GB/T 3903.3-2011 PDF EnglishUS$170.00 · In stock · Download in 9 seconds
GB/T 3903.3-2011: Footwear -- General test methods -- Peeling strength Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid GB/T 3903.3: Historical versions
Similar standardsGB/T 3903.3-2011: Footwear -- General test methods -- Peeling strength---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT3903.3-2011GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 61.060 Y 78 Replacing GB/T 3903.3-1994 Footwear - General test methods - Peeling strength Issued on: DECEMBER 31, 2011 Implemented on: FEBRUARY 01, 2012 Issued by. General Administration of Quality Supervision, Inspection and Quarantine; Standardization Administration of the People’s Republic of China. Table of ContentsForeword... 3 1 Scope... 4 2 Terms and definitions... 4 3 Test sample and conditioning... 4 4 Test instrument... 5 5 Test methods... 6 6 Result calculation and expression... 7 7 Test report... 8 Appendix A (Normative) Dynamometer test method... 9 Footwear - General test methods - Peeling strength1 ScopeThis Part of GB/T 3903 specifies the test method for the peeling strength between the sole and the upper of a whole shoe or between the outsole and the outer midsole. This Part applies to footwear made by molding, vulcanization, injection molding, perfusion, gluing and other processes. This Part does not apply to sewn footwear.2 Terms and definitionsFor the purposes of this document, the following terms and definitions apply. 2.1 peeling strength of whole shoes The force per unit width when the peel tester peels the sole and the upper or the outsole and the outer midsole apart to a specified width. 2.2 off-bonding A phenomenon of just-off-bonding along the cutting edge between the objects being tested.3 Test sample and conditioning3.1 The test sample shall be finished shoes made 48 hours after manufacture. There shall be no obvious defects on the test parts. The test samples shall be left for at least 4 hours before testing. 3.2 Each set of test samples from the same batch of products shall generally contain no less than one pair of shoes. 3.3 The test environment must be laboratory room temperature.4 Test instrument4.1 Peel tester, maximum load not less than 392 N. 4.1.1 Dynamometer 4.1.1.1 For elastic body, the linear deviation, indication deviation and indication variation shall not exceed 3%. 4.1.1.2 When using a force table, do not consider linear deviation. 4.1.1.3 The dynamometer shall be inspected at least once a year and shall be re- inspected after replacing, disassembling or moving the dynamometer parts. 4.1.1.4 The dynamometer shall be tested in accordance with Appendix A. 4.1.2 Peeling knife 4.1.2.1 The blade is located on the center line (neutral layer) of the dynamometer, and the curvature of the blade shall be basically consistent with the curvature of the measured part. The specifications and dimensions of the peeling knife are shown in Figure 1. 4.1.2.2 The blade width is available in two specifications. (20 ± 0.2) mm and (10 ± 0.2) mm, which may be selected according to the relevant product standards during testing. The downward speed of the peeling blade is (20±2) mm/min. 4.1.3 The distance between the positioning rod and the pull rod shall not be less than 50 mm. 4.1.4 The graduation value of the force gauge is 1 N, and the graduation value of the micrometer is 1 μm. 4.2 Steel ruler, graduation 1 mm.5 Test methods5.1 Adjust the force gauge or micrometer to zero. 5.2 Adjust the force gauge to an upward tilt of 5°~10° with respect to the horizontal plane. 5.3 Adjust the downward speed of the peeling blade (i.e., the downward speed of the blade) to (20±2) mm/min. 5.4 Placement of test samples 5.4.1 Install the shoe on a matching shoe last, ensuring that the shoe fits the last at the stripping position; place the shoe naturally and flatly on the horizontal plate of the tester's clamp; then clamp the shoe; adjust the height and front-to-back position of the clamp so that the stripping blade is aligned with the test area. The length of the test part extending from the test bench is 20 mm ~ 40 mm. 5.4.2 For outsoles with protruding edges, the blade should rest on the edge of the outsole. Without causing the blade to slip, the blade shall be as close to the joint seam of the test part as possible. For outsoles without protruding edges or outsole and midsole, the blade shall rest on the outsole below the joint seam of the test part. Under no circumstances shall the blade cut the joint seam between the upper and the sole. 5.4.3 If the shoe is tilted left or right and cannot be aligned with the blade, it is permitted to place a washer under the sole to straighten the shoe. 5.4.4 After the bottom of shoe or bottom wall is cut, the force gauge or micrometer may deviate from the zero position. This is normal. However, the deflection of the dial indicator must not exceed 10 μm, and the force gauge must not exceed 5 N. Do not adjust the dial indicator or force gauge at this time. 5.5 After starting the machine and running the peeling blade downward, attention shall be paid constantly to the changes in the joint conditions of the test area. If off-bonding is found, stop the machine immediately and read the meter value. 5.6 If any of the following conditions occurs, stop the test and record the maximum value. a) The upper and sole cannot be peeled off after three tests due to special reasons such as the sole being too soft or too thin; b) The upper or the outsole or midsole of the shoe is torn; ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 3903.3-2011 be delivered?Answer: The full copy PDF of English version of GB/T 3903.3-2011 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 3903.3-2011_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 3903.3-2011_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 3903.3-2011 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.Question 5: Should I purchase the latest version GB/T 3903.3-2011?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 3903.3-2011 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically.How to buy and download a true PDF of English version of GB/T 3903.3-2011?A step-by-step guide to download PDF of GB/T 3903.3-2011_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 3903.3-2011". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
