GB/T 3903.4-2017 PDF EnglishUS$80.00 · In stock · Download in 9 seconds
GB/T 3903.4-2017: Footwear -- Test methods for whole shoe -- Hardness Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid GB/T 3903.4: Historical versions
Similar standardsGB/T 3903.4-2017: Footwear -- Test methods for whole shoe -- Hardness---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT3903.4-2017GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 61.060 Y 78 Replacing GB/T 3903.4-2008 Footwear -- Test methods for whole shoe -- Hardness Issued on: DECEMBER 29, 2017 Implemented on: JULY 1, 2018 Issued by. General Administration of Quality Supervision, Inspection and Quarantine of the People’s Republic of China; Standardization Administration of the People’s Republic of China. Table of ContentsForeword . 3 1 Scope .. 4 2 Normative references . 4 3 Principle.. 4 4 Apparatus . 4 5 Test piece . 5 6 Test conditions . 5 7 Test procedures . 6 8 Test results .. 6 9 Test report . 7 Footwear -- Test methods for whole shoe -- Hardness1 ScopeThis Standard specifies the test methods for hardness of footwear outsoles and heels. This Standard is applicable to the determination of the hardness of whole shoe outsoles and heels. NOTE. The sole materials (sheets) can be determined with reference to this Standard.2 Normative referencesThe following documents are essential to the application of this document. For dated references, only the editions with the dates indicated are applicable to this document. For undated references, only the latest editions (including all the amendments) are applicable to this document. GB/T 531.1-2008 Rubber vulcanized or thermoplastic -- Determination of indentation hardness -- Part 1. Durometer method (Shore hardness) GB/T 22049 Footwear -- Standard atmospheres for conditioning and testing of footwear and components for footwear HG/T 2489-2007 Cellular for shoes -- Determination of hardness 3 Principle USE a Shore durometer. PRESS the indenter of the prescribed shape into the test piece under certain conditions. MEASURE the depth of vertical indentation. CONVERT it to a hardness value. The test results are influenced by the shape of the indenter and the applied pressure. Therefore, there is no simple correspondence between the results of tests using different types of durometers.4 Apparatus4.1 Durometer7 Test procedures7.1 CHECK the test pieces. If there are any impurities on the surface, USE gauze moistened with alcohol to wipe them clean. 7.2 SELECT the flat surface of the sole or the main material of the heel as the test site (if the product standard stipulates the test site, SELECT the flat part at the specified test site). If there is no flat part, it shall be grinded. The grinding depth shall be based on the exact removal of patterns, so that the surface of the test piece is flat. When testing the cellular materials, the compact layer on the surface shall be grinded to ensure that the surface of the test piece is flat, without any mechanical damages and impurities. If the whole shoe or outsole is equipped with the shank, the shank shall be avoided. 7.3 According to the provisions of GB/T 22049, the test piece shall be placed at a temperature of (23 ± 2) °C in the standard environment for at least 4h. 7.4 Where necessary, the durometer can be mounted on the bracket. 7.5 PLACE the test piece on a hard surface, with the test site facing upwards. KEEP the surface level. PRESS the indenter foot onto the test piece at a uniform speed with no vibration as far as possible. KEEP the indenter foot parallel to the surface of the test piece. The indenter is perpendicular to the surface of the test piece and is not less than 12mm from the edge of the test specimen. APPLY enough pressure. After the indenter foot is in complete contact with the test specimen for 3s, READ the value. 7.6 For each test piece, measurements shall be taken at 3 or more points. Hardness can only be measured once at each measuring point. The distance between the points is not less than 6mm.8 Test results8.1 RECORD the types of the durometers in use. The value indicated by the durometer pointer is the measured value. The unit is expressed in degrees. 8.2 TEST the two shoes (soles) in each set of test pieces, respectively. MEASURE each shoe (sole) at 3 points. At the time of an arbitration test, MEASURE at 5 points. TAKE the arithmetic mean as the test result of the shoe (sole). The absolute value of the relative deviation between each measured value and the mean value shall not exceed 5%. If exceeding the deviation, the values exceeding the deviation shall be discarded, and additional measurements shall be made. The test results shall be rounded. At the time of a dispute or an arbitration test, the results measured using the bracket shall prevail. ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 3903.4-2017 be delivered?Answer: The full copy PDF of English version of GB/T 3903.4-2017 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 3903.4-2017_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 3903.4-2017_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 3903.4-2017 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.Question 5: Should I purchase the latest version GB/T 3903.4-2017?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 3903.4-2017 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically.How to buy and download a true PDF of English version of GB/T 3903.4-2017?A step-by-step guide to download PDF of GB/T 3903.4-2017_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 3903.4-2017". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
