948   GB/T 8923.1   GB/T 8923.3   

Basic data

Standard ID: GB/T 8923.4-2013 (GB/T8923.4-2013)
Description (Translated English): Preparation of steel substrates before application of paints and related products -- Visual assessment of surface cleanliness -- Part 4: Initial surface conditions, preparation grades and flash rust grades in connection with high-pressure water jetting
Sector / Industry: National Standard (Recommended)
Classification of Chinese Standard: A29
Classification of International Standard: 25.220.10
Word Count Estimation: 20,281
Quoted Standard: ISO 4628-3; ISO 8501-1; ISO 8502; ISO 8503
Adopted Standard: ISO 8501-4-2006, IDT
Regulation (derived from): National Standards Bulletin 2013 No. 10
Issuing agency(ies): General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China, Standardization Administration of the People's Republic of China

GB/T 8923.4-2013: Preparation of steel substrates before application of paints and related products -- Visual assessment of surface cleanliness -- Part 4: Initial surface conditions, preparation grades and flash rust grades in connection with high-pressure water jetting

---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order.
Preparation of steel substrates before application of paints and related products Visual assessment of surface cleanliness Part 4. Initial surface conditions, preparation grades and flash rust grades in connection with high-pressure water jetting ICS 25.220.10 A29 National Standards of People's Republic of China Steel substrates before application of paints and surfaces Visual assessment of cleanliness - Part 4. high Pressure water jetting treatment-related initial surface State, the process level and flash rust grades Part 4. Initialsurfaceconditions, preparationgradesandflashrust (ISO 8501-4.2006, IDT) Issued on. 2013-12-01 2013-07-19 implementation Administration of Quality Supervision, Inspection and Quarantine of People's Republic of China Standardization Administration of China released

Foreword

GB/T 8923 "steel substrates before application of paints Visual assessment of surface cleanliness" is divided into the following sections. --- Part 1. uncoated steel surfaces and fully remove the original steel surface coating after Rust grades and preparation grades; --- Part 2. coated steel surface has a partial removal of previous coatings after processing level; --- Part 3. surface defects of welds, edges and other areas of the processing level; --- Part 4. with high-pressure water jetting treatment-related initial surface state, the process level and flash rust grades. This section GB/T 48923 Part of. This section drafted in accordance with GB/T 1.1-2009 given rules. This section uses the translation method identical with ISO 8501-4.2006 "before application of paints and surface treatment of steel surface cleanliness Visual assessment Part 4. with high-pressure water jetting treatment-related initial surface state, the process level and flash rust grades. " Consistency correspondence between this part of international documents and normative references of our files are as follows. --- GB/T 8923.1-2011 steel substrates before application of paints and visual assessment of surface cleanliness - Part 1. uncoated Cover over the steel surfaces and steel surfaces after overall removal of previous coatings Rust grades and grade (ISO 8501-1. 2007, IDT) --- GB/T 13288 (all parts) steel surface steel substrates before application of paints and the roughness characteristics of blast - cleaned [ISO 8503 (all parts)] Qualification Test --- GB/T 18570 (all parts) steel substrates before application of paints and surface cleanliness [ISO 8502 (the Part)] This part is proposed by the China State Shipbuilding Corporation. This part of the National Standardization Technical Committee before painting and metal surface treatment and painting processes Technical Committee paint pigment (SAC / TC5/SC6) centralized. This section drafted by. China Shipbuilding Technology and Economy Research Institute, China Shipbuilding Industry Corporation 11th Institute, Jiangsu Province Fairmont 513 Limited, Zhangjiagang Shunchang Chemical Co., Ltd. The main drafters of this section. Song Yanyuan, Fu Jianhua, Gu Changchun, Gufeng Ping, Pei Lei. Steel substrates before application of paints and surfaces Visual assessment of cleanliness - Part 4. high Pressure water jetting treatment-related initial surface State, the process level and flash rust grades

1 Scope

This section GB/T 8923 specifies the high-pressure water jet to clear or partially remove water-soluble contaminants, rust, coatings and coated outer To a series of steel surface treatment after the impurity level. By common definition of various grades and typical narrative model photos. In addition, the Department Points also provides an initial surface condition and clean up after flash rust grades, also defined by a common narrative and typical model photos. Note 1. The foreign substances including salt, dirt, dust, scale, oil, grease, and marine organisms (such as algae). This section describes the state of the surface clean visual appearance, in most cases, be sufficient to meet the requirements, however, it is likely to storm Coating exposed to harsh environmental conditions such as water immersion and continuous condensation, etc., should consider the use of physical and chemical specified in various parts of ISO 8502 Methods already evaluated visually clean surface of soluble salts and other invisible contaminants tested detection. Although by high-pressure water jetting treatment will not produce a rough surface roughness or caused significant changes in existing, but the surface roughness Characteristics can still reference the provisions of ISO 8503. Note 2. The water pressure, water volume, nozzle design, and the distance from the moving speed of the impact is clear as water-soluble contaminants, rust and other contaminants and coating clear In addition to the factors of efficiency, the removal efficiency also depends on whether the cleaning process cleaning agents. If used, followed by the need for clean water with clean Wash.

2 Normative references

The following documents for the application of this document is essential. For dated references, only the dated version suitable for use herein Member. For undated references, the latest edition (including any amendments) applies to this document. Evaluation of the number and size of the ISO 4628-3 Paints and varnishes - Evaluation of degradation of coatings as well as the appearance of defects balanced degree of change Part 3. Evaluation of corrosion level (Paintsandvarnishes-Evaluationofdegradationofcoatings-Designation ofquantityandsizeofdefects, andofintensityofuniformchangesinappearance-Part 3. Assessment ofdegreeofrusting) ISO 8501-1 steel before application of paints and surface cleanliness - Visual assessment - Part 1. uncoated steel sheet Rust grades and preparation grades of steel surfaces and the surface of the full removal of previous coatings after (Preparationofsteelsubstratesbefore applicationofpaintsandrelatedproducts-Visualassessmentofsurfacecleanliness-Part 1. Rust gradesandpreparationgradesofuncoatedsteelsubstratesandofsteelsubstratesafteroveralremoval ofpreviouscoatings) ISO 8502 steel substrates before application of paints and assessment of surface cleanliness test (Preparationofsteelsubstrates beforeapplicationofpaintsandrelatedproducts-Testsfortheassessmentofsurfacecleanliness) ISO 8503 steel substrates before application of paints and steel surface roughness characteristics (Preparationofsteel after the blast - cleaning substratesbeforeapplicationofpaintsandrelatedproducts-Surfaceroughnesscharacteristicsof blast-cleanedsteelsubstrates) ......

Image     

Tips & Frequently Asked Questions:

Question 1: How long will the true-PDF of GB/T 8923.4-2013_English be delivered?

Answer: Upon your order, we will start to translate GB/T 8923.4-2013_English as soon as possible, and keep you informed of the progress. The lead time is typically 1 ~ 3 working days. The lengthier the document the longer the lead time.

Question 2: Can I share the purchased PDF of GB/T 8923.4-2013_English with my colleagues?

Answer: Yes. The purchased PDF of GB/T 8923.4-2013_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.

Question 3: Does the price include tax/VAT?

Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countries

Question 4: Do you accept my currency other than USD?

Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay.