GB/T 39935-2021 English PDFUS$184.00 · In stock
Delivery: <= 3 days. True-PDF full-copy in English will be manually translated and delivered via email. GB/T 39935-2021: Plastics - Film and sheeting - Determination of blocking resistance Status: Valid
Basic dataStandard ID: GB/T 39935-2021 (GB/T39935-2021)Description (Translated English): Plastics - Film and sheeting - Determination of blocking resistance Sector / Industry: National Standard (Recommended) Classification of Chinese Standard: G33 Word Count Estimation: 10,188 Issuing agency(ies): State Administration for Market Regulation, China National Standardization Administration GB/T 39935-2021: Plastics - Film and sheeting - Determination of blocking resistance---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order.Plastics - Film and sheeting - Determination of blocking resistance ICS 83.140.10 G33 National Standards of People's Republic of China Plastic products film and sheet Determination of blocking resistance (ISO 11502.2018, IDT) Released on 2021-03-09 2021-10-01 implementation State Administration of Market Supervision and Administration Issued by the National Standardization Management Committee ForewordThis standard was drafted in accordance with the rules given in GB/T 1.1-2009. The translation method used in this standard is equivalent to ISO 11502.2018 "Determination of Anti-blocking Properties of Plastic Films and Sheets". The Chinese documents that have a consistent correspondence relationship with the normatively cited international documents in this standard are as follows. ---GB/T 2918-2018 Standard environment for condition adjustment and testing of plastic specimens (ISO 291.2008, MOD). Please note that some of the contents of this document may involve patents. The issuing agency of this document is not responsible for identifying these patents. This standard was proposed by the China National Light Industry Council. This standard is under the jurisdiction of the National Standardization Technical Committee for Plastic Products (SAC/TC48). This standard was drafted by. Kunshan Achilles New Material Technology Co., Ltd., Kunshan Achilles Testing Technology Service Co., Ltd., Suzhou Ai Chibot Testing Technology Co., Ltd., Beijing Technology and Business University, Shanghai Ruowei New Material Technology Co., Ltd., Kunshan Xiefu New Material Co., Ltd. Company, GAC Passenger Vehicle Co., Ltd., Chongqing Changan Automobile Co., Ltd., BYD Automobile Industry Co., Ltd., Nanjing University of Science and Technology, Sichuan University, Geely Automobile Research Institute (Ningbo) Co., Ltd., Dongguan Longde Shoe Material Co., Ltd., Guanbiao (Shanghai) Testing Technology Co., Ltd. The main drafters of this standard. Zhao Jianming, Chen Qing, Ding Runkang, Xu Bo, Wei Liming, Mu Guobao, Ding Jufang, Zou Jianfeng, Zhang Feng, Mao Hu, Zhang Xiaoxiao, Jia Hongbing, Fan Haojun, Gao Chaoqian, Zhu Wencheng, Wang Weixin. Plastic products film and sheet Determination of blocking resistance1 ScopeThis standard specifies the use of qualitative analysis and quantitative analysis to evaluate the interaction of soft plastic films and sheets at specified temperatures and pressures. A method of measuring adhesion after a period of time.2 Normative referencesThe following documents are indispensable for the application of this document. For dated reference documents, only the dated version applies to this article Pieces. For undated reference documents, the latest version (including all amendments) is applicable to this document. ISO 291 Standard environment for condition adjustment and testing of plastic specimens (Plastics-Standardatmospheresfor conditioningandtesting)3 Terms and definitionsThe following terms and definitions apply to this document. The International Organization for Standardization and the International Electrotechnical Commission maintain a database of terminology for standardization. The website is as follows. 3.1 Blocking Non-artificial bonding between materials. 4 Method A--- Qualitative Analysis Method 4.1 Principle Under the condition of 7kPa pressure and constant temperature of 50℃, the plastic film or sheet should be closely attached and kept for at least 24h. If the bonding material is in the distribution During the separation process, it is damaged or the adhesion force between the surfaces is greater than a specified load, which indicates that the material is adhesion. The test time, temperature and pressure can be selected according to the characteristics of the test film or sheet and the actual use conditions of the material. 4.2 Test equipment 4.2.1 Glass sheet 100mm×76mm, thickness is about 2mm. 4.2.2 Filter paper strips 150mm×76mm. 4.2.3 Oven The control temperature is (50±2)℃. At the same time, ensure that after multiple samples are put in, there is at least a 50mm interval between each other, and the side wall of the oven Above 50mm. 4.2.4 Load The mass is 5.4kg. 4.2.5 Metal bars The cross section is rectangular, the length×width is 76mm×15mm, and the weight is 50g and 100g each. 4.2.6 Metal clip The length of the arm is about 100mm. 4.2.7 Double-sided tape The width is about 12.5mm. 4.3 Test sample 4.3.1 Sampling size The sample size is 150mm×76mm. The surface of the material with printed or decorative patterns is the test surface, and the reverse is the back. Wakasai The material has no printing or decorative patterns, and either side is the test surface and is marked during the test. 4.3.2 Sample preparation Take six samples. If the sample contains a variety of printed patterns and patterns, the sample is cut to include all the features of the pattern and pattern. Coil samples The sample is cut more than 100mm from the edge, and more than 1m from the start and end. Test at least 16h after sample production. 