GB/T 5976-2006 PDF EnglishUS$70.00 · In stock · Download in 9 seconds
GB/T 5976-2006: Wire rope grips Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid GB/T 5976: Historical versions
Similar standardsGB/T 5976-2006: Wire rope grips---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT5976-2006J 80 NATIONAL STANDARD OF THE PEOPLE'S REPUBLIC OF CHINA Replacing GB/T 5976-1986 Wire Rope Grips Issued on: APRIL 03, 2006 Implemented on: SEPTEMBER 01, 2006 Jointly Issued by the General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China and the Standardization Administration of the People's Republic of China Table of ContentsForeword ... I 1 Scope ... 1 2 Normative References ... 1 3 Types and Dimensions... 2 4 Technical Requirements ... 8 5 Inspection Rules ... 9 6 Marking, Packing, Transport and Storage ...11 Appendix A (Informative) Use Method of Wire Rope Grips ... 12 IForeword This standard replaces GB/T 5976-1986 "Wire Rope Grips". Compared with GB/T 5976-1986, this standard has the following main changes. ——Add "foreword"; ——Delete H3 dimension in Figure 3 and L1 dimension in Table 3; ——Modify the sampling methods in inspection rules; ——Modify the installation quantity of wire rope grips and the specification range of wire ropes in Appendix A. Appendix A of this standard is informative. This standard is proposed by China Machinery Industry Federation. This standard is under the jurisdiction of the National Technical Committee on Lifting Appliance of Standardization Administration of China (SAC/TC 227). Drafting organization of this standard. Dalian Daqi Group Co., Ltd. Chief drafting staff of this standard. Ding Zhiqiang, Liu Daqiang. The previous edition of the standard replaced by this standard is as. ——GB/T 5976-1986. 1NATIONAL STANDARD OF THE PEOPLE'S REPUBLIC OF CHINA Wire Rope Grips1 ScopeThis standard specifies the types and dimensions, technical requirements, inspection rules, marking, packing, transport and storage of wire rope grips. This standard is applicable to wire rope grips for rope end fixation or connection of round strand wire ropes in GB 8918-2006 and GB/T 20118-2006 used under such heavy operating conditions as crane, mine haulage, ship and building industry (hereinafter referred to as "rope grips").2 Normative ReferencesThe following standards contain provisions which, through reference in this text, constitute provisions of this standard. For dated reference, subsequent amendments to (excluding correction to), or revisions of, any of these publications do not apply. However, all parties coming to an agreement according to this standard are encouraged to study whether the latest edition of these documents is applicable. For undated references, the latest edition of the normative document is applicable to this standard. GB/T 41-2000 "Hexagon Nuts-Product Grade C" GB/T 196-2003 "General Purpose Metric Screw Threads-Basic Dimensions" (ISO 724.1993, MOD) GB/T 197-2003 "General Purpose Metric Screw Threads-Tolerances" (ISO 965-1.1998, MOD) GB/T 700-1988 "Carbon Structural Steels" GB/T 1348-1988 "Spheroidal Graphite Iron Castings" GB 8918-2006 "Steel Wire Ropes for Important Purposes" GB/T 9440-1988 "Malleable Iron Castings" GB/T 11352-1989 "Carbon Steel Castings for General Engineering Purpose" GB/T 13384-1992 "General Specifications for Packing of Mechanical and Electrical Product" GB/T 20118-2006 "Steel Wire Ropes for General Purpose" 94.3 U bolts 4.3.1 U bolts shall be refined; the screw surface shall be free from overburnt crack, indentation, scar, striation, scale and floating rust. 4.3.2 The thread surface shall be free from bumping, burr, double cusp, scratch, crack and imperfect thread. 4.3.3 The basic dimension of thread shall meet the requirements of GB/T 196-2003; the thread tolerance shall meet the requirements of GB/T 197-2003; and the tolerance grade shall be 6g. 4.3.4 The dimension deviation not given shall not be greater than 50 + % of its basic dimension, and the thread length deviation is +2 screw pitch. 4.4 Hexagon nuts The nuts shall meet the requirements of GB/T 41-2000, with a performance grade of Grade 5. 4.5 Galvanizing 4.5.1 The grip holders, U bolts and hexagon nuts (unless otherwise agreed by the supplier and the purchaser) shall be subjected to hot dip galvanizing (U bolts and nuts with specifications 6 and 8 may adopt electrogalvanizin). The galvanizing coat mass of single specimen shall not be less than 450g/m2 and the average value shall not be less than 500g/m2. 4.5.2 The surface of parts subjected to hot dip galvanizing shall be smooth and flat and free from such defects as galvanizing missing affecting use and appearance, zinc granule, bubble, crack and peeling. 4.6 Assembly The nut and grip holder shall be contacted well and free from any gap. The use method of wire rope grips is detailed in Appendix A.5 Inspection Rules5.1 The rope grips shall be inspected by the supplier. The supplier shall ensure each batch of rope grips meets the requirements of this standard and is accompanied by product quality certificate. 