GB/T 6132-2021 English PDFUS$184.00 ยท In stock
Delivery: <= 3 days. True-PDF full-copy in English will be manually translated and delivered via email. GB/T 6132-2021: Interchangeability dimensions for milling cutter or milling cutter arbors Status: Valid GB/T 6132: Historical versions
Basic dataStandard ID: GB/T 6132-2021 (GB/T6132-2021)Description (Translated English): Interchangeability dimensions for milling cutter or milling cutter arbors Sector / Industry: National Standard (Recommended) Classification of Chinese Standard: J41 Word Count Estimation: 10,122 Issuing agency(ies): State Administration for Market Regulation, China National Standardization Administration GB/T 6132-2021: Interchangeability dimensions for milling cutter or milling cutter arbors---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order.Interchangeability dimensions for milling cutter or milling cutter arbors ICS 25.100.20 CCSJ41 National Standards of People's Republic of China Replace GB/T 6132-2006 Interchangeable size of milling cutter and milling cutter arbor (ISO 240.2016,Milingcutters-Interchangeabilitydimensions Released on 2021-08-20 2022-03-01 implementation State Administration of Market Supervision and Administration Issued by the National Standardization Management Committee ForewordThis document is in accordance with the provisions of GB/T 1.1-2020 "Guidelines for Standardization Work Part 1.Structure and Drafting Rules of Standardization Documents" Drafting. This document replaces GB/T 6132-2006 "Interchangeable Dimensions of Milling Cutters and Milling Cutter Bars". Compared with GB/T 6132-2006, except for the structure In addition to adjustments and editorial changes, the main technical changes are as follows. a) In the scope, delete "This standard gives two sets of tables for key drive and end key drive" and "In Appendix A, the meter Conversion table for conversion of system values to corresponding English system values" (see Chapter 1 of the.2006 edition); b) The symbol mark of diameter d in Figure 1 is changed (see Figure 1, Figure 1 of the.2006 edition); c) The symbol mark of diameter d in Figure 2 is changed (see Figure 2, Figure 2 of the.2006 edition); d) Delete Appendix A and add a new Appendix A (see Appendix A, Appendix A of the.2006 edition). The translation method used in this document is equivalent to ISO 240.2016 "Interchangeable Dimensions of Milling Cutter and Milling Cutter Arbor or Milling Cutter Mandrel". This document has added two chapters. "Normative Reference Documents" and "Terms and Definitions". Compared with ISO 240.2016, this document has made the following editorial changes. ---In order to coordinate with the existing standards, the standard name is changed to "Interchangeable Dimensions of Milling Cutters and Milling Cutters". Please note that some of the contents of this document may involve patents. The issuing agency of this document is not responsible for identifying patents. This document was proposed by China Machinery Industry Federation. This document is under the jurisdiction of the National Tool Standardization Technical Committee (SAC/TC91). Drafting organizations of this document. Chengdu Tool Research Institute Co., Ltd., Sentai Inge (Chengdu) CNC Tool Co., Ltd., Chongqing Electronic Engineering Co., Ltd. Cheng Vocational College of Intelligent Manufacturing and Automobile College. The main drafters of this document. Zeng Yuhuan, Xia Keyao, Li Haixia, Ding Wei. This document was first published in.2006, and this is the first revision. Interchangeable size of milling cutter and milling cutter arbor1 ScopeThis document specifies the interchangeable dimensions between the milling cutter and the milling cutter shank or mandrel, that is. the diameter of the inner hole, the shank or the mandrel, and the key or end key transmission. The elements of movement. This document is applicable to all kinds of milling cutters installed on the arbor or mandrel.2 Normative referencesThere are no normative references in this document.3 Terms and definitionsThere are no terms and definitions that need to be defined in this document.4 Type and size4.1 Key drive The type and size of the key drive are shown in Figure 1 and Table 1. Figure 1 Key drive ......Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of GB/T 6132-2021_English be delivered?Answer: Upon your order, we will start to translate GB/T 6132-2021_English as soon as possible, and keep you informed of the progress. The lead time is typically 1 ~ 3 working days. The lengthier the document the longer the lead time.Question 2: Can I share the purchased PDF of GB/T 6132-2021_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 6132-2021_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay.Question 5: Should I purchase the latest version GB/T 6132-2021?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 6132-2021 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically. |