4.4 Test procedure 4.4.1 The samples, glass slides and filter paper strips shall be adjusted for 24 hours in accordance with ISO 291. 4.4.2 Place the sample, filter paper and glass slide in the following order. glass slide/filter paper/sample with test side up/sample with test side down/ Filter paper/glass slide. Align the above-mentioned sample combination all along its 76mm edge (see Figure 1). A total of three sets of samples are prepared, excluding the case where the back side and the front and back of the two samples are bonded. 4.4.3 Put the sample combination into the oven and load a load of 5.4kg to ensure that the sample is subjected to a uniform pressure of 7kPa. At (50±2)℃ Keep it for 24h. After the end, unload the load, take the sample combination out of the oven and place it in a standard atmospheric environment for more than 2h, but not exceeding After 24h. 4.4.4 Take out each pair of samples from the sample combination and place them flat on a horizontal table. Use double-sided tape to glue a 50g or 100g metal strip to the free end of the lower sample (see Figure 2). And use double-sided on the other end of the lower sample Glue on the horizontal surface. Without printing surface, use 50g metal strip. It has a printing surface and uses 100g metal strips. There is a printed sheet in the depression or interlayer, which is treated the same as a non-printed surface. Clamp the free end of the specimen with a metal clamp, and ensure that it clamps the entire width of the specimen. Lift by hand at a uniform speed of (25±2.5) mm/s Lift the metal clip until the sample is completely separated. Record whether the metal strip is lifted from the horizontal surface. Observe whether there are obvious visible cracks on the surface of the sample. 4.4.5 If the metal strip is lifted from the horizontal surface or the surface of the sample is damaged during the separation of the sample, it means that the material is stuck. 4.5 Test report The test report includes. a) This standard number and method A; b) Complete and necessary valid information to identify the sample material; c) Information on the metal strip material used; d) Whether there is adhesion and damage, record it; e) Test date. 5 Method B---Quantitative Analysis Method 5.1 Principle After the sample combination is kept at a certain temperature and pressure for a certain period of time, the sample is fixed between the two clamps of the tensile testing machine to determine And record the load required to separate it. 5.2 Test equipment 5.2.1 Constant speed tensile testing machine The upper and lower aluminum fixture specifications are 100mm×100mm. 5.2.2 Glass sheet 100mm×76mm, thickness is about 2mm. 5.2.3 Filter paper strips 100mm×76mm. 5.2.4 Load The mass is 2.3kg. 5.2.5 Oven The temperature can be maintained at (50±2)℃. 5.2.6 Double-sided tape 5.3 Test sample 5.3.1 Sampling size The sample size is 150mm×76mm. The long side of the sample is parallel to the side of the tester fixture. 5.3.2 Sample preparation Cut ten samples at different positions in the width direction of the sample. The coil sample is cut more than 100mm from the edge, and the distance between the starting end and the 1m above the end. Test at least 16h after sample production. 5.4 Test procedure 5.4.1 The samples, glass slides and filter paper strips shall be adjusted for 24 hours in accordance with ISO 291. 5.4.2 Prepare 5 groups of test combinations, each group contains the same two samples as described in Method A, two filter paper strips and two glass slides. but The edges of each layer are placed as shown in Figure 3.The orientation of the sample surface can be determined by the user (for example, judged by the test results of Method A). But should Ensure that the directions of the five sets of samples are consistent. Combine the sample in a (50±2)℃ oven and load 2.3kg (equivalent to 3kPa) and keep it for 3h. After the end, unload the load and take out the sample assembly. Take out each pair of samples from the sample combination and place them in a standard atmospheric environment for more than 2 hours, but not More than 24h. 5.4.3 Use a blade or spatula to place a pair of specimens on the lower clamp of the tensile testing machine, keeping the specimen in the center of the clamp (see Figure 4). 5.4.4 Raise the lower clamp until the upper clamp is close to directly above the specimen and the lower clamp. 5.4.5 Separate the edges of the specimen with a knife edge and fold them in the direction of the nearest fixture. 5.4.6 Use double-sided tape to fix the upper sample on the upper fixture, and the lower sample on the lower fixture (see Figure 5). 5.4.7 Adjust the paper speed of the tensile tester's recorder to 50mm/min, and the beam speed to 5mm/min. 5.4.8 Turn on the tensile testing machine and record the separation load during the whole process. 5.4.9 Repeat the above operation for the remaining 4 sets of sample combinations. 5.4.10 Record the maximum value of each group of sample combinations and calculate the average of the five groups. Note. This method can be used to measure the force required to separate the adhered sample. However, the conditions under which adhesion occurs are unknown and may be different from those specified in this method. Conditions, it is unreasonable to directly compare the results obtained with the above methods. ......Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of GB/T 39935-2021_English be delivered?Answer: Upon your order, we will start to translate GB/T 39935-2021_English as soon as possible, and keep you informed of the progress. The lead time is typically 1 ~ 3 working days. The lengthier the document the longer the lead time.Question 2: Can I share the purchased PDF of GB/T 39935-2021_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 39935-2021_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay. |
