GB/T 531.1-2008 PDF EnglishUS$75.00 · In stock · Download in 9 seconds
GB/T 531.1-2008: Rubber, vulcanized or thermoplastic -- Determination of indentation hardness -- Part 1: Durometer method (Shore hardness) Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid GB/T 531.1: Historical versions
Similar standardsGB/T 531.1-2008: Rubber, vulcanized or thermoplastic -- Determination of indentation hardness -- Part 1: Durometer method (Shore hardness)---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT531.1-2008 NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 83.060 G 40 GB/T 531.1-2008 / ISO 7619-1.2004 Partially replacing GB/T 531-1999 Rubber, Vulcanized or Thermoplastic - Determination of Indentation Hardness - Part 1.Durometer Method (Shore Hardness) (ISO 7619-1.2004, IDT) Issued on. JUNE 04, 2008 Implemented on. DECEMBER 01, 2008 Issued by. General Administration of Quality Supervision, Inspection and Quarantine; Standardization Administration of PRC. Table of ContentsForeword... 3 Introduction... 5 1 Scope... 6 2 Normative References... 6 3 Principle and Selection of Shore Durometer... 7 4 Apparatus... 7 5 Test Piece... 12 6 Conditioning... 13 7 Procedure... 13 8 Calibration and Checking... 14 9 Test Report... 14 Bibliography... 16ForewordGB/T 531 Rubber Vulcanized or Thermoplastic – Determination of Indentation Hardness, includes. --- Part 1.Durometer Method (Shore Hardness); --- Part 2.IRHD Pocket Meter Method. This Part belongs to Part 1 of GB/T 531. This Part equivalently adopts the international standard ISO 7619-1.2004 Rubber Vulcanized or Thermoplastic – Determination of Indentation Hardness – Part 1. Durometer Method (Shore Hardness). For the benefit of use, the following editorial changes are made against the original ISO standard. a) Use “this Part” to replace “this International Standard”; b) Use decimal point “.” to replace the comma “,” serving as the decimal point; c) Delete the foreword of the international standard; d) Delete the Footnote 1) of the Clause 2 in the original ISO standard; the Footnote 2) in 8.2, as well as the Footnote 3) in the Bibliography. This Part replaced the Shore A, D Scale test methods in the GB/T 531-1999 Rubber – Determination of Indentation Hardness by Means of Pocket Hardness Meters; meanwhile add the AO, AM scale test methods. This Part excluded the IRHD Pocket Meter Method in the GB/T 531-1999 Rubber – Determination of Indentation Hardness by Means of Pocket Hardness Meters. The major technical differences between this Part and GB/T 531-1999 are as follows. --- Add the AO scale for rubber in low hardness range (Clause 1 of this Edition); --- Add the AM scale for thin test piece (Clause 1 of this Edition); --- Describe the use of stand in details (4.3 of this Edition); --- Introduce the regulation on the pressure foot area (4.1.1 and 4.2.1 of this Edition); --- For vulcanized rubber or unknown type of rubber, change the retention time of spring test force from “1s” to “3s”. Since the hardness value drops significantly in the first few seconds, it can give more accurate results (7.1 of 1999 Edition; 7.2 of this Edition); --- For the thermoplastic rubber, introduce 15s for the retention time of the spring test force. Because its hardness value decreases for a longer period of time against the vulcanized rubber; such time regulation is the same as that specified in ISO 868 [1] (7.2 of this Edition); --- Change the geometry tolerance of the indenter and the calibration tolerance of the spring test force; so that improve the accuracy of the durometer (4.1.2, 4.2.2, 8.1 of 1999 Edition; 4.1.2, 4.2.2, 4.4 of this Edition). This Part was proposed by China Petroleum and Chemical Industry Association. This Part shall be under the jurisdiction of Rubber Physics and Chemical Test Methods Subcommittee of National Technical Committee for Standardization of Rubber (SAC/TC 35/SC 2). Chief drafting organization of this Part. Guangdong Provincial Institute of Metrology Introduction. Participating drafting organization of this Part. Shanghai Liuling Instrument Factory. Chief drafting staffs of this Part. Chen Minghua, Gao Furong, and Tang Changshe. Participating drafting staffs of this Part. Zuo Weizhong, and Yu Guoan. The historical editions replaced by this Standard are as follows. --- GB/T 531-1965, GB/T 531-1992, GB/T 531-1999.1 ScopeThis Part specifies a method for determining the indentation hardness (Shore hardness) of vulcanized or thermoplastic rubber using durometers with the following scales.2 Normative ReferencesThe provisions in following documents become the provisions of this Part through reference in this Part. For dated references, the subsequent amendments (excluding corrigendum) or revisions do not apply to this Part, however, parties who reach an agreement based on this Part are encouraged to study if the latest versions of these documents are applicable. For undated references, the latest edition of the referenced document applies.3 Principle and Selection of Shore DurometerThe measurement principle of the shore durometer is to press the specific shape of indenter into the rubber sample under the specific conditions and form the indentation depth; then convert the indentation depth into the hardness value.4 ApparatusThe Types A, D indenters shall be formed from a hardened steel rod with diameter of 1.25 mm ± 0.15 mm; their shapes are shown in Figures 1, 2, respectively. Type AO indenter is the sphere with a radius of 2.5 mm ± 0.02 mm; its shape is shown in Figure 3.5 Test PieceThe other dimensions of the test piece shall be sufficient to permit measurements at least 12 mm away from any edge for Shore Types A and D durometers, 15 mm away from any edge for Shore Type-AO, and 4.5 mm away from any edge for Type-AM, respectively.6 ConditioningWhere practical, test pieces shall be conditioned immediately before testing for a minimum period of 1 h at the standard laboratory temperature in accordance with GB/T 2941.The same temperature shall be used throughout any single test or series of tests intended to be comparable.7 ProcedureApply a spring test force in accordance with 4.3.3 sufficient only to obtain firm contact between the pressure foot and the test piece; after that, take the reading at the specified time. Make five measurements of hardness at different positions on the test piece; then take the average value. For Shore Type-A, Type-D and Type-AO durometers, the interval for any two different positions shall be at least 6 mm; while for the Shore Type-AM durometer, the interval shall be at least 0.8mm.8 Calibration and CheckingPress the Shore Type-A durometer against a flat piece of glass and adjust the reading on the scale to give 100 IRHD. Use a set of standard rubber blocks covering the hardness range approx. 30 IRHD to 90 IRHD to calibrate it.9 Test ReportThe test report shall include the following information. ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 531.1-2008 be delivered?Answer: The full copy PDF of English version of GB/T 531.1-2008 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 531.1-2008_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 531.1-2008_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 531.1-2008 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.Question 5: Should I purchase the latest version GB/T 531.1-2008?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 531.1-2008 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically.How to buy and download a true PDF of English version of GB/T 531.1-2008?A step-by-step guide to download PDF of GB/T 531.1-2008_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 531.1-2008". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
