GB/T 41641-2022 English PDF

US$404.00 · In stock
Delivery: <= 4 days. True-PDF full-copy in English will be manually translated and delivered via email.
GB/T 41641-2022: Mechanical properties measurement - Room temperature tensile test on REBCO wires
Status: Valid

Standard ID	USD	BUY PDF	Lead-Days	Standard Title (Description)	Status
GB/T 41641-2022	404	Add to Cart	4 days	Mechanical properties measurement - Room temperature tensile test on REBCO wires	Valid

Similar standards

GB/T 44030   GB/T 43354   GB/T 43091   GB/T 45597   GB/T 45169   

Basic data

Standard ID: GB/T 41641-2022 (GB/T41641-2022)
Description (Translated English): Mechanical properties measurement - Room temperature tensile test on REBCO wires
Sector / Industry: National Standard (Recommended)
Classification of Chinese Standard: H22
Classification of International Standard: 29.050; 77.040.01
Word Count Estimation: 22,254
Date of Issue: 2022-10-12
Date of Implementation: 2023-05-01
Issuing agency(ies): State Administration for Market Regulation, China National Standardization Administration

GB/T 41641-2022: Mechanical properties measurement - Room temperature tensile test on REBCO wires

---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order.
Mechanical properties measurement - Room temperature tensile test on REBCO wires ICS 29.050;77.040.01 CCSH22 National Standards of People's Republic of China Mechanical property measurement Tensile test method for REBCO strip at room temperature (IEC 61788-25.2018, Superconductivity-Part 25.Mechanicalproperties Released on 2022-10-12 2023-05-01 implementation State Administration for Market Regulation Released by the National Standardization Management Committee

table of contents

Preface I Introduction II 1 Scope 1 2 Normative references 1 3 Terms and Definitions 1 4 Principle 3 5 device 3 5.1 General 3 5.2 Testing machine 3 5.3 Extensometer 3 6 Sample preparation 3 6.1 General 3 6.2 Length of the test piece 4 6.3 Determination of cross-sectional area (SO) 4 7 Test conditions 4 7.1 Clamping of Specimen 4 7.2 Installation of extensometer 4 7.3 Test speed 4 7.4 Test 4 8 Result calculation 4 8.1 Modulus of elasticity (E) 4 8.2 0.2% of the specified plastic elongation strength (Rp0.2-0 and Rp0.2-U) 5 9 Uncertainty of measurement5 10 Test report 6 10.1 Sample 6 10.2 Results 6 Appendix A (informative) Chapter 1~Chapter 10 related additional information 7 Appendix B (informative) Evaluation of synthetic standard uncertainty of elastic modulus 12 Reference 18

foreword

This document is in accordance with the provisions of GB/T 1.1-2020 "Guidelines for Standardization Work Part 1.Structure and Drafting Rules for Standardization Documents" drafting. This document identically adopts IEC 61788-25.2018 "Superconductivity Part 25.Mechanical properties measurement REBCO strip room temperature tensile Tensile Test Method". The following minimal editorial changes have been made to this document. --- In order to coordinate with existing standards, change the name of the standard to "Mechanical Properties Measurement of REBCO Strip Tensile Test Method at Room Temperature"; --- The formula (3) in IEC 61788-25.2018 was amended and "×10-3" was added. Please note that some contents of this document may refer to patents. The issuing agency of this document assumes no responsibility for identifying patents. This document was proposed by the Chinese Academy of Sciences. This document is under the jurisdiction of the National Superconducting Standardization Technical Committee (SAC/TC265). This document is drafted by. Shanghai Superconducting Technology Co., Ltd., Shanghai Jiaotong University, Western Superconducting Materials Technology Co., Ltd., Institute of Plasma Physics, Chinese Academy of Sciences, Suzhou Institute of Advanced Materials Co., Ltd., Lanzhou University, Institute of Electrical Engineering, Chinese Academy of Sciences, Shanghai Shangchuang Superconducting Technology Co., Ltd., Institute of Physics, Chinese Academy of Sciences, Shanghai University. The main drafters of this document. Zhao Yue, Zhu Jiamin, Liu Huajun, Zhang Xingyi, Cheng Junsheng, Xiong Xuming, Cai Chuanbing, Zhang Guomin, Chen Sikan, Jiang Guangyu, Yan Guo, Li Jie.

