GB/T 40401-2021 English PDFUS$264.00 · In stock
Delivery: <= 3 days. True-PDF full-copy in English will be manually translated and delivered via email. GB/T 40401-2021: Determination of density by volumetric displacement - Skeleton density by gas pycnometry Status: Valid
Basic dataStandard ID: GB/T 40401-2021 (GB/T40401-2021)Description (Translated English): Determination of density by volumetric displacement - Skeleton density by gas pycnometry Sector / Industry: National Standard (Recommended) Classification of Chinese Standard: A28 Word Count Estimation: 14,183 Issuing agency(ies): State Administration for Market Regulation, China National Standardization Administration GB/T 40401-2021: Determination of density by volumetric displacement - Skeleton density by gas pycnometry---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order. Determination of density by volumetric displacement - Skeleton density by gas pycnometry ICS 19.120 CCSA28 National Standards of People's Republic of China Skeleton density measurement gas volume displacement method (ISO 12154.2014, IDT) Released on 2021-08-20 2022-03-01 implementation State Administration of Market Supervision and Administration Issued by the National Standardization Management Committee Table of contentsForeword Ⅰ Introduction Ⅱ 1 Scope 1 2 Normative references 1 3 Terms and definitions 1 4 Symbol 2 5 Measuring principle 2 6 Measuring instruments and measuring procedures 3 7 Test report 6 Appendix A (Informative) Interference 8 Reference 10ForewordThis document is in accordance with the provisions of GB/T 1.1-2020 "Guidelines for Standardization Work Part 1.Structure and Drafting Rules of Standardization Documents" Drafting. The translation method used in this document is equivalent to the ISO 12154.2014 "Skeleton Density Measurement Gas Volume Replacement Method". The Chinese documents that have consistent correspondence with the normatively cited international documents in this document are as follows. ---GB/T 19587-2017 Gas adsorption BET method to determine the specific surface area of solid materials (ISO 9277.2010, IDT); ---GB/T 21650.3-2011 Determination of pore size distribution and porosity of solid materials by mercury intrusion method and gas adsorption method Part 3.Gas Analysis of micropores by volume adsorption method (ISO 15901-3.2007, IDT). This document was proposed and managed by the National Technical Committee on Particle Characterization and Sorting and Screen Standardization (SAC/TC168). Drafting organizations of this document. Shanghai Institute of Metrology and Testing Technology, China Academy of Metrology, Shenzhen Guoji Instrument Co., Ltd., Beishi German Instrument Technology (Beijing) Co., Ltd., LinkTech (Beijing) Instrument Technology Co., Ltd., Anton Paar (Shanghai) Trading Co., Ltd., Zhongjisheng Productivity Promotion Center. The main drafters of this document. Wu Limin, Chen Ying, Wang Hai, Zhou Ying, Liu Jianfeng, Yang Zhenghong, Hou Changge, Zhou Yan, Wang Meiling, Zhu Ping.IntroductionThe true density of a solid material is defined as the ratio of the mass to the volume occupied by the mass. Therefore, when calculating the true density, the particle The corresponding volume occupied by pores or inter-particle voids and inter-particle gaps (such as granular or highly dispersed samples). If the material has no pores, as long as the test liquid does not react with the material, it can be measured by measuring the volume of the solid discharged from the liquid. Get the true density. The accuracy of this method depends on the accuracy of the liquid volume measurement. However, usually the test liquid will not penetrate completely easily Enter the pores, cracks, and fissures of the material. In these cases, if the material does not contain closed pores that cannot be penetrated by the analysis gas, gas can be used instead of liquid. The volume measures the true density of the material. Therefore, the density measured by the gas densitometer method is usually called the material skeleton density, which is equivalent to the solid without closed cells. The true density of the state material. The device used to measure the volume of solids is usually called a gas density meter, derived from the Greek "pyknos", which means thick or dense, gas density The meter can also analyze materials with irregular shapes. After determining the volume and mass of the solid framework of the sample, the framework density can be easily calculated. Skeleton density measurement gas volume displacement method1 ScopeThis document specifies a method to quickly and effectively determine the skeleton density of solid material samples with regular or irregular shapes by the gas densitometer method. Degree methods include powder or whole single-piece samples.2 Normative referencesThe contents of the following documents constitute the indispensable clauses of this document through normative references in the text. Among them, dated quotations Only the version corresponding to that date is applicable to this document; for undated reference documents, the latest version (including all amendments) is applicable to This document. ISO 9277 Gas adsorption BET method to determine the specific surface area of solid matter (Determination of the specific surface area of solidsbygasadsorption-BETmethod) ISO 14488 Particle Sampling and Sample Separation Method for Determination of Particle Characteristics (Particulatematerials-Sampling andsamplesplittingforthedeterminationofparticulateproperties) ISO 15901-3 Determination of pore size distribution and porosity of solid materials by mercury intrusion method and gas adsorption method Part 3.Analysis by gas adsorption method Microporous (Poresizedistributionandporosityofsolidmaterialsbymercuryporosimetryandgasadsorp- tion-Part 3.Analysisofmicroporesbygasadsorption)3 Terms and definitionsThe following terms and definitions apply to this document. 3.1 Density The ratio of the mass of the sample to the volume occupied by the mass. 3.2 Truesolidstatedensity The ratio of the mass of the sample to the volume of the dense solid framework of the sample, excluding open and closed pores, internal voids of particles, and coarse particles or height The volume of the gap between the dispersed particles. 3.3 Skeleton density The ratio of sample mass to sample volume, where the volume includes the volume of closed pores that may exist, but does not include the volume of open pores and bulk samples The volume of the inter-particle gap. 3.4 Closedpore A hole that is completely closed by the hole wall, does not communicate with other pores, and cannot enter any fluid. ......Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of GB/T 40401-2021_English be delivered?Answer: Upon your order, we will start to translate GB/T 40401-2021_English as soon as possible, and keep you informed of the progress. The lead time is typically 1 ~ 3 working days. The lengthier the document the longer the lead time.Question 2: Can I share the purchased PDF of GB/T 40401-2021_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 40401-2021_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay. |
