GB/T 6117.1-2010 English PDFUS$139.00 · In stock
Delivery: <= 3 days. True-PDF full-copy in English will be manually translated and delivered via email. GB/T 6117.1-2010: End mills -- Part 1: Milling cutters with parallel shanks Status: Valid GB/T 6117.1: Historical versions
Basic dataStandard ID: GB/T 6117.1-2010 (GB/T6117.1-2010)Description (Translated English): End mills -- Part 1: Milling cutters with parallel shanks Sector / Industry: National Standard (Recommended) Classification of Chinese Standard: J41 Classification of International Standard: 25.100.20 Word Count Estimation: 6,689 Date of Issue: 2010-11-10 Date of Implementation: 2011-03-01 Older Standard (superseded by this standard): GB/T 6117.1-1996 Quoted Standard: GB/T 6131.1; GB/T 6131.2; GB/T 6131.3; GB/T 6131.4 Adopted Standard: ISO 1641-1-2003, MOD Regulation (derived from): National Standard Approval Announcement 2010 No.8 (Total No.163) Issuing agency(ies): General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China, Standardization Administration of the People's Republic of China Summary: This standard specifies the general shank end mills, Weldon shank end mills, 2 �� beveled straight shank cutter, basic requirements of size and markings, threaded shank end mill type. This section applies to a diameter greater than 1. 9 mm ~ 75mm straight shank cutter. GB/T 6117.1-2010: End mills -- Part 1: Milling cutters with parallel shanks---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order.End mills Part 1. Milling cutters with parallel shanks ICS 25.100.20 J41 National Standards of People's Republic of China Replacing GB/T 6117.1-1996 End mill Part 1. straight shank end mill Endmils-Part 1. Milingcutterswithparalelshanks (ISO 1641-1.2003, Endmilsandslotdrils- Part 1. Milingcutterswithcylindricalshanks, MOD) Issued on. 2010-11-10 2011-03-01 implementation Administration of Quality Supervision, Inspection and Quarantine of People's Republic of China Standardization Administration of China released ForewordGB/T 6117 "end mill" consists of three parts. --- Part 1. straight shank end mills; --- Part 2. Morse taper shank end mills; --- Part 3. 7.24 shank cutter. This part of GB/T 16117 Part of. The partial modification of international standards ISO 1641-1.2003 "keyway cutter and milling cutter - Part 1. straight shank cutter." This section according to ISO 1641-1.2003 redrafted. This part of ISO 1641-1.2003 has compared the following editorial changes and technical differences. --- Remove the foreword to international standards; --- Used instead of using decimal comma ",". ","; --- Normative documents column items, ISO 3338-1 with our standard GB/T 6131.1 in place, ISO 3338-2 with our standards GB/T 6131.2 in place, ISO 3338-3 with our standard GB/T 6131.4 substitute; --- Increase the marked sample; --- Increased 2 ° beveled straight shank cutter type and size; --- Increased coarse teeth, tooth, Teeth fine teeth; --- Remove the ISO 1641-1.2003 in ball mills and keyway cutters legend; --- Remove the ISO 1641-1.2003 Table 1 keyway cutters, short dimension; --- Remove the ISO 1641-1.2003 in Table 2. This Part replaces GB/T 6117.1-1996 "mills - Part 1. straight shank end mill type and size." This portion of the GB/T 6117.1-1996 have compared the following changes. --- Added "foreword"; --- Table 1 Recommended diameter d increase in size 24; --- Delete the contents of Chapter 3 symbols; --- According to GB/T 1.1 format requirements for the preparation of editorial changes were made. This part is proposed by China Machinery Industry Federation. This part of the tool by the National Standardization Technical Committee (SAC/TC91) centralized. This part mainly drafted by. Chengdu into a tool Group Co., Ltd., Chengdu Tool Research Institute, Shanghai Tool Works Co., Ltd. The main drafters of this section. Zhao Qing, Yansong Bo, Huang Hua new, check States soldiers, Li Zheng Wei, Zhang. This part of the standard replaces the previous editions are. --- GB 1110 ~ 1111-1973, GB 1110-1985; --- GB 6116-1985; --- GB/T 6117.1-1996. End mill Part 1. straight shank end mill1 ScopeThis section GB/T 6117 specifies the general straight shank end mill, flatted straight shank end mills, 2 ° beveled straight shank end mill, milling threaded shank Basic requirements knife type, size and marking like. This section applies to a diameter greater than 1.9mm ~ 75mm straight shank cutter.2 Normative referencesThe following documents contain provisions which, through reference in this part of the GB/T 6117, constitute provisions of this part. For dated reference documents Member, all subsequent amendments (not including errata content) or revisions do not apply to this section, however, encouraged to reach under this section Parties to research agreement to use the latest versions of these documents. For undated reference documents, the latest versions apply to this section. GB/T 6131.1 cutter straight shank - Part 1. General straight shank type and size (GB/T 6131.1-2006, ISO 3338-1. 1996, IDT) GB/T 6131.2 cutter straight shank - Part 2. flatted straight shank type and size (GB/T 6131.2-2006, ISO 3338-2. 2000, MOD) GB/T 6131.3 cutter straight shank - Part 3. 2 ° beveled straight shank types and dimensions GB/T 6131.4 cutter straight shank - Part 4. threaded shank type and size (GB/T 6131.4-2006, ISO 3338-3. 1996, IDT)3 type and size3.1 straight shank end mill according shank type divided into four different types, shown in Figure 1 to 4. Straight shank end mill dimensions in Table 1. Straight shank end mill according blade length is divided into different standard series and long series.1 ordinary straight shank end millFigure 2 flatted straight shank end mill ...... |
