GB/T 5703-2023 PDF EnglishUS$980.00 · In stock · Download in 9 seconds
GB/T 5703-2023: Basic human body measurements for technological design Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid GB/T 5703: Historical versions
Similar standardsGB/T 5703-2023: Basic human body measurements for technological design---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT5703-2023GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 13.180 CCS A 25 Replacing GB/T 5703-2010 Basic Human Body Measurements for Technological Design (ISO 7250-1.2017, Basic human body measurements for technological design - Part 1. Body measurement definitions and landmarks, MOD) Issued on. MAY 23, 2023 Implemented on. DECEMBER 1, 2023 Issued by. State Administration for Market Regulation; Standardization Administration of the People’s Republic of China. Table of ContentsForeword... 4 Introduction... 6 1 Scope... 7 2 Normative References... 7 3 Terms and Definitions... 7 4 Measuring Conditions and Instruments... 10 4.1 Conditions... 10 4.2 Instruments... 10 4.3 Further Conditions... 11 5 Landmarks... 11 5.1 General... 11 5.2 Acromion... 11 5.3 Cervicale... 12 5.4 Crotch Level... 12 5.5 Ectocanthus... 13 5.6 Glabella... 13 5.7 Iliospinale Anterius - Anterior Superior Iliac Spine... 13 5.8 Lowest Point of the Rib Cage... 14 5.9 Menton... 15 5.10 Mesosternale... 15 5.11 Nuchale... 16 5.12 Olecranon... 16 5.13 Orbitale - Infraorbitale... 17 5.14 Opisthocranion... 17 5.15 Sellion... 18 5.16 Stylion (radial stylion)... 18 5.17 Suprapatella (sitting)... 19 5.18 Thelion... 19 5.19 Tibiale... 19 5.20 Tragion... 20 5.21 Ulnar Stylion... 20 5.22 Vertex (top of head)... 21 6 Basic Anthropometric Measurements... 22 6.1 Measurements Taken while the Subject Stands... 22 6.2 Measurements Taken while the Subject Sits... 30 6.3 Measurements on Specific Body Segments... 41 6.4 Functional Measurements... 54 Appendix A (informative) Recommended Anthropometric Terminology... 64 Bibliography... 78ForewordThis document was drafted in accordance with the rules provided in GB/T 1.1-2020 Directives for Standardization - Part 1.Rules for the Structure and Drafting of Standardizing Documents. This document serves as a replacement of GB/T 5703-2010 Basic Human Body Measurements for Technological Design. In comparison with GB/T 5703-2010, apart from structural adjustments and editorial modifications, the main technical changes are as follows. ---“longitudinal axis of the foot” is added and “styloid process” is deleted from “Terms and Definitions”, and the terms of ten bony landmark points, including “acromion” are moved to Chapter 5 “Landmarks” (see Chapter 3 and Chapter 5; Chapter 2 of Version 2010); ---The requirements for body posture are added to “measuring conditions” (see 4.1); ---The Chapter “Landmarks” is added, which provides general requirements for landmarks, as well as definitions and corresponding position diagrams of 21 landmarks (see Chapter 5); ---The form of the schematic diagrams of anthropometric measurements is modified (see Chapter 6; Chapter 4 of Version 2010); ---Six basic anthropometric measurements “thumb length”, “thumb breadth”, “hand thickness”, “hand breadth including thumb”, “arm circumference flexed” and “forearm circumference flexed” are added (see 6.3). This document modifies and adopts ISO 7250-1.2017 Basic Human Body Measurements for Technological Design - Part 1.Body Measurement Definitions and Landmarks. This document makes the following editorial modifications. ---The title of the Standard is modified from “Basic Human Body Measurements for Technological Design - Part 1.Body Measurement Definitions and Landmarks” into “Basic Human Body Measurements for Technological Design”; ---Appendix A (informative) “Correspondence between ISO 7250-1 Dimension Names and Numbers and ISO 14738 and ISI 15534 Anthropometric Dimension Codes” of ISO 7250-1.2017 is deleted. ---Appendix A (informative) “Recommended Anthropometric Terminology” is added. Please be noted that certain content of this document may involve patents. The institution issuing this document does not undertake the responsibility of identifying these patents. This document was proposed by and shall be under the jurisdiction of National Technical Committee 7 on Ergonomics of Standardization Administration of China (SAC/TC 7). The drafting organizations of this document. China National Institute of Standardization; Air Force Medical Center, PLA; Chemical Defense Research Institute of Academy of Military Sciences, PLA; Donghua University; Beijing Union University; Northeast Normal University. The main drafters of this document. Zhang Xin, Ran Linghua, Liu Taijie, Guo Xiaozhao, Zheng Xiaohui, Zheng Rong, Hu Huimin, Yang Aiping, Xu Hongqi, Ding Songtao, Luo Ling, Wang Zhongting. The issuing of the previous versions. ---Firstly issued in 1985 as GB/T 5703-1985; ---During the first revision in 1999, the content of GB/T 3975-1983 Terms of Anthropometry was incorporated; secondly revised in 2010; ---This is the third revision.1 ScopeThis document provides a description of anthropometric measurements which can be used as a basis for comparison of population groups and for the creation of anthropometric databases (see GB/T 22187). The basic list of measurements specified in this document is intended to serve as a guide for ergonomists who are required to define population groups and apply their knowledge to the geometric design of the places where people work and live.2 Normative ReferencesThis document does not have normative references.3 Terms and DefinitionsThe following terms and definitions are applicable to this document. imagined center line of the foot, connecting a point between the ankle bones, and the tip of the second toe pertaining to the long bones of the hand between the carpals (wrist bones) and the phalanges pertaining to the anteroposterior (front to back) median plane of the body (midsagittal), or to a referring to the long bone in the forearm on the little finger side4 Measuring Conditions and InstrumentsA cube, 200 mm on each side, is used for determining the maximal posterior protrusion of a seated person. A standard rod, 20 mm in diameter, and approximately 10 cm in length, is used for determining grip measurements. Chest and other measurements affected by breathing should be taken during gentle breathing.5 LandmarksMost lateral point of the lateral edge of the spine (acromial process) of the scapula, projected vertically to the surface of the skin. See Figure 1. Tip of the prominent bone at the base of the back of the neck (spinous process of the seventh cervical vertebra) in the midsagittal plane and projected posteriorly to the surface of the skin while the head is held in the Frankfurt plane. Superior point of the patella (kneecap) projected vertically to the surface of the skin, when the subject is seated and the feet are parallel with each other.6 Basic Anthropometric MeasurementsDescription. Vertical distance from the floor to the acromion. See Figure 24. Description. Vertical distance from the floor to the most downward-directed point of the iliac crest (iliospinale anterius). See Figure 26. Method. Subject first stands with legs a maximum of 100 mm apart and the movable arm of the measuring instrument is placed against the inner surface of the thigh in such a way that, when pushed higher, it gently presses against the ischial bone. ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 5703-2023 be delivered?Answer: The full copy PDF of English version of GB/T 5703-2023 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 5703-2023_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 5703-2023_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 5703-2023 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.Question 5: Should I purchase the latest version GB/T 5703-2023?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 5703-2023 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically.How to buy and download a true PDF of English version of GB/T 5703-2023?A step-by-step guide to download PDF of GB/T 5703-2023_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 5703-2023". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
