GB/T 5779.3-2000 PDF EnglishUS$275.00 · In stock · Download in 9 seconds
GB/T 5779.3-2000: Fasteners. Surface discontinuities. Bolts, screws and studs for special requirements Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure GB/T 5779.3: Historical versions
GB/T 5779.3-2000: Fasteners. Surface discontinuities. Bolts, screws and studs for special requirements---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT5779.3-2000 NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 21.060.10 J 13 idt ISO 6157-3:1988 Fasteners - Surface discontinuities - Bolts, screws and studs for special requirements ISSUED ON: SEPTEMBER 26, 2000 IMPLEMENTED ON: FEBRUARY 01, 2001 Issued by: State Bureau of Quality Technical Supervision Table of ContentsForeword ... 3 ISO foreword ... 4 1 Scope ... 5 2 Normative references ... 6 3 Types, causes, appearance characteristics, limits of surface defects ... 6 4 Inspection and judgment procedures ... 17 Appendix A (Normative) Sampling scheme for surface defects ... 19 NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA Fasteners - Surface discontinuities - Bolts, screws and studs for special requirements1 Scope1.1 The limits, which are specified in this standard, apply to various types of surface defects of bolts, screws, studs with special requirements. Applicable bolts, screws, studs: The nominal diameter of the thread is equal to or greater than 5 mm; Product grades A and B; Nominal length l ≤ 10d (or longer according to special requirements); Performance grade 12.9; Performance grades 8.8, 9.8, 10.9, but shall be specified in the product standard OR in the agreement between the supplier and the buyer. 1.2 Even if the surface defects reach the allowable limits, which are specified in Chapter 3, the mechanical and working properties of the product shall still meet the minimum requirements of GB/T 3098.1. In addition, it shall meet the dimensional requirements of the corresponding product standards. When the fatigue strength is required, the fatigue strength shall not be lower than that which can be achieved by bolts without defects, in the same batch of products. Note: 1 The Figures in Chapter 3 are examples only. They apply accordingly to other types of bolts, screws, studs. 2 Some surface defects are exaggerated for clarity. idt ISO 6157-3:1988 Replacing GB/T 5779.3-19862 Normative referencesThe following standards contain provisions which, through reference in this standard, constitute provisions of this standard. At the time of publication, the editions indicated were valid. All standards are subject to revision and parties using this standard should explore the possibility of using the latest edition of the following standards. GB/T 90-1985 Acceptance inspection, marking and packaging of fasteners (eqv ISO 3269:1984) GB/T 1033-1995 Surface roughness parameters and their values (neq ISO 468:1982) GB/T 2828-1987 Sampling procedures and tables for lot-by-lot inspection by attributes (Apply to inspection of successive lots or batches) GB/T 3098.1-2000 Mechanical properties of fasteners - Bolts, screws and studs (idt ISO 898-1:1999) GB/T 15239-1994 Sampling procedures and tables for isolated lot inspection by attributes3 Types, causes, appearance characteristics, limits of surfacedefects 3.1 Cracks A crack is a well-defined (crystalline) fracture, along or across a metal grain boundary, which may contain inclusions of foreign elements. Cracks are usually caused by excessive stress in the metal, during forging or other forming processes or heat treatment. Cracks may also exist in the raw material. When the workpiece is reheated, the cracks are usually discolored by peeling of the scale. order. 4.2 Non-destructive inspection A random sample is taken from the acceptance batch, to carry out visual or other non- destructive inspection, such as magnetic technique or eddy current, as specified in Table A1 of Appendix A (Normative). If it is found that the defective samples do not exceed the allowable limit, the batch will be accepted (see also 4.4). If the number of defective samples is found to exceed the allowable limit, these unqualified products will be regarded as a batch and continue to be inspected, according to the procedure of 4.3. 4.3 Destructive inspection According to the procedure of clause 4.2, if a non-conforming product is found, then according to the provisions of Table A2 of Appendix A, the product with the most serious defect will be formed into a second sample; a section perpendicular to the defect will be taken, at the maximum depth passing through the defect, for inspection. 4.4 Judgment If quenched cracks on any part OR folds on the interior corners OR folds below bearing surface beyond the "clover leaf" shape are found on non-circular shoulder fasteners, in the process of visual inspection, the batch of products will be rejected. During destructive inspection, if forging cracks, bursts, seams and laps, voids, tool marks or damage are found beyond the specified allowable limits, the batch will be rejected. 0.08 x Head or flange diameter or 0.04 x Head or flange diameter 0.25 mm + 0.02 s (to spanner flat) 0.08 x Head or flange diameter or 0.04 x Head or flange diameter 0.25 x Socket depth 0.03 x Head diameter, maximum 0.13 mm 0.06 x Head diameter, maximum 1.6 mm ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 5779.3-2000 be delivered?Answer: The full copy PDF of English version of GB/T 5779.3-2000 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 5779.3-2000_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 5779.3-2000_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 5779.3-2000 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.Question 5: Should I purchase the latest version GB/T 5779.3-2000?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 5779.3-2000 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically.How to buy and download a true PDF of English version of GB/T 5779.3-2000?A step-by-step guide to download PDF of GB/T 5779.3-2000_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 5779.3-2000". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