5.2 The rope grips shall be delivered in batch for acceptance. The specification, material designation and production process of each batch of rope grips shall be same. For castings, each cast number may be deemed as one batch. 5.3 The inspection adopts the sampling method for two times by the piece. Namely n1 group of samples shall be randomly taken for each specification from a batch of rope grips for acceptance, if the unqualified group number therein is not greater than C1 group, this batch of rope grips may be subjected to acceptance. If greater than or equal to C2 group, this batch of rope grips shall not be subjected to acceptance. If greater than C1 group but less than C2 group, the second sampling inspection shall be carried out, and another n2 group of samples shall be taken from this batch of rope grips. If the sum of unqualified group number in taken samples for two times (n1+n2) is less than C2 group, acceptance shall be carried out; if greater than or equal to C2 group, acceptance shall not be carried out. a The test bar with performance inspection shall be taken from the same cast number of the same furnace for castings. b If several dimensions and defects of one grip holder are unqualified, only 1 piece shall be calculated. c This batch is randomly inspected once. 5.7 The purchaser is entitled to carry out acceptance inspection for the rope grips supplied by the supplier in accordance with the requirements of 5.3~5.6.6 Marking, Packing, Transport and Storage6.1 Each grip holder shall be provided with the marks of permanent and legible specification, material and supplier name (or trademark). Such marks shall be in the position shown in Figure 2. 6.2 The packing types and materials for rope grips must consider the rope grips shall be free from damage and corrosion during transport and maintaining period, and shall meet the requirements of GB/T 13384. 6.3 The rope grips shall be ensured free from rust within a year as date of delivery during the storage period under normal transport and maintaining conditions. 6.4 The appearance of packing boxes, cases, bags, etc. shall be provided with marks or labels, with the content as follows. a) Supplier name or trademark; b) Product name; c) Specification and quantity; d) Delivery number and standard code; e) Manufacturing date and delivery date; f) Destination and consignee; g) Box number, gross weight, net weight and volume; h) Damp-proof mark. 6.5 The requirements beyond above-mentioned provisions shall be negotiated by the supplier and the purchaser.Appendix A(Informative) Use Method of Wire Rope Grips A.1 Arrangement of wire rope grips For wire rope grips, the grip holder is buckled on the working segment of wire rope as shown in Figure A.1, and the U bolt is buckled on the tail segment of wire rope. The wire rope grips shall be free from alternate arrangement on the wire rope. Figure A.1 Correct Arrangement Method of Wire Rope Grips A.2 Quantity of wire rope grips For applicable places meeting the requirements of this standard, the minimum quantity of wire rope grips required for each junction is recommended as Table A.1. Table A.1 Specification of rope grip (nominal diameter of wire rope) dr/mm Minimum quantity of wire rope grips/group ≤18 >18~26 >26~36 >36~44 >44~60 A.3 Distance between wire rope grips The distance A between wire rope grips is equal to 6~7 times the diameter of wire rope. A.4 Strength at rope grip fixation The strength at wire rope grip fixation depends on the correct arrangement of rope grip on wire rope, as well as the caution and proficiency level of rope grip fixation and gripping. If the clamp nuts are inappropriate or the wire rope grips are insufficient, the rope end may have slipping at the beginning of load bearing. If the rope grips are correctly arranged and gripped according to the recommended quantity, and all the rope grip holders are in the longer part of the wire rope, but the U bolts are in the shorter part or tail segment of the wire rope, the strength at the fixation shall be 80% of wire rope strength at least. In actual use, the rope grips, after loading bearing for one and two times, shall be checked; in many cases, the nuts shall be tightened further. A.5 Fastening of wire rope grips The fastening of rope grips must consider the reasonable load carrying of each rope grip; ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 5976-2006 be delivered?Answer: The full copy PDF of English version of GB/T 5976-2006 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 5976-2006_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 5976-2006_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 5976-2006 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.Question 5: Should I purchase the latest version GB/T 5976-2006?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 5976-2006 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically.How to buy and download a true PDF of English version of GB/T 5976-2006?A step-by-step guide to download PDF of GB/T 5976-2006_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 5976-2006". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
