GB/T 4857.1-2019 PDF EnglishUS$90.00 · In stock · Download in 9 seconds
GB/T 4857.1-2019: Packaging -- Basic tests for transport packages -- Part 1: Identification of parts when testing Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid GB/T 4857.1: Historical versions
Similar standardsGB/T 4857.1-2019: Packaging -- Basic tests for transport packages -- Part 1: Identification of parts when testing---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT4857.1-2019 NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 55.020 A 80 Replacing GB/T 4857.1-1992 Packaging - Basic tests for transport packages – Part 1: Identification of parts when testing (ISO 2206:1987, Packaging - Complete, filled transport packages - Identification of parts when testing, MOD) ISSUED ON: MAY 10, 2019 IMPLEMENTED ON: DECEMBER 01, 2019 Issued by: State Administration for Market Regulation; Standardization Administration of the People’s Republic of China. Table of ContentsForeword ... 3 1 Scope ... 6 2 Identification ... 6ForewordGB/T 4857, Packaging - Basic tests for transport packages, is divided into the following parts: -- Part 1: Identification of parts when testing; -- Part 2: Temperature and humidity conditioning; -- Part 3: Stacking test methods using a static load; -- Part 4: Compression and Stacking tests using a compression tester; -- Part 5: Vertical impact test method by dropping; -- Part 6: Rolling test method; -- Part 7: Sinusoidal vibration test method at constant frequency; -- Part 9: Water spray test; -- Part 10: Sinusoidal vibration test method using at variable vibration frequency; -- Part 11: Horizontal impact test methods; -- Part 12: Water immersion test method; -- Part 13: Low pressure test; -- Part 14: Toppling test method; -- Part 15: Controlled horizontal impact test method; -- Part 17: General rules for the compilation of performance test; -- Part 19: Information to be recorded in distribution trials; -- Part 20: Bump test method; -- Part 22: Unit loads stability test methods; -- Part 23: Random vibration test method. This Part is the first part of GB/T 4857. This Part was drafted in accordance with the rules given in GB/T 1.1-2009. This Part replaces GB/T 4857.1-1992, Packaging. Complete filled transport packages. Identification of parts when testing. Compared with GB/T 4857.1- 1992, the main technical changes, except editorial changes, are as follows: -- Modify the description of the identification of parallelepiped packages (see 2.1, 2.1 of version 1992); -- Modify the name of the bag and change it to “bag package” (see 2.3, 2.3 of version 1992); -- Modify the description of the longitudinal seam in the bag package (see 2.3, 2.3 of version 1992); -- Add the identification of the envelope package (see 2.4). This Part uses the redrafting method to modify the use of ISO 2206: 1987, Packaging - Complete, filled transport packages - Identification of parts when testing. The technical differences between this Part and ISO 2206:1987 and their reasons are as follows: -- Modify 2.1; make appropriate supplement for the original content to make it clearer; -- Modify the title of 2.3; change it to "bag package” on the original basis, so as to be consistent with 2.1, 2.2, 2.4; -- Modify 2.3; change the original side seams and longitudinal seams to longitudinal seams, and express the identification in the middle or on the side to make the expression clearer; -- Add the identification of the envelope package. This Part makes the following editorial changes: -- In order to be consistent with the existing standard system, change the name of this Part to “Packaging - Basic tests for transport packages - Part 1: Identification of parts when testing”. This Part shall be under the jurisdiction of National Technical Committee 49 on Packaging of Standardization Administration of China (SAC/TC 49). The drafting organizations of this Part: China Packaging Research & Test Center, SF Technology Co., Ltd., Tianjin University of Science & Technology, Shenzhen ORT Technical Service Co., Ltd., China Packaging Research Institute Co., Ltd. Packaging - Basic tests for transport packages - Part 1: Identification of parts when testing1 ScopeThis Part of GB/T 4857 specifies the identification of parts of transport packages (hereinafter referred to as the packages) when testing. This Part applies to the identification of parts of packages; the identification of parts of packaging containers can use by reference to it.2 Identification2.1 Parallelepiped package 2.1.1 The package shall be placed in accordance with the state of transport; if the transport state is not clear, the package shall be placed in the most stable state. After it is placed, if there are seams perpendicular to the horizontal plane on the package, any of the seams shall be placed on the right side of the identifier; when the seam is parallel to the horizontal plane or there is no seam, any smaller end face of it shall be faced to the identifier. The identification is shown in Figure 1. Figure 1 2.1.2 The upper surface is identified as side 1; the right side is identified as side 2; the bottom surface is identified as side 3; the left side is identified as side 4; the near-end face is identified as side 5; the far-end face is identified as side 6. ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 4857.1-2019 be delivered?Answer: The full copy PDF of English version of GB/T 4857.1-2019 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 4857.1-2019_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 4857.1-2019_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 4857.1-2019 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.Question 5: Should I purchase the latest version GB/T 4857.1-2019?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 4857.1-2019 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically.How to buy and download a true PDF of English version of GB/T 4857.1-2019?A step-by-step guide to download PDF of GB/T 4857.1-2019_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 4857.1-2019". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
