GB/T 40927-2021 PDF EnglishUS$185.00 · In stock · Download in 9 seconds
GB/T 40927-2021: Leather - Physical and mechanical tests - Determination of heat resistance of patent leather Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid
Similar standardsGB/T 40927-2021: Leather - Physical and mechanical tests - Determination of heat resistance of patent leather---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT40927-2021 NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 59.140.30 CCS Y 46 Leather - Physical and mechanical tests - Determination of heat resistance of patent leather (ISO 17232:2017, MOD) ISSUED ON: OCTOBER 11, 2021 IMPLEMENTED ON: MAY 01, 2022 Issued by: State Administration for Market Regulation; Standardization Administration of the People's Republic of China. Table of ContentsForeword ... 3 1 Scope ... 5 2 Normative references ... 5 3 Terms and definitions ... 5 4 Method A - Crack testing machine method ... 5 5 Method B - "Zwick" instrument method ... 8 Annex A (informative) Changes in the structure of this Standard compared to ISO 17232:2017 ... 12 Annex B (informative) Technical differences between this Standard and ISO 17232:2017 and their reasons ... 13 Leather - Physical and mechanical tests - Determination of heat resistance of patent leather1 ScopeThis Standard describes two test methods for determining the heat resistance of patent leather, respectively, the crack testing machine method (method A) and the "Zwick" instrument method (method B). This Standard is applicable to the determination of heat resistance of various types of patent leather. Other types of coated leather refer to it for the implementation.2 Normative referencesThe following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. GB/T 39364, Leather - Chemical, physical, mechanical and fastness tests - Sampling location (GB/T 39364-2020, ISO 2418:2017, MOD) QB/T 2707, Leather - Physical and mechanical tests - Sample preparation and conditioning (QB/T 2707-2018, ISO 2419:2012, MOD)3 Terms and definitionsThere are no terms and definitions that need to be defined in this document.4 Method A - Crack testing machine method4.1 Principle After the porous leather specimen is extended to a certain extent, heat the surface. Record the damage to the patent leather coating. 4.2 Instruments and equipment 4.2.1 The testing machine contains the following components: 4.3.3 Specimen perforation 4.3.3.1 Manual perforation Place the specimen patent leather surface up on the soft rubber pad (4.2.7). Use the needle (4.2.3) fixed on the bracket to perforate vertically within 1.0mm of the center of the specimen. Then drill 4 more holes at a distance of (5.0±0.5)mm from the first hole. Make it a simple cross with the first hole. Make sure that the needle penetrates the leather specimen to the soft rubber pad when perforating. 4.3.3.2 Machine perforation Fasten the needle (without threading) to the sewing machine. Move at normal speed to pierce the central area of the specimen. The perforation density is 6 needles/10mm. 4.3.4 Specimen adjustment Carry out according to the provisions of QB/T 2707. Test in the standard atmosphere used for conditioning. 4.4 Test steps 4.4.1 Adjust the testing machine so that the piston is at 0 scale or minimum top extension. 4.4.2 Fix the specimen on the testing machine with a fixture, so that the steel ball at the top of the piston acts on the meat surface of the specimen. 4.4.3 Start the testing machine. Make the steel ball at the top of the piston act on the specimen and extend it until the steel ball extension measuring device [4.2.1d)] shows (7.5 ± 0.05) mm. Inspect the specimen and record any damage to the specimen. 4.4.4 Place the sensor of the temperature measuring device (4.2.5) at (1.5±0.5) mm above the top extension of the specimen. Heat the specimen to (100±5)°C with a hot air blower (4.2.4) under standard test conditions. Maintain (180±5)s. Or use the hot air blower (4.2.4) to heat the specimen to (125±5)°C under extended test conditions. Maintain (300±5)s. Use the temperature measuring device to ensure that the above temperature is maintained for the specified time. If the temperature exceeds the allowable range, re-sample to test. 4.4.5 Maintain the top extension of the specimen. Recheck the specimen. Record any damage to the paint finish or grain of the specimen. 4.4.6 Repeat the operations in 4.4.1~4.4.5 for the remaining specimens. 4.5 Test report The test report shall contain the following: a) Reference to this Standard; b) The detailed information of the sample and the inconsistency with sampling in GB/T 39364; c) Any damage to the coating or grain of each specimen after jacking; d) Any damage to the coating or grain of each specimen after heating; e) Test temperature and time (such as 100°C/180s or 125°C/300s); f) Perforation method and conditions for specimen conditioning (standard atmosphere: 20°C/65%, 23°C/50% or 27°C/65%); g) Any deviation from the provisions of this method.5 Method B - "Zwick" instrument method5.1 Principle After the porous leather sample is stretched to a certain extent, heat the surface. Record the damage to the patent leather coating. 5.2 Instruments and equipment 5.2.1 Testing machine: Both ends of the specimen can be fixed on the fixture A and the horizontal fixture B respectively, so that it can be stretched in the D direction of the mandrel. The structural layout of the testing machine is shown in Figure 1, which mainly includes the following components: - Mandrel D: It consists of a horizontal semi-cylinder with a diameter of (15.0 ± 0.1) mm, a length of (25.5 ± 0.1) mm and a quarter sphere with a radius of (15.0 ± 0.1) mm. The lower end (fixed end) of fixture A is on the same level as the top line of mandrel D. Fixture B is located (11.0 ± 0.1) mm below the curved tip of the vertical mandrel. - Manual lever C: After connecting with fixture B, it can move up and down in quadrant E. The maximum distance the lever can move down is controlled by pins passing through the two holes at each end of the quadrant. It determines the maximum tensile strength of the specimen. There are pairs of holes in quadrant E. The pin can be inserted into any pair of holes to control the range of motion of the lever. The movement of the lever shall make the specimen linearly stretch by (21±1)%. Lock F enables Carry out according to the provisions of GB/T 39364. If it is not possible to take samples from standard parts (such as directly from shoes and clothing), samples shall be taken from any part of the available area. The specimen shall be representative and indicated in the test report. 5.3.2 Specimen preparation Use the die knife to cut 6 specimens from the surface of the patent leather. In which, the long sides of the 3 specimens are parallel to the direction of the ridge line. The long sides of the other 3 specimens are perpendicular to the direction of the ridge line. If there are more than 2 sheets in the same batch of leather that need to be tested, cut 1 specimen in each direction from each piece of leather to be tested. The total number of specimens in each direction is not less than 3. 5.3.3 Specimen perforation Run the sewing machine at normal speed with a fixed needle (without threading). Drill a row of holes in the middle of the specimen parallel to the long side. The pinhole density is 6 pins/10mm. 5.3.4 Specimen adjustment Carry out according to the provisions of QB/T 2707. The test need not be performed in standard atmosphere. 5.4 Test steps 5.4.1 Place the sensor of the temperature measuring device at (1.5±0.5)mm above the mandrel D. Use the hot air blower (5.2.4) to heat until the sensor displays (125±5)°C. Maintain (15±1)min. 5.4.2 Insert pins into a pair of holes in quadrant E that stretch the specimen by (21±1)%. 5.4.3 Raise the manual lever to the top of the quadrant and lock it. Insert the short-side patent leather surface of the specimen upwards into the center of the upper fixture (A). The specimen is laid flat around the mandrel. After tightening, fix the other end on the lower fixture (B). 5.4.4 Place the sensor of the temperature measuring device (1.5±0.5)mm above the specimen. Use the hot air blower to heat to (125±5)°C. Maintain (20±2)s. Pull down the manual lever substantially to make contact with the pin. Keep the specimen at (125±5)°C for (300±5)s. If the temperature is outside the above range, re-sample for testing. 5.4.5 Turn off the hot air blower. Raise the manual lever. Take out the specimen. ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 40927-2021 be delivered?Answer: The full copy PDF of English version of GB/T 40927-2021 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 40927-2021_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 40927-2021_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 40927-2021 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.How to buy and download a true PDF of English version of GB/T 40927-2021?A step-by-step guide to download PDF of GB/T 40927-2021_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 40927-2021". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
