GB/T 38446-2020 English PDFUS$259.00 ยท In stock
Delivery: <= 3 days. True-PDF full-copy in English will be manually translated and delivered via email. GB/T 38446-2020: Micro-electromechanical system technology - Test methods for tensile property measurement of strip thin films Status: Valid
Basic dataStandard ID: GB/T 38446-2020 (GB/T38446-2020)Description (Translated English): Micro-electromechanical system technology - Test methods for tensile property measurement of strip thin films Sector / Industry: National Standard (Recommended) Classification of Chinese Standard: L55 Classification of International Standard: 31.200 Word Count Estimation: 14,146 Date of Issue: 2020-03-06 Date of Implementation: 2020-10-01 Issuing agency(ies): State Administration for Market Regulation, China National Standardization Administration GB/T 38446-2020: Micro-electromechanical system technology - Test methods for tensile property measurement of strip thin films---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order. Micro-electromechanical system technology--Test methods for tensile property measurement of strip thin films ICS 31.200 L55 National Standards of People's Republic of China Microelectromechanical system (MEMS) technology Test method for tensile properties of ribbon film Released on 2020-03-06 2020-10-01 implementation State Administration of Market Supervision and Administration Issued by the National Standardization Management Committee ContentsForeword I 1 Scope 1 2 Normative references 1 3 Terms and definitions 1 4 Test method 2 5 Data processing 4 Appendix A (informative appendix) Sample preparation using MEMS process 5 Appendix B (informative appendix) The effect of alignment deviation and geometry on performance testing 7 Appendix C (informative appendix) Test result error and compensation of the nano-indenter 9 Reference 10ForewordThis standard was drafted in accordance with the rules given in GB/T 1.1-2009. This standard was proposed and managed by the National Micro-Electromechanical Technology Standardization Technical Committee (SAC/TC336). This standard was drafted by. Peking University, China Machine Productivity Promotion Center, Beijing Zhixin Sensor Technology Co., Ltd., Wuxi China Resources Shanghua Technology Co., Ltd., North University of China, Beijing Bichuang Technology Co., Ltd. The main drafters of this standard. Zhang Wei, Li Haibin, Zhang Yating, Zhu Yue, Xia Changfeng, Shi Yunbo, Chen Demin, Ma Shucong, Cheng Hongbing, Zhou Haonan. Microelectromechanical system (MEMS) technology Test method for tensile properties of ribbon film1 ScopeThis standard specifies the test method and data processing of the tensile properties of the ribbon film. This standard applies to samples with a thickness between 50nm and a few microns and a ratio of length to thickness greater than 300. It can also be used for MEMS Quality control of the product film structure.2 Normative referencesThe following documents are essential for the application of this document. For dated references, only the dated version applies to this article Pieces. For the cited documents without date, the latest version (including all amendments) applies to this document. GB/T 26111 Technical terms for microelectromechanical system (MEMS)3 Terms and definitionsThe terms and definitions defined in GB/T 26111 and the following apply to this document. 3.1 Modulus of elasticity When the material is in the stage of elastic deformation, the ratio of stress to strain. Note. Rewrite GB/T 3102.3-1993, definition 3.18.1. 3.2 Yield strength yieldstrength Re When the material exhibits a yielding phenomenon, the stress point at which plastic deformation occurs and the force does not increase during the test is reached. Note 1. Rewrite GB/T 228.1-2010, definition 3.10.2. Note 2. For materials with obvious yield phenomena, the yield strength is the stress at the yield limit of the material when the yield phenomenon occurs; for materials where the yield phenomenon is not obvious, The yield strength is the stress when the strain reaches 0.2% of the residual strain. 3.3 Tensile strength Rm The corresponding maximum stress during the material breaking process. Note. Rewrite GB/T 228.1-2010, definition 3.10.1. 3.4 Deflection The linear displacement of the sample structure axis in the direction perpendicular to the axis or the linear displacement of the midplane in the direction perpendicular to the midplane. ......Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of GB/T 38446-2020_English be delivered?Answer: Upon your order, we will start to translate GB/T 38446-2020_English as soon as possible, and keep you informed of the progress. The lead time is typically 1 ~ 3 working days. The lengthier the document the longer the lead time.Question 2: Can I share the purchased PDF of GB/T 38446-2020_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 38446-2020_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay. |