Introduction

Several types of composite superconductors are now commercially available. Rare earth-based oxide superconductors (SC) with the chemical formula REBa2Cu3O7 can be used for To prepare practical superconducting strips, wherein the rare earth element RE is usually Y, Dy, Gd, Nd, Ho or Sm, or a combination of two or more of these elements combine. Such practical superconducting tapes are often referred to as REBCO coated conductors. Typical structures of coated conductors include Ni-Cr-Mo based alloys, Ni-W alloy or stainless steel substrate, buffer layer composed of various oxides, superconducting layer and silver protective layer. Among them, the substrate and buffer layer are conducive to Formation of biaxial textures in superconducting layers. In order to withstand large electromagnetic forces, stainless steel or copper alloy thin strips are usually used to encapsulate and strengthen the coated conductor. Commercial composite superconductors have high current densities and small cross-sectional areas, and are mainly used in power devices and superconducting magnets. When electrical equipment is manufactured and During operation, composite superconducting tapes are subject to complex stresses and strains. In a superconducting magnet, since the coil is in a high magnetic field and carries a high current density The superconducting coil will be subjected to a large electromagnetic force. Therefore, it is necessary to test the mechanical properties of REBCO superconducting tapes. Mechanical property measurement Tensile test method for REBCO strip at room temperature

1 Scope

This document describes a method and procedure for tensile testing of REBCO strip at room temperature. The test methods described in this document apply to It is used to measure elastic modulus and 0.2% specified plastic elongation strength. The data of elastic limit, breaking strength and elongation after break are for reference only. This document is suitable for testing rectangular cross-section samples with a cross-sectional area of 0.12mm2~6.0mm2 (corresponding to a width of 2.0mm~ 12.0mm, superconducting tape with a thickness between 0.06mm and 0.5mm).

2 Normative references

The contents of the following documents constitute the essential provisions of this document through normative references in the text. Among them, dated references For documents, only the version corresponding to the date is applicable to this document; for undated reference documents, the latest version (including all amendments) is applicable to this document. ISO 376 Calibration of standard dynamometers for the inspection of uniaxial testing machines for metallic materials (Metalicmaterials-Calibrationof Note. GB/T 13634-2019 Calibration of standard dynamometers for inspection of uniaxial testing machines for metallic materials (ISO 376.2011, IDT) ISO 7500-1 Inspection of static uniaxial testing machines - Part 1.Inspection and calibration of force measuring systems of tensile and (or) compressive testing machines Note. GB/T 16825.1-2008 Inspection of static uniaxial testing machines - Part 1.Inspection and calibration of force measuring systems of tensile and (or) compressive testing machines (ISO 7500-1.2004, IDT) ISO 9513 Calibration of extensometer systems for uniaxial testing of metallic materials (Metalicmaterials-Calibrationofexten- Note. GB/T 12160-2019 Calibration of Extensometer System for Uniaxial Testing of Metallic Materials (ISO 9513.2012, IDT)

3 Terms and Definitions

The following terms and definitions apply to this document as defined by the IEC and ISO online platforms. The following are the URLs of the term bases maintained by ISO and IEC for standardization work. 3.1 Tensile stress tensile stress The quotient of the tensile force at any time during the test divided by the original cross-sectional area of the specimen. 3.2 Tensile strain tensile strain ......

Image     

Tips & Frequently Asked Questions:

Question 1: How long will the true-PDF of GB/T 41641-2022_English be delivered?

Answer: Upon your order, we will start to translate GB/T 41641-2022_English as soon as possible, and keep you informed of the progress. The lead time is typically 2 ~ 4 working days. The lengthier the document the longer the lead time.

Question 2: Can I share the purchased PDF of GB/T 41641-2022_English with my colleagues?

Answer: Yes. The purchased PDF of GB/T 41641-2022_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.

Question 3: Does the price include tax/VAT?

Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countries

Question 4: Do you accept my currency other than USD?

Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay.