GB/T 40404-2021 PDF EnglishUS$170.00 · In stock · Download in 9 seconds
GB/T 40404-2021: Slag material - Measurement of melting temperature - High temperature metallographic method Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid
Similar standardsGB/T 40404-2021: Slag material - Measurement of melting temperature - High temperature metallographic method---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT40404-2021 GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 77.040.99 CCS H 24 Slag material - Measurement of melting temperature -High temperature metallographic method ISSUED ON: AUGUST 20, 2021 IMPLEMENTED ON: MARCH 01, 2022 Issued by: State Administration for Market Regulation; Standardization Administration of the People's Republic of China. Table of ContentsForeword ... 3 1 Scope ... 4 2 Normative references ... 4 3 Terms and definitions ... 4 4 Method principle ... 4 5 Instruments and sample preparation equipment ... 5 6 Specimen preparation ... 6 7 Test steps ... 6 8 Test report ... 8 9 Test report ... 8 Bibliography ... 9 Slag material - Measurement of melting temperature -High temperature metallographic method1 ScopeThis document specifies the method principle, instrument and sample preparation equipment, specimen preparation, test steps and test report for the determination of melting temperature of slag materials. This document applies to the determination of smelting slag and continuous casting mold flux by high temperature metallographic method. This document can also be used for the determination of the melting temperature of ores with similar compositions as reference. This document does not apply to slag-type materials that react with platinum flakes.2 Normative referencesThe following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. YB/T 186, Method of the test for melting temperature of continuous casting mold powder3 Terms and definitionsFor the purposes of this document, the following terms and definitions apply. 3.1 melting temperature The temperature at which the slag specimen melts to form a circular arc and begins to flow uniformly outward. NOTE: The melting temperature of slag materials is mainly determined by the type and content of the composition.4 Method principleUse a high temperature microscope. Place the prepared cylindrical specimen on a 5.2.1 The crucible shall be an alumina crucible. Recommended crucible size: outer diameter is 9mm, inner diameter is 8mm, depth is 4mm, bottom thickness is 1mm. 5.2.2 Platinum gasket is used at the bottom of the crucible. The platinum gasket is 7mm in diameter and 0.05mm thick. 5.3 Forming mold The forming mold is made by stacking three stainless steel sheets of the same size with a thickness of 3mm. Fix with screws. The upper two pieces have more than 3 holes with a diameter of 3mm. The holes of which the diameter is 1.5mm, 2mm or other can also be used in special cases. When the specimen is pressed, a small die steel bar of the same diameter shall be used.6 Specimen preparation6.1 Sampling The sampling location shall be representative of the typical composition of the entire product. 6.2 Preprocessing For mold slag containing volatile matter or mold slag containing expanded graphite, it shall be pre-fired in a muffle furnace at 600℃ ~ 700℃ for at least 2h. 6.3 Sample preparation The specimen is pulverized into powder with a particle size of 0.074mm (200 mesh) or less. After mixing the powder and absolute ethanol in an agate mortar, take 5g~10g of the mixture in the molding die and compact it. Store in a desiccator. For individual samples that are difficult to compact, add a little dextrin. Use water to reconcile the specimen. 6.4 Specimen size and quantity Unless otherwise specified, the specimen is generally 3mm in diameter and 3mm in height. There are no less than 3 specimens in each group.7 Test steps7.1 Turn on the device. 7.2 Place the specimen upright on the platinum sheet in the crucible. Then place the crucible on the sample rod in the furnace. Cover the stove. ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 40404-2021 be delivered?Answer: The full copy PDF of English version of GB/T 40404-2021 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 40404-2021_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 40404-2021_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 40404-2021 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.How to buy and download a true PDF of English version of GB/T 40404-2021?A step-by-step guide to download PDF of GB/T 40404-2021_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 40404-2021". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
